Troy-Biltメーカー466の使用説明書/サービス説明書
ページ先へ移動 of 20
21” Self Pr opelled Mulching Mo wer Model 466 PRINTED IN U .S .A. Oper ator’ s Man ual FORM NO . 769-00955.f m (10/2003) IMPORT ANT : Read saf ety rules and instructions ca refully before oper ating equipment.
2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Manual is an import ant part of your new lawn mower. It will help you asse mble, prepare and maintain the unit fo r best performance.
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES General Oper ation 1. Read this operator’s man ual carefully in its entirety before atte mpting to assemble this machine. Read, understand, and follow all instructions on the machine and in the manua l(s) before operation.
4 your footing, release the blade con trol handle immediately and th e blade will stop rotating within three seconds. 9. Mow in daylight or good artificial ligh t; walk, not run. 10. Stop th e blade when cr ossing gravel drives, walkways or roads. 11.
5 9. Never remove gas cap or add fu el while the engine is hot or running. Allow engine to co ol at least two minutes befo re refueling. 10. Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of filler nec k to provide space for fuel expansion.
6 SECTION 2: SLOPE GAUGE Use this page as a guide to determine slopes where y ou may not operate safely. 15 o SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE A CORNER OF A BUILDING OR A FE.
7 SECTION 3: ASSEMBLING YOUR LAWN MOWER Removing Unit From Carton • Remove staple s, break glue on top flap s, or cut tape at carton end an d peel along top flap to open. • Remove loose parts included with unit (i. e., operator’s manu al, oil, etc.
8 Attaching Starter Rope The rope guide is already at tached to the right side of the lower handle of your mowe r. See Figure 4 . • With spark p lug wire disconnect ed and grounded, hold the blade control hand le against the upper handle, and pu ll the starter rope ou t of the engine.
9 SECTION 4: KNOW YOUR LAWN MOWER Read this ow ner’s manual and safety rule s before operating your lawn mower. Compar e the illustrations in Figure 8 with your lawn mower to familiarize yourself with the location of various contro ls and adjustments.
10 SECTION 5: OPERATING YOUR LAWN MOWER Gas & Oil Fill-Up • Check oil level and add oil if necessary. Follow relevant instr uctions in the engine manual for this. • Service the engine with gasoline as instr ucted in the engine ma nual. Before Starting Mow er • Attach spark plu g wire to spark plug.
11 SECTION 6: MAINTAINING YOUR LAWN MOWER Cleaning Mower The underside of the mowe r deck should be cleaned after each use to preven t any build-up of grass clippings, leaves, dirt , or other debris. If this de bris is allowed to accumu late, it will result in rust and corrosion.
12 Engine • Follow the engine manu al instructions and recommended schedule for lubricating engine components. Blade Care • Periodically inspect the blade adapter and pulley for cracks, especially if yo u strike a fore ign object. Replace when necessary.
13 SECTION 7: SERVICE & ADJUSTMENTS Replacing Drive Belt • Remove two shoulder screws securing th e front drive cover to the mower de ck. See Figure 11. Figure 11 • Press inward o n the sides of t he front drive cover and releas e the tabs that secure t he front drive cover to the height adjuster bracket s.
14 Figure 14 • Reassemble t he upper handle to the lower hand le. • Place the hairpin clips in the inner holes of the we ld pins and replace th e carriage bolts and wing nuts on the handle bra ckets. Attach the star ter rope as instructed in the Assembly section.
15 SECTION 9: TROUBLE-SHOOTING NOTE: For repairs beyond t he minor adjust ments listed ab ov e, contact your local authorize d service dealer. Pr ob lem P ossible Cause Corrective Ac tion Engine fails to start 1. Blade control handle disenga ged 2. Spark plug wire disconnected 3.
16 SECTION 10: PARTS LIST FOR MODEL 466 IMPORTANT: For a proper working machine, use Factory Approved Parts. V-BELTS are specially designed to en gage and disengag e safely. A substitute (non OEM) V-Belt can be dangerous by not disengaging co mpletely.
17 Model 466 Ref. No P art N o. Description 1. 747-1214 Lower Bail Handle 2. 710-0599 TT Screw 1/4-20 x 0.5 3. 736-0270 Bell Washer.265 x 0.75 4. 17032A Deflector Chute Adapter 5. 732-1014 Torsion Spring 6. 731-04204 Deluxe Bail Cover 7. 747-1161A Blade Control Ha ndle 8.
18 NOTES.
19 NOTES.
MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth be low is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States, its possessions an d territories.
デバイスTroy-Bilt 466の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Troy-Bilt 466をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTroy-Bilt 466の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Troy-Bilt 466の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Troy-Bilt 466で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Troy-Bilt 466を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTroy-Bilt 466の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Troy-Bilt 466に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTroy-Bilt 466デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
