Troy-Biltメーカー469の使用説明書/サービス説明書
ページ先へ移動 of 20
21” Self Pr opelled Mulching Mo wer Models 466 & 469 PRINTED IN U .S .A. Oper ator’ s Man ual FORM NO . 769-00955A.f m (10/2004) IMPORT ANT : Read saf ety rules and instructions ca refully before oper ating equipment.
2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Manual is an important part of your new lawn mower. It will help y ou assemble, prepare and maintain the unit fo r best perform ance.
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES General Oper ation 1. Read this operator’s man ual carefully in its entirety before atte mpting to assemble t his machine. Read, understand, and follow all instructions on the machine and in the manual (s) before operatio n.
4 your footing, release the blade control ha ndle immediately and th e blade will stop rotating within three seconds. 9. Mow in daylight or good artificial ligh t; walk, not run. 10. Stop th e blade when cr ossing gravel drives, walkways or roads. 11.
5 9. Never remove ga s cap or a dd fuel wh ile the eng ine is hot or running. Allow engine to co ol at least two minutes befo re refueling. 10. Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of filler neck to provide space for fuel expansion.
6 SECTION 2: SLOPE GAUGE Use this page as a guide to determine slopes where y ou may not operate safely. 15 o SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE A CORNER OF A BUILDING OR A FE.
7 SECTION 3: ASSEMBLING YOUR LAWN MOWER Removing Unit From Cart on • Remove stap les, break glue on top flaps, or cut tape at carton en d and peel along top fla p to open. • Remove loose parts included with unit (i. e., operator’s manu al, oil, etc.
8 Attaching Starter Rope The rope guide is already at tached to the right side of the lower handle of you r mower. See Figure 4 . • With spark p lug wire discon nected and g rounded, hold the blade control hand le against the upper handle, and pu ll the starter rope out of the engine .
9 SECTION 4: KNOW YOUR LAWN MOWER Read this owner’s manua l and safety rules befo re operating your lawn mower. Com pare the illust rations in Figure 8 with your lawn mower to familiarize yourself with the location of various cont rols and adjustments.
10 SECTION 5: OPERATING YOUR LAWN MOWER Gas & Oil Fill-Up • Check oil level and add oil if necessary. Follow relevant instr uctions in the engine manual fo r this. • Service the engine with gasoline as instruct ed in the engine m anual. Before Starting Mow er • Attach spark plu g wire to spark plug.
11 SECTION 6: MAINTAINING YOUR LAWN MOWER Cleaning Mower The underside of th e mower deck should be cleaned after each use to preven t any build-up of grass clippings, leaves, dirt , or other debris. If this debris is allowed to accumu late, it will result in rust and corrosion.
12 Engine • Follow the engine manu al instructions and recommended schedule for lubricat ing engine components. Blade Care • Periodically inspect the blade adapter and pulley for cracks, especially if yo u strike a fore ign object. Replace when necessary.
13 SECTION 7: SERVICE & ADJUSTMENTS Replacing Drive Belt • Remove two shoulder screws securing th e front drive cover to the mower de ck. See Figure 11. Figure 11 • Press inward o n the sides of the front drive cover and releas e the tab s that secu re the fro nt drive cover to the height adjuster bracket s.
14 Figure 14 • Reassemble t he upper hand le to the lo wer handle. • Place the hairpin clips in the inner holes of th e weld pins and replace th e carriage bolts and wing nuts on the handle bra c kets. Attach the starter r ope as instructed in the Assembly section.
15 SECTION 9: TROUBLE-SHOOTING NOTE: For repairs beyond t he minor adju stments liste d abov e, cont act your local authorized se rvice dealer. Pr oblem P ossible Cause Corrective Action Engine fails to start 1. Blade control handle disenga ged 2. Spark plug wire disconnected 3.
16 19 75 28 55 53 43 54 52 66 49 28 48 6 74 73 20 72 71 3 11 4 5 2 23 34 31 70 35 29 30 37 56 67 40 24 57 51 61 45 44 42 63 36 38 28 26 32 27 64 39 22 46 8 21 16 7 50 28 25 68 15 17 65 47 14 18 13 1 62 60 59 58 9 10 33 41 69 12 SECTION 10: PARTS LIST FOR MODELS 466 & 469 IMPORTANT: For a proper working machine, use Factory Approved Parts.
17 Models 466 & 469 Ref. No P art N o. Description 1. 747-1214 Lower Bail Handle 2. 710-0599 TT Screw 1/4-20 x 0.5 3. 736-0270 Bell Washer.265 x 0.75 4. 17032A Deflector Chute Adapter 5. 732-1014 Torsion Spring 6. 731-04204 Deluxe Bail Cover 7. 747-1161A B lade Control Handl e 8.
18 NOTES.
19 NOTES.
20 MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purch ased and used in the United States, its possessions an d territories.
デバイスTroy-Bilt 469の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Troy-Bilt 469をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTroy-Bilt 469の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Troy-Bilt 469の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Troy-Bilt 469で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Troy-Bilt 469を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTroy-Bilt 469の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Troy-Bilt 469に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTroy-Bilt 469デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
