Troy-Biltメーカー500 seriesの使用説明書/サービス説明書
ページ先へ移動 of 29
Printed in U.S .A. FORM NO . 772C0708 (7/2004) IMPOR T ANT : Read saf ety r ules and instructions MTD Products Ltd., P. O. BOX 13 86, KITCHENER, ONTARIO N2G 4J1 carefully bef ore operating equipment.
2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Manu al is an important part of your new snow throw er. It will help you to assemble, prepare and maintain the unit for best performance.
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out importan t safety instruct ions which, if n ot followed, could en danger the personal safety and/or property of y ourself and others. Read and follow all instructions in this manual be fore attempting to operate this machine .
4 odorless and dead ly gas. 6. Do not operate machine wh ile und er the influence of alcohol o r drugs. 7. Muffler and engine become hot and can cause a burn. Do not touc h. 8. Exercise extreme caution when operating on or crossing gravel surfaces. Stay alert for hidden hazards or traffic.
5 SECTION 2: SETTING UP YOUR SNOW THROWER NOTE: The snow throwe r is shipped with oil and WITHOUT GASOLINE. After assembly , refer to separate engine manual for proper fuel an d engine oil recommendations. NOTE: This Operator’s Manual covers several models, handle panels, lights and ch ute cranks are some features tha t may vary by model.
6 3. One end o f each chute ke eper is already at tached to the chute fla nge. Pivot the free end of the chute keeper to align it with the ch ute flange and push it till it snaps into posit ion. See Figure 4. Repeat with remaining chut e keepers. Figure 4 For Models with 4 Wa y Chute Control Box 1.
7 Auger Control Test 1. To check the adjus tment of the auger control, push forward the left han d control until the rubber bumper is compressed. There should be slack in the cable. 2. Release th e control. The cable should be straig ht. Make certain you can depress the auger cont rol grip against the left handle completely.
8 1. Adjust skid sh oes by lo osening th e four hex nuts (two on each side) an d ca rriage bolts. Move skid shoes to desired position. 2. Make certa in the entire bot tom surface of skid shoe is against the ground to avoid un even wear on the skid shoes.
9 IMPORT ANT : Always release the drive control before changing speeds. Auger Control The auger cont rol is located on the left handle. Squeeze the aug er control to engage the augers. Release to stop the snow throwin g action. T he drive co ntrol must also be released in order to sto p the auger.
10 (inside the boot) i s fastened securely over the metal tip on the sp ark plug. • Make certain bot h the auger control and drive control are in the disenga ged (released) position. • Move throttle con trol up to FAST position. Insert ignition key into slot.
11 against the star ter. 3. If the engine still fails to start, repeat the first two steps. If continued attem pts do not free starter, follow the el ectric starte r proced ures to sta rt. 4. Avoid freezin g of the recoil starter by referring t o instructions below.
12 • If for some re ason, you have to operate the snow thrower on gr avel, keep the skid shoe in the highe st position for maxim um clearance between ground and shave plate.
13 Figure 14 Check V -Belts Follow instructions below to check the cond ition of the drive belts every 50 hours of oper ation. 1. Remove the plastic be lt cover on the front of the engine by removing two self-ta pping screws. 2. Visually inspect for frayed, cra cked, or excessively worn out belts.
14 Shave Plate and Skid Shoes The shave plate and skid shoe s on the bottom of the snow throwe r are subje ct to wear. Check the se periodically and replace as nece ssary. Replacing Skid Shoe 1. Remove four carriage bolts an d hex nuts which attach two skid shoes to th e s no w t hr ow er on t wo sides.
15 9. Re-install frame cover and flip the snow thrower back to the o perating position. 10. W rap auger be lt around the engin e pulley. 11. Re-insta ll belt co ver with se lf-tapping s crews removed be fore. Drive Belt 3. * Push idler counter-clock wise and insert a Philips head screwdrive r in the hole on t he idler as shown in Figure 20.
16 . Figure 23 Figure 24 9. Reassemble new frictio n wheel rubber to the friction wheel assembly, tighte ning the four screws in rotation and wit h equal force. See Figure 24. IMPORT ANT : Assemble the rubb er on the friction whee l equally for proper functioning.
17 See Figure 26C. 4. Thread th e ferrule up or down the shift ro d as necessary until the fe rrule lines up with the upper hole in the shift lever . See Figure 26B. 5. Insert fer rule into th e upper h ole in shift le ver as shown in Figure 26B. 6. Reinstall the hairpin clip.
18 SECTION 7: TROUBLESHOOTING NOTE: This se ction addresses minor service issues. For furt her details, contact an authorized service center for assistan ce. Prob lem Cause Remedy Engine fails to start. 1. Fuel tank empty, or stale fu el. 2. Blocked fuel lin e.
19 SECTION 8 : TWO YEAR LIMITED WARRANTY For TWO YEARS from the date of re tail purchase within Canada, MTD PR ODUCTS LIMITE D will, at its option, repair or replace, fo r the original purchaser, free of charge, any part or parts found to be defective in material or workmanship .
20 43 41 41A 41B 41C 42 42A 42B 42D 42E 42F 42G 42C 42H 42I 42J 42K 43A 43B 43C 43D 43E 43F 66 67 65 64 63 48 70 47 56 55 53 55 54 52 51 50 49 60 59 58 57 56 2 1 30 42 41 43 34 35 33 6 45 18 1 4 69 68.
REF PA R T NO . NO. N° DE N° DE RÉF PIÈCE DE SCRIP TION DE SCRIP TION 1 710-0896 Hex B-Tap Scr 1/4-28 x .25" Lg Vis taraudée à tête hexagonale 1/4-28 x 0,25 2 731-04792 Belt Cover Couvre-c.
REF PA R T NO . NO. N° DE N° DE RÉF PIÈCE DE SCRIP TION DE SCRIP TION 50 712-04064 Hex L-Flanged Nut 1/4-20 Gr. F Ny lon Contre-écrou à embase 1/4-20 Qual.
23 NOTES.
24 51 58 57 47 44 58 53 54 62 61 63 66 68 65 67 59 46 41 42 43 44 50 49 45 48 2 39 37 37 40 32 2 33 34 9 31 30 29 1 8 5 7 25 23 24 2 20 19 18 26 21 17 16 15 64 60 37 6 4 3 2 2 10 13 12 14 34 28 15 70 .
REF PA R T NO . NO. N° DE N° DE RÉF PIÈCE DE SCRIP TION DE SCRIP TION 1 731-04425 Up per Chute Goulotte supérieur 2 712-04063 Flange Locknut 5/16-18 Gr.
26 AUGER HOUSING COM PO NENTS/ COMPOSANTS DU LOGEMENT D ES TARIÈRE S SIZE TAILLE AU GER HOUS ING/ LOGEMENT DES TARIÈRES AU GER AXLE/ ESSIEU DES TARIÈRES SHAVE PLATE LAME PLATE GEAR BOX ASS’Y/ EN .
27 NOTES.
28 41 42 40 39 38 37 52 50 49 48 51 46 47 25 24 27 26 23 31 28 45 17 1 2 3 4 7 8 5 44 15 14 13 12 *55 29 30 35 34 10 18 19 20 22 21 A 53 B B A 36 11 57 54 54 16 58 58 *60 *61 *62 *63 59 *56 11 *55 9 9* * With heated grips only/Av ec poignées chauffées seulement.
REF PA R T NO . NO. N° DE N° DE RÉF PIÈCE DE SCRIP TION DE SCRIP TION 1 684-04106A En gage ment Han dle As sem bly RH Poignée d’entraînement CD 2 746-0778 “Z” Fit ting Extrémité en «Z».
デバイスTroy-Bilt 500 seriesの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Troy-Bilt 500 seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTroy-Bilt 500 seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Troy-Bilt 500 seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Troy-Bilt 500 seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Troy-Bilt 500 seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTroy-Bilt 500 seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Troy-Bilt 500 seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTroy-Bilt 500 seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
