Troy-Biltメーカー52057の使用説明書/サービス説明書
ページ先へ移動 of 24
GARDEN WAY INCORPORATED OWNER’S MANUAL T rimmer/ Mower • Safety • Assembly • Features/Controls • Operation • Maintenance • Parts List Models 52057 – 5 HP Recoil Star t 52058 – 6HP Electric Star t (Electric Start Model Shown) $4 .
SECTION 1: SAFETY ...........................................1 General Operation ......................................................1 Slope Operation .........................................................2 Children...............................
1 Under California law, and under the laws of several other states, you are not permitted to operate an internal combustion engine using hydrocarbon fuels on any forest covered, brush covered, or gras.
2 Section 1: Safety 20. Always wear approved safety gog- gles or safety glasses with side shields when operating equipment. The use of any powered machine can result in for- eign objects being thrown by high- speed rotating parts which can cause personal injury or property damage.
3 Section 1: Safety and debris shield. Make sure they are not ben t, dam age d, o r loose. 10. Only use eighteen-inch long .130" or .155" diameter trimmer line. N ever use other lengths, diameters or material as trimmer line. 11. Trimmer line moves at high speed and can cut.
4 Introduction Carefully follow these assembly steps to correctly prepare your machine for use. It is recommended that you read this Section in its entirety before begin- ning assembly. NOTE: If an assembly step applies only to certain models, those models are noted at the beginning of that step.
5 Section 2: Assembly Figure 2-2: Handlebar installation (electric start model shown). A C D F E B G F O M M Figure 2-4: Check trimmer head hard- ware for tightness. 5. Use two cable ties (F, Figure 2-2) to secure the trimmer head control cable (C) and the electrical wiring har- ness (O) to the handlebar at the loca- tions shown.
6 Section 2: Assembly STEP 6: Connect and Charge Battery (Electric Start Models) 1 . Lift and tilt debris shield (X, Figure 2-5) forward to view battery (P). Connect the red wire (R, Figure 2-6) to the positive (+) red-coded terminal on the battery. Then, connect the black wire (S) to the negative ( – ) black- coded terminal on the battery.
7 Features and Controls 3 Section Operating Symbols Various symbols (shown here, with word descrip- tions) are used on the unit. STOP FEA TURES AND CONTROLS This Section describes the location and function of the features and controls on your machine.
8 PRE-ST ART CHECKLIST 1. Review Section 1: Safety and also Section 3: Features and Controls. 2. Check for loose or missing hard- ware. Tighten or replace as needed. 3. Check the engine oil level*. It must be up to the “ FULL ” mark on the oil dipstick.
9 Section 4: Operation USE THE CORRECT DIAMETER TRIMMER LINE Before starting a project, examine the grass or material you will be cutting and trimming. For tougher conditions, use two (or four) sections of the thicker gauge, .155" diameter extra-heavy duty line.
10 Tips for Precision Cutting For the most precise cutting possible, be sure to select the appropriate line cutting height and trimmer line size (thickness) for the conditions at hand. When mowing, let the cutting head rest lightly on the ground and do not lift up on the handlebars.
11 ADJUSTING TRIMMER HEAD ENGAGEMENT The tension on the drive belt must be correct for proper operation of the trimmer head. If the tension is correct, the trimmer head will rotate when the Trimmer He.
REMOVING AND REPLACING THE TRIMMER HEAD 1. Stop the engine and wait for all moving parts to stop. Disconnect spark plug wire and move it away from the spark plug. Remove the ignition key on electric start models. 2. Two bolts (A, Figure 5-3) secure the trimmer head (B) to the spindle head (C).
13 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models.
14 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage.
15 Section 5: Maintenance damage caused by overspeeding. Do not tamper with the governor settings. Seek authorized service if you think an adjust- ment is required.
16 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models.
17 Section 5: Maintenance PROBLEM POSSIBLE CAUSE CORRECTION Engine does not start. 1. Spark plug wire disconnected. 1. Reconnect wire. 2. Defective or incorrectly gapped spark plug. 2. Inspect/replace spark plug. 3. Fuel tank empty. 3. Add fuel. 4. Dirty carburetor or fuel line.
18 Parts List Models 52057 & 52058 DRA WING NO. 1 1 2 3 4 5 5 5 5 5 5 7 8 9 10 11 12 13 17 17 17 16 20 21 22 23 24 25 15 18 19 14 14 6 6.
19 Models 52057 and 52058 Parts List 1 1917765 Debris Guard ............................................ 1 2 1918082 Decal-Logo (B) ......................................... 1 1904401 Decal-Logo (A) ......................................... 1 3 1915290 Push-in Fastener .
20 Parts List Models 52057 & 52058 DRA WING NO. 2 See DRAWING NO. 1 See DRAWING NO. 3 See ACCESSORIES AND KITS 2 2 1 1 3 3 4 7 8 9 10 11 12 13 14 15 16 27 17 18 22 23 24 25 26 18 18 19 20 21 6 1 1917778 Wheel/Tire Assembly ........................
21 DRA WING NO. 3 1 4 5 2 3 6 6 8 7 9 12 13 13 13 14 15 16 14 10 11 1 1918283 Upper Handlebar (Incl. Refs. 2 & 3) ....... 1 2 1915889 Decal – Bail Engage/Disengage ................ 1 3 1918304 Decal – Throttle .................................
CUSTOMER SERVICE INFORMA TION Owner Registration Card Please fill out and mail the enclosed owner registration card. The purpose of this card is to register each unit at the factory in order to keep the owner informed with informational bulletins and safety literature.
デバイスTroy-Bilt 52057の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Troy-Bilt 52057をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTroy-Bilt 52057の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Troy-Bilt 52057の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Troy-Bilt 52057で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Troy-Bilt 52057を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTroy-Bilt 52057の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Troy-Bilt 52057に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTroy-Bilt 52057デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。