Troy-Biltメーカー634FMの使用説明書/サービス説明書
ページ先へ移動 of 32
O TRO_ BILT Operator's Manual Rear-tine Tiller Models 630C Tuffy _ 634Fm BroncoTM 634Bm Super BroncoTM Model 634B Shown IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY WARNING: This unit .
TABLE OF CONTENTS Content Page Calling Customer Support ....................................................................................................... 2 Safety ..................................................................................
SECTION 1: SAFETY This machine meetsvoluntary safety stan- dard B71.8-1996, whichis sponsored bythe Outdoor PowerEquipment Institute, Inc., and is published bythe AmericanNational Standards Institute.
4. Exercise caution to avoid slipping or fall- If in doubtabout the tilling conditions,al- 24. Do not touch engine parts which may ing. 5. If the unit should start to vibrate aonor- really,stop the engine, disconnect the spark plug wire and prevent it from touch- ing the spark plug, and check immediately for the cause.
Decals For your safety and the safety of others, vari- ous safety and operational decals are located on your unit (see Figure 1-2) t Keepthe decals clean and legible at all times. Contactyour local service dealer or the factory for replacements if any decals are damaged or missing.
SECTION 2: ASSEMBLY WARNING: To prevent personal injury or property damage,do not start the engine until all assembly steps are complete and you have read and understandthe safety and operating instructions in this manual. INTRODUCTION Carefully follow these assembly steps to correctly prepare your tiller for use.
Fig. 2-3: Wheel in FREEWHEEL position STEP 4: INSTALL FORWARD CLUTCH CABLE 1. Attach the forward clutch cable bracket (P, Fig. 2-4) to the handlebar support AI with a 1/4"-20 x 1-1/42 hex hd. screw (R) and V4"-20 hex Iocknut (S). Tighten se- curely.
4. Thread the #10-24 hex nut (Z, Fig. 2-5) halfway onto the screw (V). 5. Thread the screw IV_ into the cable ad- juster (X). 6. Hook the cable spring (W, Fig.2-6) into the V-shaoed bend in the Forward Clutch Bail _Y). 7. Check for correct tension on the forward drive belt by taking two measurements of the cable spnng, as follows: a.
31bY I_: L;I'IEL;K LEVEL UI- The transmission was filled with gear oil at the factory. However,you should check the gear oil level at this time to makecertain it is correct. IMPORTANT: Do not operate the tiller if the gear oil level is low. Doing so will result in severe damage to the transmission com- ponents.
SECTION 3: FEATURES AND CONTROLS WARNING: Before operating your machine, carefully readand understand all safety, controls and operating instructions in this Manual, the separate Engine Owner's Manual,and on the decals on the machine. Failure to follow these instructions can result in serious personal injury.
Figure 3-3: FREEWHEEL position. ,_ WARNING: Use extreme caution when reversing or pulling the machine towards you. Look behind to avoid obstacles. Neverattempt to till in reverse. Failure to follow this warning could result in personal injury or property damage.
SECTION 4: OPERATION WARNING: Before Reverse Clutch Control operating your machine, (Models 634F/634B) carefully readand understand all safety (Section 1), controls (Section 3) and operating instructions (Section 4) in this Manual, the separate Engine Owner's Manual,and on the Clutch Bail decals on the machine.
KEEP AWAY F_OM ROTATING 11NES. ROTATING 11NE$ WILL CAUSE INJURY. Stopping the Engineand Tiller 1. To stop the wheels and tines, release the Forward Clutch Bail (all models) or the Re- verse Clutch Control (Models 634F and 634B) -- whichever control is in use.
TILLING TIPS & TECHNIQUES Tilling Depths _=i, WARNING: Before A _ • tilling, Contactyour ,m = === telephone or utilities company and inquire if underground equipment or lines are used on your property. Do not till near • Avoid pushing down on the handlebars in an attemptto force the tiller to dig deeper.
TILLING TIPS & TECHNIQUES (CON'T) PowerComposting Power composting simply means tilling underand burying in the soil all manner of organic WARNING: When power matter such as crop residues, leaves, grassclippings and cover crops.
TILLING TIPS & TECHNIQUES (CON'T) Terrace Gardening(continued) • To create aterrace, start at the top of the slope and work down. Go backand forth across the first row as shown in Fig.4-10. • Eachsucceedinglowerterraceisstartedbywalkingbelowtheterraceyou'repre- e_ll_l___.
SECTION 5: MAINTENANCE ,_ WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric Start models.
WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage.
WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage.
WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage.
WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage.
WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage.
SECTION 6: MODELS 630C, 634F & 634B PARTS LIST 5 19 14 13 _ H 3 4 15 11 REF PART NO. NO. 1 1185469 2 710-0597 3 710-0599 4 710-0874 5 710-3039 6 712-0291 7 712-3004A 8 712-3009 9 736-0119 10 GW-55013-1 11 GW-55013-2 18 12 15 (A) For Model 630C (B) For Model 634F (C) For Model 634B DESCRIPTION Spiro] Pin Hex Hd.
MODELS 630C, 634F & 634B 2 20 13 18 / 2O / 16 22 25 7 20 / 18 24.
MODELS 630C, 634F & 634B REF NO. 1 1916719 2 1916755 3 1917479 4 1918745 5 710-0599 6 710-3008 7 712-3009 8 GW-55042 9 GW-55043 10 GW-55102 11 GW-55044 12 GW-9855 13 725-0157 14 736-3050 15 1916674 16 1916712 17 710-0106 18 710-0216 20 710-0805 21 712-0121 22 712-0291 23 712-3000 25 736-0119 PART NO.
MODELS 630C, 634F & 634B 1 3 / / (A) For Model 6300 (B) For Model 634F (C) For Model 634B REF NO. 1 GW-9517 2 GW-1714 3 GW-50043 4 711-04109 5 GW-1224-1 * GW-1224-2" GW-1224-3" GW-1224-4" -- GW-13250 PART NO.
MODELS 630C, 634F & 634B FRONT 8 11 3 4 (A) For Model 6300 (B) For Model 634F (C) For Model 634B _2 REF PART NO. NO. 1 GW-9512 2 1909950 3 GW-1166-1" GW-1166-2 * GW-1166-3 * GW-1166-4 * GW-11.
MODELS 630C, 634F & 634B 10 10 14 * included with transmission when purchased as an assembly only. Remove anddiscard when installing the transmission on tiller. REF PART NO. NO. 1 GW-9727 2 710-04049 3 736-0119 4 1918377 5 1916641 6 GW-50032 7 714-04030 DESCRIPTION Plug, Transmission Oil Fill Hex Hd.
MODELS 6300,634F & 634B Hold Tines With Blunt End Toward You LEFT-HAND TINE RIGHT-HAND TINE NOTE: Ideotib Left and Right sides of tiller b, standing _n operator position and facing direction of forward trave 11 2 7 t Used on Left side of tiller $ Used on Right side of tiller REF PART NO.
MODELS 630C, 634F & 634B 24 38 17 5 24' 3O.
MODELS 630C, 634F & 634B REF NO. 1 2 3 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 PART NO.
TROY-BILT TILLER LIFETIME LIMITED WARRANTY WHATPRODUCT ISCOVERED All Troy-Bilt branded rear tine walk-behind tillers with gear drive transmissions. This warranty begins on the date of purchase and is warranted by Troy-Bilt LLC for the life of the tiller, to the odgina] purchaser only.
デバイスTroy-Bilt 634FMの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Troy-Bilt 634FMをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTroy-Bilt 634FMの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Troy-Bilt 634FMの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Troy-Bilt 634FMで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Troy-Bilt 634FMを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTroy-Bilt 634FMの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Troy-Bilt 634FMに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTroy-Bilt 634FMデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
