Troy-Biltメーカー654Jの使用説明書/サービス説明書
ページ先へ移動 of 32
D 0 7 7 4 9 A C Oper ator’ s Man ual Rear-tine Tiller 654J—Thoroughbred ™ PRINTED IN U.S.A. 769-01146.fm (3/17/2004) FORM NO. IMPORT ANT : READ SAFETY RULES AND INSTRUCTIONS CAREFULL Y WARNING: .
2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Manu al is an important part of your new rear-tine tiller. It will help yo u assemble, prepar e and maintain the unit for best performance.
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out import ant safety instructions which , if not followed, could endanger the personal safe ty and/or property of yourself and other s. Read and follow all instr uctions in this manual before attemptin g to operate this machine .
4 8. Before cleaning, repair ing, or inspecting, stop the eng in e and make certain all moving pa rts ha ve stopped. 9. Always keep the tiller’s rear tine shield down. 10. Never use the tiller unless proper guards, pl a te s , o r other safety protective devices ar e in place.
5 SAFETY LABELS FOUND ON YOUR TILLER W A R NING Hot surfaces can cause severe burns. Do not touch muffler or adjacent areas. S30647 WARNING TO AVOID SERIOUS INJURY 1. READ THE OPERATOR'S MANUAL. 2. KNOW LOCATION AND FUNCTIONS OF ALL CONTROLS. 3. KEEP ALL SAFETY DEVICES AND SHIELDS IN PLACE AND WORKING.
6 SECTION 2: ASSEMBLING THE TILLER NOTE: All referenc es to th e RIGHT o r LEFT sid e of the tiller are observed from operator’s position. T ools Needed for Assembly • 9/16” Wrench (Handle Mount.
7 Attaching the Control Box 5. Remove the four Phillips screws and lock nuts from the control box plate. 6. Insert the en ds of the two springs into the holes found in the control levers located on t he underside of the handle pane l.
8 Attaching the Shift Cable 8. Place the shift lever in th e forward position. Insert the end of the shift cable in to the hole in shift lever located on the underside t he handle panel. 9. Position the shift cable’s threaded adjuster in the slot found on the s hift lever moun t bracket.
9 SECTION 3: KNOW YOUR TILLER Read this operat or’s manual and safety rules before operating your tiller. Compar e the illustrations above with your unit to familiarize yourse lf with the location of various controls. Save th is manual for futur e reference .
10 Tine Direction Selector The tine direction selecto r (found in the lower left area the handle panel) is used to alternate tine rotation bet ween FRT mode (Forward Rotating Tines) to CRT mode (Counter Ro tating Ti nes). • Operate the tiller in CRT mode when tilling virgin ground, sod or hard soil.
11 SECTION 4: OPERATING YOUR TILLER WARNING: Read, understand, and follow all instructions and warnin gs on the machine, in this manual and the Briggs & Stratton Owner/ Operator manu al packed with your unit before operating the tiler.
12 Stopping Engine • Move throttle control leve r to STOP position. See Figure 1. Figure 1 CAUTION: Never sto p the engine by movi ng the choke lever into the CH OKE position.
13 Preparing Seedbeds Tilling wet soil often results in large, hard clumps of soil that can inter fere with plant- ing. If time permits, wait a day or two after heavy rains to allow the s oil to dry before tilling. T est soil by squeezing it into a ball.
14 Tilling On Slopes Read the following recomm endations before tilling on slopes: If you must garden on a moderate slope, please follow two ver y important guidelines: 1. Till only on moderate slopes, never on steep ground where footing is difficult (review safe - ty rules in Section 1 : Safety of this manual).
15 SECTION 5: MAINTENANCE AND ADJUSTMENTS WARNING: Before perf orming any maintenance, or repa irs, turn the engine off and allow it to cool, move th e tiller to a level surface, place the wheel shift lever in the FORWARD position and chock the tiller’s wheels.
16 Ignoring a leak can result in severe tran smission dam age. If a cover leaks, try tightening any loose screws or bolts. If the fasteners are tight, a new gasket or oil seal may be required. If th e leak is from around a shaft and oil seal, t he oil seal probably n eeds to be replaced.
17 Shift Cable If the tiller’s wheels do not “freewheel” when the wheel shift lever is in the NEUTRAL po sition, the shift cable is in need of adjustmen t.
18 SECTION 6: SERVICE Changing the Belts WARNING: Position the tiller on flat, level surface, chock th e wheels, shut the engine off and allow it to cool befo re removing the be lt(s). All belts on your tille r are subject to we ar and should be replaced if any signs of wear are present.
19 4. Begin th e removal the rever se tine belt as follows: a. Apply pressure on the idler pulleys to relieve tension on the r everse tine cable and th e wheel drive cable. b. Carefully unhook each cable-end . 5. Unloop the whee l drive belt from around the engine pulley.
20 Wheel Drive Belt NOTE: The wheel drive belt is under the least amount of load and will wear at a sl ower rate. It may not be necessary to re place the wheel dr ive belt as often a s the tine belts. In spect the belt and read the following steps before proceeding .
21 Tines The tines will wear with use and should be inspected at the beginning of each tilling season and after every 30 operating ho urs. WARNING: Position the tiller on flat, level surface, chock th e wheels, shut the engine off and allow it to cool before inspecting or removing the ti nes.
22 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTION Engine does not start 1. Spark plug wire disconnected. 1. Reconn ect wire. (See E ngine Owner’ s Manual) 2. Engine Throttle Control L e ver incorre ctly set. 2. Put lever in ST ART position. 3. Fuel tank em pty .
23 8 7 3 12 10 11 2 17 18 9 6 13 15 16 14 1 5 4 Wheels and Tines REF NO. P ART NO. DESCRIPTION 1 642-04015 Adapter Assembly, Tine 2 712-3054 Nut, 3/8-24, Hex, Lock 3 736-0169 Washer, Lock, 3/8, Regular Duty 4 736-0208 Washer, Flat, .51 x 1.5 x .07 5 736-0253 Washer, Bell, .
24 A A B C C D D B 2 2 8 1 13 17 34 17 30 27 19 29 14 14 9 18 11 13 36 3 25 22 38 26 22 12 13 23 20 37 22 13 35 20 5 6 28 15 4 13 26 22 31 32 16 13 13 10 10 Handlebar and Controls.
25 Handlebar and Controls REF NO. P ART NO. DESCRIPTION 1 647-04026 Bail Assemb ly, Control, Wheel 2 649-04014 Handle Assembly, Loop 3 686-04038 Lever Assemb ly, Control, Tine 4 686-04040 Lever Assembly, Pivot 5 710-3119 Hex Screw, 3/8-16, .75, Gr5 6 710-04198 Screw, Carriag e, 3/8-16, 6.
26 A B C D D E F G G F E C 8 Wheel Clutch Cable (Shown for Reference) Forward Tine Clutch Cable (Shown for Reference) Reverse Tine Clutch Cable (Shown for Reference) 22 6 20 23 25 21 44 30 33 37 26 39.
27 Drive System REF NO. P ART NO. DESCRIPTION 1 686-04034 Bracket Assembly, Clutch 2 710-0117 Hex Screw, 5/16-24, 1.00, Gr5 3 710-0378 Hex Screw, 5/16-18, 2.50, Gr5 4 710-0599 Screw, Self-tapping, 1/4-20, 0.500 5 710-0624 Hex Screw, 5/16-24, 1.50, Gr5 6 710-0642 Screw, Self-tapping, 1/4-20, 0.
28 8 55 68 9** 41*** 28 5** 38 64-67* 69 70 56 54 36 59-63* 57 27 13 51 23 19 49 37 17 25 22 17 53 39* 21 37 26 1 20 33 39 3 14 34 35 58* 42 12 40 48 47 30 10 31 53 38 36 54 59-63* 56 57 11 2 4 72 15 6 5 52 18 69 44 70 71 31 7** 50 43 51 16 7** 24 * Shims used "As Required" to obtain between .
29 T ransmission REF NO. P ART NO. DESCRIPTION 1 611-04033 Shaft Assembly, Detent 2 619-04069 Housing, Transmission 3 619-04070 Cover, Housing, Transmission 4 686-04039A Link Assembly, Shift 5 710-1880 Hex Screw, 5/16-18, .75, Gr5, Patch 6 710-0425 Screw, Machine, #10-24, 0.
30 A A 16 3 7 12 7 7 7 14 20 6 15 4 22 2 4 10 9 13 13 5 21 7 20 4 19 7 8 18 1 10 Tine Shield REF NO. P ART NO. Description 1 686-0044A Cover Assembly, End 2 710-0597 Hex Screw, 1/4-20, 1.00, Gr5 3 710-0604 Screw, Self-ta pping, 5/16-18, 0.625, 4 710-0874 Hex Screw, 5/16-18, 1.
31 NOTES.
32 TR O Y -BIL T TILLER LIFETIME LIMITED W ARRANTY WHAT PRODUCT All Troy-Bil t brand ed rear tine wa lk-behind tillers with gear drive tran smissions. IS COVERED This warranty begins on the date of p urchase and is warranted by Troy-Bilt LLC for the life of the tiller, to the origin al purchaser only.
デバイスTroy-Bilt 654Jの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Troy-Bilt 654Jをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTroy-Bilt 654Jの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Troy-Bilt 654Jの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Troy-Bilt 654Jで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Troy-Bilt 654Jを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTroy-Bilt 654Jの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Troy-Bilt 654Jに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTroy-Bilt 654Jデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
