Troy-Biltメーカー664D-Ponyの使用説明書/サービス説明書
ページ先へ移動 of 40
Operator ’ s Manual Rear-tine T iller Model 664D—Pony ® Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush - .
2 For more details about your unit, visit our website at www .troybilt.com T ABLE OF CONTENTS Content Page Calling Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety . . . .
Safety 1 Section 3 The engine exhaust from this product contains chemicals known to the State of California to cause cancer , birth defects or other reproductive harm. W A R NING This machine meets voluntary safety standard B71.8 – 1996, w hich is sponsored by the Outdoor Power Equipment Institute, Inc.
4 Section 1: Safety 7. Take all possible precautions when leaving the machine unattended. Stop the engine. Remove ignition key on electric start models. Disconnect spark plug wire and move it away from the spark plug. Move Wheel Gear Lever to ENGAGE. 8.
Section 1: Safety 5 4. To reduce the chances of a fire hazard, keep the engine free of grass, leaves, or excessive grease. 5. Store gasoline in a cool, well-venti- lated area, safely away from any spark- or flame-producing equipment. Store gasoline in an approved container, safely away from the reach of children.
Assembly 2 Section 6 INTRODUCTION Carefully follow these assembly steps to correctly prepare your tiller for use. It is recommended that you read this Section in its entirety before beginning assembly. INSPECT UNIT Inspect the unit and carton for damage immediately after delivery.
Section 2: Assembly 7 4. With the forward clutch cable (N, Figure 2-4) on the inside of handlebar, position the handlebar ends on the outside of the two mounting tabs (M, Figure 2-3) on the transmission top cover. NOTE: The curved handlebar height adjustment bracket appears as shown in C, Figure 2-3 for non-electric start units.
4. Check for correct spring/cable tension as instructed in Section 5, Checking and Adjusting Forward Clutch Belt Tension . 5. When tension is correct, tighten the two jam nuts (B) securely. STEP 5: CHECK TRANSMISSION GEAR OIL LEVEL The transmission was filled with gear oil at the factory.
Features and Controls 3 Section 9 Before operating your machine, care- fully read and understand all safety, controls and operating instructions in this Manual, the separate Engine Owner ’ s Manual, and on the decals on the machine. Failure to follow these instructions can result in serious personal injury.
10 Section 3: Features and Controls REVERSE CLUTCH CONTROL The Reverse Clutch Control (C, Figure 3-1) controls the engagement of reverse drive to the wheels and tines. The revers- ing feature is used for maneuvering the tiller only – never engage the tines in the ground while going in the reverse direction.
Operation 4 Section 11 Figure 4-1: Location of main tiller controls. INTRODUCTION Read this Section of the manual thor- oughly before you start the engine. Then, take the time to familiarize yourself with the basic operation of the tiller before using it in the garden.
12 Section 4: Operation ST ARTING THE ENGINE The following steps describe how to start and stop the engine. Do not attempt to engage the tines or wheels until you have read all of the operating instruc- tions in this Section.
Section 4: Operation 13 (b) As the tiller moves forward, relax and let the wheels pull the unit along while the tines dig. Walk behind and a little to one side of the tiller. Use a light but secure grip with one hand on the handlebars, but keep your arm loose.
14 Section 4: Operation T illing Tips & T echniques Let the tiller do the work • While tilling, relax and let the wheels pull the tiller along while the tines do the digging. Walk on the side that is not yet finished (to avoid making foot- prints in the freshly tilled soil) and lightly, but securely grip the handlebar with just one hand.
Section 4: Operation 15 T illing Tips & T echniques Clearing the tines The tines have a self-clearing action which eliminates most tangling of debris in the tines. However, occasionally dry grass, stringy stalks or tough vines may become tangled. Follow these proce- dures to help avoid tangling and to clean the tines, if necessary.
16 Section 4: Operation POWER COMPOSTING Power composting simply means tilling under and burying in the soil all manner of organic matter such as crop residues, leaves, grass clippings and cover crops. This material will decompose during the non-growing season and add important natural nutrients to the soil.
Maintenance 5 Section 17 TILLER LUBRICA TION Proper lubrication of the tiller is an essen- tial part of your maintenance program. After every 10 operating hours, oil or grease the lubrication points shown in Figure 5-1 as described below.
18 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped.
Section 5: Maintenance 19 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped.
20 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped.
Section 5: Maintenance 21 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped.
22 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped.
Section 5: Maintenance 23 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped.
24 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped.
Section 5: Maintenance 25 BUMPER — MODEL OEM-290-254 The tubular steel bumper helps to protect the engine from damage. HILLER/FURROWER — MODEL OEM-290-251 The furrower blade attaches to the back of the depth regulator assembly and is used to create rows, trenches and ditches up to 8" deep, depending on soil conditions.
26 Parts List Model 664D HANDLEBAR ASSEMBL Y and CONTROL LEVERS 10 (See page 32, Ref. 47, for attachment screw).
Parts List 27 Model 664D REF. PART No. No. DESCRIPTION QTY. REF. PART No. No. DESCRIPTION QTY. 1 1918811 Handlebars (Incl. Refs. 2, 3 & 3A) ....... 1 2 GW-9126 Grip ..................................................... 2 3 777I20938 Decal, Control Panel .
28 Parts List Model 664D ENGINE, SUPPORT BRACKETS, PULLEYS, BEL TS, BEL T COVER Reverse Clutch Cable 1 2 6 5 7 7 3 4 13 14 15 16 17 16 52 21 25 24 23 8 39 46 20 20 43 53 54 41 44 51 43 44 37 38 47 35 45 45 49 50 40 42 48 12 26 27 3 28 29 30 9 22 18 12 11 20 10 9 8 35 36 (Screw, Ref.
Parts List 29 Model 664D ENGINE, SUPPORT BRACKETS, PULLEYS, BEL TS, BEL T COVER 1 ** Engine – standard recoil start ............ 1 ** Engine – electric start ........................ 1 2 1917326 Bracket, Clutch Cable .......................... 1 3 736-0119 Lockwasher – 5/16.
30 Parts List Model 664D TRANSMISSION HOUSING, COVERS, SEALS, GASKETS, PLUGS NOTE 1: These screws are a special sealing screw that cannot be reused without risking the loss of transmission oil. If these screws are loosened or removed, they must be replaced with new screws.
Parts List 31 Model 664D MAIN DRIVE SHAFT 1 GW-1714 Bearing, Tapered Roller with Race .... 1 2 GW-20718 Spur Gear .....................................
32 Parts List Model 664D WHEEL SHAFT , ECCENTRIC SHAFT and TILLER SHAFT ASSEMBLIES REF. PART No. No. DESCRIPTION QTY. REF. PART No. No. DESCRIPTION QTY. 1 GW-9621 Oil Seal .............................................. 2 2 1909950 Retaining Ring (heavy-duty, external) 2 3 GW-1166-1 Shim, 1-1/64 I.
Parts List 33 Model 664D 1 710-3105 Hex Hd. Screw, 3/8-16 x 1-1/4* .......... 16 2 GW-1270-2A Bolo Tine-single. Right hand tine used on left side of tiller. (Incl. two ea. Refs. 1 and 3) ..................... 8 3 712-0375 Hex Locknut, 3/8-16 .........
34 Parts List Model 664D ROW MARKER A TT ACHMENT ROW MARKER ATTACHMENT – OEM-290-257 (Complete – Attaches to Furrower Attachment) MAIN SUPPORT/YOKE ASSEMBLY PART # 1904522001 DET AIL A 19 20 23 22.
Parts List 35 Model 664D ROW MARKER A TT ACHMENT & BUMPER A TT ACHMENT Row Marker Attachment (option) – OEM-290-254 1 1904522001 Main Support & Yoke Assy – complete. (Incl. Ref. No.'s 10,11,12,13,14,15,16,17 & 18).......... 1 2 GW-1594 Marker Blade – blade only .
36 Parts List Model 664D HOOD, BRACKET and DEPTH REGULA TOR 1 1917605 Tine Hood (Incl. hood flap and Ref.17) ............................................ 1 2 710-0169 Lockwasher, 3/8.................................. 2 3 GW-2527 Bracket – hood & depth regulator (Incl.
Parts List 37 Model 664D HILLER/FURROWER A TT ACHMENT HILLER/FURROWER – OEM-290-251 (Viewed from front of tiller) 1 1900771001 Furrower Blade .................................. 1 2 1186098 Carriage Bolt, 5/16-18 x 3/4 .............. 4 3 1177548 Star Washer, External Tooth, 5/16.
38 Notes.
Notes 39.
TROY -BIL T TILLER LIFETIME LIMITED W ARRANTY WHAT PRODUCT All Troy-Bilt branded rear tine walk-behind tillers with gear drive transmissions. IS COVERED This warranty begins on the date of purchase and is warranted by Troy-Bilt LLC for the life of the tiller, to the original purchaser only.
デバイスTroy-Bilt 664D-Ponyの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Troy-Bilt 664D-Ponyをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTroy-Bilt 664D-Ponyの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Troy-Bilt 664D-Ponyの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Troy-Bilt 664D-Ponyで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Troy-Bilt 664D-Ponyを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTroy-Bilt 664D-Ponyの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Troy-Bilt 664D-Ponyに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTroy-Bilt 664D-Ponyデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
