Troy-BiltメーカーOEM-390-679の使用説明書/サービス説明書
ページ先へ移動 of 19
TRACK SNOW THROWER Oper ator’ s Man ual PRINTED IN U .S.A. TR O Y-BIL T , P .O . BO X 1386, 97 KENT A VE., KITCHENER, ON N2G 4J1 (5/2005) IMPORTANT: Read safety rules and instructions carefully.
2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Manual is an important part of yo ur new snow thrower. It will help you to as semble, prepare and maintain the u nit for best performa nce.
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instruct ions which, if not fol lowed, could endange r the personal safety and /or property of your se lf and others. Read and follow all in structions in this manual before attempting to operate this machine.
4 9. Exercise caution when chan ging direction and while operating on slopes. 10. Plan your snow throwing pattern to avoid discharge towards windows, walls, cars etc. To avoid property damage or personal in jury caused by a ricoch et. 11. Never direct discharge at children, bystanders and pets or allow anyone in front of the machine.
5 SECTION 2: ASSEMBLING YOUR SNOW THROWER Loose P arts The augers are secured to t he auger shaft with two shear pins and bow tie cotter pins. If you hit a foreign object or ice jam, the snow th rower is designed so that the pins may shea r. Two replac ement shear pin s and cotter pins are pr ovided for your convenience.
6 • If not already atta ched, slip the ca bles that run fr om the handle panel to th e chute assembly into the cable guide located on t op of the engine. See Figure 4. • If not al ready attached, unwra p the headlight wir e which is attached to the he adlight, beneath the handle panel.
7 The drive control also locks the auger control so you can turn the chute dire ctional control without interrupting t he snow throwing process. If the auger control is engaged simultaneously with the drive control, the ope rator can release t he auger control ( on the left handle) and the au gers will remain engaged.
8 Fuel Shut-Off V alve (Optional Equipment) On models so equ ipped, the fuel shut -off valve, located under fuel tank, cont rols fuel-flow from the fuel tan k to the engine. Se e Figure 6. Safety Ignition Key The safety ignition key must be fully inserted and snapped in place before the unit will start.
9 WARNING: The electric starter is equipped with a gr ounded three-wir e power cord and plug and is designed to oper ate on 120 volt AC household curren t. It must be used with a prop erly grounded three- prong receptacle at all times to avoid the possibility of electric shock.
10 Auger Control Test IMPOR T ANT : Perform the following test before operating your snow thrower for the first time and a t the start of each wi nter season. Check the adjus tment of the auger control as follows: • When the aug er control is released and in the disengaged “up” position, the cable should h ave very little slack.
11 Figure 9 Operating T ips NOTE: Allow the engine to warm up for a few min utes. The engine will not develop fu ll power until it reaches operating t emperature. NOTE: The tem perature of the mu ffler and the surroun ding areas may exceed 150°F (65°C).
12 Figure 10 • With the traction control lever engaged, the frictio n wheel must contact the drive plate . See Figure 11. If adjustment is necessary: • Loosen the jam nut on the traction cable and thread the cable in or out as nece ssary. • Retighten the jam nut to secure the cable when correct adjustment is reached.
13 Figure 13 Carburetor • Minor carb uretor adjustment may be required to compensate fo r differences in fuel, temperat ure, altitude and load . • Refer to the se parate engine manual, packed with your unit, for car buretor adjustment info rmation.
14 Figure 15 To check the level of grease in the gear case, r emove the vent p lug. If your unit is equip ped with a g rease fitting , you may, if necessary, add grease using a grease gun and the gr ease fitting on the side of the gear case. IMPORT ANT : Do not overfill the gear case, s ince damage to the seals co uld result.
15 • Remove the carriag e bolts and flange lock nuts which attach the two skid shoes t o t h e s no w t hr ow er on two sides. See Figu re 16. Figure 16 • Reassemble new skid shoes with the har dware removed earlier. Make certain the skid shoes are adjusted to be level.
16 Figure 19 • Lift the auger belt from the auger pulley, an d slip belt between th e support br acket and the au ger pulley. Repeat th is step for the front auger belt. See Figure 20. • Replace both auger drive be lts by following instructions in r everse order.
17 Figure 22 Figure 23 • Position the fricti on wheel assembly up onto the pin of the shift rod assembly, an d slide the shaft through the assembly. Reassemble in re verse order.
18 SECTION 8: TROUBLESHOOTING NOTE: For repairs beyond minor adjustments listed above, cont act the local dealer. Prob lem Cause Remedy Engine fails to start. 1. Fuel tank empty, or stale fuel . 2. Blocked fuel line. 3. Choke not in ON position 4. Faulty spark plug.
19 SECTION 9: TWO YEAR SUPREME WARRANTY: For two years from date of retail purchase with in Canada, MTD PRODUCTS LIMITED will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.
デバイスTroy-Bilt OEM-390-679の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Troy-Bilt OEM-390-679をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTroy-Bilt OEM-390-679の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Troy-Bilt OEM-390-679の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Troy-Bilt OEM-390-679で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Troy-Bilt OEM-390-679を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTroy-Bilt OEM-390-679の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Troy-Bilt OEM-390-679に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTroy-Bilt OEM-390-679デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
