Troy-BiltメーカーT-106の使用説明書/サービス説明書
ページ先へ移動 of 17
Owner’s Manual • SET-UP • OPERATION • MAINTENANCE IMPORTANT Read Safety Rules and Instructions Carefully PRINTED IN CANADA OG-4003 Walk Behind Mower Model: T-106.
2 CALLING CUSTOMER SUPPORT • L OCA TE YOUR MODEL NUMBER AND SERIAL NUMBER which appears on your unit and record the information in the space provided below . IMPORTANT: You must have these numbers, along with the date and proof of purchase to receive warranty or service.
GENERAL OPERATION • Read, understand, and follow all instruc - tions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering re - placement parts.
tive and may result in personal injury through contact with the rotating blade. The blade control handle must operate easily in both directions and automatically return to the disengaged position when released. • Never operate the mower in wet grass.
self or your clothes which can ignite. Wash your skin and change clothes immediately . a) Use only an approved gasoline con - tainer . b) Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner . Always place containers on the ground away from your vehicle before filling.
6 15 º USE THIS SHEET AS A GUIDE TO DETERMINE SLOPES WHERE YOU MAY NOT OPERATE SAFELY. A CORNER OF A BUILDING FOLD ON DOTTED LINE, REPRESENTING A 15 º SLOPE OR A FENCE POST SIGHT AND HOL D THIS LEVE.
UNPACKING • Remove the lawn mower and all parts from the carton. Make certain all parts and litera- ture have been removed from the carton before the carton is discarded. CAUTION: Disconnect spark plug wire. if the wire is not equipped with a rubber boot, see separate engine manual for grounding procedure.
ATTACHING THE BLADE CONTROL CABLE • The brake cable is attached to the engine, and has a “Z” fitting on the loose end. Route the brake cable over the lower handle. Place end of cable through the hole in the control box as shown in figure 3. Push the plastic fitting until it locks into the hole in the throt - tle box.
TO CONVERT YOUR MOWER FROM A MULCHER TO A SIDE DISCHARGE MOWER • Lift mulching plug. Slide the two hooks on the side discharge deflector under the hinge pin on the mulching plug assembly .
FOR THE BEST RESULTS WHEN MULCHING: Clear lawn of debris. Be sure that the lawn is clear of stones, sticks, wire or other foreign objects which could damage the lawnmower.
• Remove the hairpin clips from the weld pins on the handle brackets. Press out on the legs of the lower handle. Remove lower han - dle from the mower . • T urn the lower handle around so the notch on the bottom of the lower handle is facing forward as shown in Figure 10.
CAUTION: Cutting grass in sandy soil condition causes abrasive wear to the blades. After prolonged use, especially in sandy soil conditions, the blade will become worn and lose some of the original shape. Cutting effi - ciently will be reduced and the blade should be replaced.
13 Engine Shroud Chart NOTE: this chart shows all the optional engine shrouds for the lawn mowers covered in this manual. To order replacement parts, please refer to the shroud and hardware applicable to your lawn mower unit.
14 2 3 4 5 6 7 8 9 10 11 12 13 8 15 16 17 18 19 20 21 22 23 24 26 27 28 29 30 32 33 34 33 36 37 38 35 46 46 45 22 20 39 40 27 21 26 19 23 24 25 41 42 43 44 38 1 14 38 1 31.
REF P ART NO. NO . N° DE N° DE RÉF PIÈCE DESCRIPTION DESCRIPTION 1 647-0004 Control Handle Guidon de la commande 2 710-1270 Oval C-Sunk Scr 1/4-20 X 1.31" Lg. Vis à tête noyée 1/4-20 X 1,31 po de lg. 3 712-0324 Hex Ins. L -nut 1/4-20 Gr . 8 Nylon Écrou hex.
16 THREE (3) YEAR LIMITED WARRANTY For three (3) years from the date of original purchase of our products, we will either repair or replace, at its option, free of charge, F.O.B. Factory or authorized service firm, any part found to be DEFECTIVE IN MATERIAL and WORKMANSHIP for the original purchaser.
17 note s....
デバイスTroy-Bilt T-106の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Troy-Bilt T-106をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTroy-Bilt T-106の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Troy-Bilt T-106の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Troy-Bilt T-106で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Troy-Bilt T-106を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTroy-Bilt T-106の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Troy-Bilt T-106に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTroy-Bilt T-106デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
