AcerメーカーRA19WAANUの使用説明書/サービス説明書
ページ先へ移動 of 36
Model ID:RA19W AANU Published by Wistron Corporation Printed in T aiwan © All rights reserved Subject to modification 04th-Sept.-2008 DBG DPBU II DBG DPBU II T able of Contents Important Safety Notice------------------------------------------------------------------------------------- 01 01.
Product Announcement: This product is certificated to meet RoHS Directive and Lead-Free produced definition. Using approved critical components only is recommended when the situation to replace defective parts. V ender assumes no liability express or implied, arising out of any unauthorized modification of design or replacing non-RoHS parts.
1.1 SCOPE This document defines the design and performance requirements for a 19W inch diagonal , flat panel monitor .The display element shall be a WXGA(1366X768) resolution TFT-LCD (Thin Film Transistor Liquid Crystal Display).16.7M color images are displayed on the panel.
1. Product Specification (continued) 1.3.1.3 Audio Jack (option) This jack shall connect the audio input from host computer. 1.3.2 Video Input Signals Video Input Signal Ranges 1.3.2.1 Video Signal Amplitudes The three video inputs consist of Red ,Green , and Blue signals, each with its own coaxial cable terminated at the monitor.
1.3.2.5 Sync Signal Loading TTL input loading shall be equivalent to one TTL input load. When logic 0 is asserted by a sync input , the maximum current source from any single monitor sync input to the driver is 1.6 mA .When logic 1 is asserted , the maximum current source from the driver to any single monitor sync input is 400 uA .
1.3.5 Controller Requirements 1.3.5.1 General Requirements The monitor shall include a controller capable of converting the analog RGB signal from a standard SXGA resolution video controller in the CPU to a signal which can be displayed on the panel.
1.3.8 Display Communications Channel The monitor assembly shall provide a display communications channel that conforms to VESA DDC2Bi hardware requirements.
1.4.5.5 Defect T erminology T able 3 gives the descriptive terms used in classifying defects. 1.5 Optical Characteristics Depends on the LCD supplier's spec.
2.1 MAIN OSD MENU Outline: The description for control function: 2 OSD Menu The description for control function: Ma i n Me nu Ic o n Sub Me nu Ic o n Sub Me nu Ite m D escr i p t i on Ad j ust m ent Range Re s et V al ue N/ A W a r m Set t he co l or t em p er at ure t o wa r m wh i t e .
2. OSD Manu (continued) 9 Go to cover page ACER X193HQ.
3.1 Packing Exploded Diagram 3. Exploded Diagram 10 Go to cover page ACER X193HQ.
3.2 Product Exploded Diagram 3. Exploded Diagram (continued) 11 Go to cover page ACER X193HQ.
S4 S5 S3 S2 S1 Use a Phillips-head screwdriver screwed the No.1~2 screws till that interface board and bracket chassis base firmly attached. (No1~2 screw size=M3x6; T orque=9~10KGFxCM). Use a Phillips-head screwdriver screwed the No.1~4 screws till that power board and bracket chassis base firmly attached.
Plug 2 lamp cables to the connectors of inverter board. T ake lamp cables out from the holes shown as the photo. Use a Hex-head and screwdriver screwed the DVI and D-SUB connectors (No.1~4 Hex Nut screws Size=M3x8;T orque=6.5 KGFxCM). 6.5 ±0.5 ±0.5 Phillips-head T orque= KGFxCM).
Stick Vista and TC003 label on the correct position the same as below photo T ake a LDPE+EPE bag to cover the LCD monitor . T ake two cushion foams; one is held the left side of LCD monitor , and another is held the right side. . Put accessories of stand, DVI cable, and user’s manual ,power cable on specific positions as photo below.
4. Assembly and Disassembly Procedures (continued) Use a Phillips-head screwdriver unscrew 4 screws to release the stand base. (No1~4 Screw Size=M4x10; T orque=12 KGFxCM). ±1 Disassemble the stand cover . P ut returned unit on a protective cushion,then remove LDPE+EPE bag.
Put the dissembled monitor closed to by myself W edge your finger between the front bezel and the panel, then pry up on the front bezel to disengage the locking mechanism.
Unplug 2 lamp cables Use a Hex-head screwdriver unscrewed 4 screws to release the DVI and D-SUB connectors (No1~4Hex Nut screws Size=M3x8;T orque=4.5~6.
Use a Phillips-head screwdriver unscrewed the No.1~4 screws to disassemble the power board. (No 1~3 screw size=M3x6; No 4 screw size=M4x8; T orque=9~10KGFxCM). Disconnect all of the cable Use a Phillips-head screwdriver unscrewed the No.1~2 screws to release the interface board.
5. T roubleshooting Does OSM display when you push PROCEED buttom. Yes No Proceed "No OSM display" section. Check if the sync signal from computer is output and if the video cable is connected normally. OK Proceed "checking the resolution change IC movement" section.
5. T roubleshooting (continued) 5.2 Nothing displays on the screen (Screen is black and colour of LED is blue.) Is backlight lit? Refer "Checki ng the backlight unit" section" OK NG Does computer output RGB video signals? OK Check OSM menu is displ ay on screen w h e ny o up u s ht h e" P R O C E E D "k e y .
5. T roubleshooting (continued) 5.2 Nothing displays on the screen (Screen is black and colour of LED is blue)continued Continue Check the 5V power supply for P305 pin 1,2,3. OK Check the I301 pin2 if voltage is 3.3V OK Failure P oint 1) Printed wir e between R 311 pin3, R410, R412, I307 pin1 is failure.
5. T roubleshooting (continued) 5.3 Checking the back light unit Is +22V supplied to inverter PWB ? (by the power board) OK NG Failure Point 1) Power board of Inverter part failure . Check the BKLT_EN signal of the DC input P301 pin 1 at TTL high level.
5. T roubleshooting (continued) 5.4 Abnormal screen for VGA Check the R, G, B video signal from computer input on P302 of video connector. OK NG Failure Point 1) No R, G, B video signals output from host computer, check computer. 2) Video signal cable disconnection .
5. T roubleshooting (continued) 5.5 Abnormal screen (For the DVI) Check the DVI video signal from computer input on P303 of DVI-I video connector. OK NG Failure Point 1) No DVI video signals output from host computer, check computer . 2) DVI Video signal cable disconnection .
5. T roubleshooting (continued) 5.6 Abnormal OSM display adjust problem Check the input TTL level whether was changed when pressed function keys on the P304 pin3, 5 (normal is high level, when push buttom, generat ed low level plus ) OK NG Failure Point 1) Function key wire disconnection .
5.7 Abnormal plug and play operation for VGA Confirm the host computer supplies DDC 2B mode. OK NG Failure Point The host machine is not communicatiog in DDC2B mode. Check the voltage on Q307 pin1 that is power DC 3.3V. OK NG Failure Point 1) Printed wire broke between Q307 pin3,D325 and P302 pin9 2) R369,R372,R363 is short or open.
5.8 Abnormal plug and play operation (For the DVI) Confirm the host computersupplies DDC 2 mode. OK NG Failure Point The host machine is not communicatiog in DDC 2 mode. Check the voltage on Q 307 pin1 that is power DC 3.3 V. OK NG Failure Point 1) Printed wire broke between VR307 pin3,D325 and P303 pin14 2) R361,R372,R363 is short or open.
5.9 Checking the interface circuit of sync signal 5.9.1 Checking the control circuit of horizontal sync pluse Check the horizontal sync signal on P302 pin13 TTL level. OK NG Failure Point Video cable is failure. Check the horizontal sync signal on I 308 pin9 TTL level.
5.10 Checking the resolution change IC movement Check +3.3V supply on I305 pin41,I308 pin1,46. OK NG Proceed " Checking the DC/DC converter circui t" sect ion. Check +1.8V supply on I308 pin 19,17,40. OK NG Proceed " Checking the DC/DC converter circui t" sect ion.
Check the 5V is output from P301 pin 5,6 OK NG Failure Point 1) Power wire disconnection. 2) Power board is failure . Check the 5V is input to I301 pin3. OK NG Failure Point 1) Printed wire broke between P301 pin 5,6 and I308 pin3. Check the 3.3V is output from I301 pin2, 4.
6.2 Realtek F/W Configuration: Step-1 Launch the utility of “ ” DebugT ool_V6.2.exe Step-3Select ISP icon. Step-4 Follow up the red square indication Select “both”,”Checksum”,”Auto”,”Page Erase”, Select “21” for Extend size.
Step-6Press button The screen will show “P ASS” Step-5 Select “64K” icon to load firmware image. There are two HEX files. Y ou only need to select “64K” to choose “X203H_AAS_F001-EMEA.hex” and “X203H_AAS_F001-EMEA_Extend.hex” will be loaded in “64~96” automatically .
PRINTER PLUG DVI EXTENDING SOCKET USB A PLUG D-SUB PLUG DVI EXTENDING SOCKET USB A SOCKET 1 Writing EDID Procedure Hardware Configuration: 1.)Connect the PRINTER PLUG of DDC FIXTURE with the printer port of Desktop PC. (Refer to figure 1) 2.)Plug USB A PLUG of DDC FIXTURE to USB socket of Desktop PC (Refer to figure 2) 3.
4. Choose "WRITE" from menu then select "Scan S/N And Write EDID And Test DDC” 5. Key in series number(22 characters) in the input column and below empty column. Press write button after key in S/N 6. When EDID was written successfully that will show below message on the screen Go to cover page 34 7.
8. BLOCK DIAGRAM PCB No. LCD Flat Panel Interface Board Flat Panel Controller DDC , Interface Board DC to AC Inverte r () Option AMP Audio 1W 2 * Speaker () Option Function Key Boar d AC IN - Host Com.
デバイスAcer RA19WAANUの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Acer RA19WAANUをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAcer RA19WAANUの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Acer RA19WAANUの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Acer RA19WAANUで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Acer RA19WAANUを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAcer RA19WAANUの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Acer RA19WAANUに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAcer RA19WAANUデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
