Turbo AirメーカーMSR-72G-3の使用説明書/サービス説明書
ページ先へ移動 of 16
T urbo air Speeds Up the P ace of Inno vation Refrigerator Freezer Installation and Operation Manual Please read this manual completely before attempting to install or operate this equipment! <Soli.
1. SPECIFICATION .......................................................................................... 2 2. SERIAL NUMBER ........................................................................................ 2 3. INSTALLATION .................
3 Turbo air 1. GOOD AIR CIRCULA TION - Be sure to avoid any partition and object which may stop the air flow. - Be sure that air space is allowed to flow the rear of the unit. Turbo air recommends that the rear of the unit would be no less than 5 inches from the wall.
4 Turbo air CLEANING 1. CLEANING ST AINLESS STEEL INTERIOR AND EXTERIOR (select models) : Damage to stainless steel finish due to improper use of cleaning products or non- recommended products is NOT covered under this product's warranty.
5 Turbo air B ASIC OPERA TION MSR-23NM MSR-23G-1 MSR-49NM MSR-49G-2 MSR-72G-3 1. Plug in and turn on the power switch located on the bottom of the top grille right side. The Display panel will be lighted and make a beep sound. The compressor will begin to run.
6 Turbo air DISPLA Y P ANEL OF REFRIGERA T OR 9 TEMPERA TURE Q .C. 8 7 6 5 4 3 2 1 FA N DOOR QUICK COOLING TEMPERA TURE ˚F TEMP . SETTING QUICK COOLING F AN RUNNING DOOR OPENING QUICK COOLING BUTTON TEMP . CONTROL BUTTON (SEE T O P AGE 7) INNER TEMP .
7 Turbo air 1. If you push the Q.C. (QUICK Cooling) button, the compressor will run continuously until D-Senser detect 14 ˚ F (-10 ˚ C) to bring down the temperature more quickly. (max.comp.run time = 120 min.) 2. If you push the Q.C. button again during QUICK Cooling mode, the compressor will return to the normal operation.
8 Turbo air 1. It displays the inside temperature. 2. Display range is 14 ˚ F to 69 ˚ F (-10 ˚ C ~ +20 ˚ C). 3. When the inside temperature is lower than 14 ˚ F, the panel will display ‘ ’. and, higher than 69 ˚ F, the panel will display ‘ ’.
9 Turbo air B ASIC OPERA TION 1. Plug in and turn on the power switch located on the bottom of the top grille right side. The Display panel will be lighted and make a beep sound. The compressor will begin to run. 2. The default temperature setting is No.
10 Turbo air DISPLA Y P ANEL OF FREEZER 9 TEMPERA TURE D.F . 8 7 6 5 4 3 2 1 FA N DOOR MANU AL DEFROST TEMPERA TURE ˚F TEMP . SETTING MANUAL DEFROST F AN RUNNING DOOR OPENING MANUAL DEFROST BUTTON TEMP . CONTROL BUTTON (SEE T O P AGE 1 1) INNER TEMP .
11 Turbo air 1. If you push MANUAL DEFROST button for 5 seconds, the Defrost will start. 2. During the Manual Defrost mode, the Up/Down button for the temperature control can not make the compressor cycle ON or OFF. 3. If you want to change the Manual Defrost mode to the normal mode, push MANUAL DEFROST button for 5 seconds.
12 Turbo air 1. It displays inside temperature. 2. Display range is -50 ˚ F to 50 ˚ F (-45 ˚ C ~ +10 ˚ C). 3. When inside temperature is lower than -50 ˚ F, the panel will display ‘ ’. and, higher than +50 ˚ F, the panel will show ‘ ’. 1.
13 Turbo air BEFORE REQUESTING SER VICE SYMPT OMS CA USES SOLUTIONS Freezer is melting f ood. The unit does not refrigerate at all. The unit does not refrigerate well. There is a loud noise. There are dew-dr ops on the unit exterior . There are dew-dr ops on the unit interior .
14 Turbo air MANUF A CTURING COMP ANY Turbo air warrants to the original purchaser of every new-Turbo air refrigerated unit, the cabinet and all parts thereof, to be free from defects in material or w.
15 Turbo air WHA T IS NO T CO VERED BY THIS W ARRANTY Turbo air’s obligation under warranty is limited to either repair or replacement of parts, subject to the additional limitation s below. This warranty neither assumes nor authorizes any person to assume obligations other than expressly covered by this warranty.
Warranty Claims... All claims for parts or labor must be made directly thorough Turbo Air. All claims should include: model number of the unit, the serial number of the cabinet, proof of purchase, date of installation, and all pertinent information supporting the alleged defect.
デバイスTurbo Air MSR-72G-3の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Turbo Air MSR-72G-3をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTurbo Air MSR-72G-3の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Turbo Air MSR-72G-3の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Turbo Air MSR-72G-3で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Turbo Air MSR-72G-3を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTurbo Air MSR-72G-3の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Turbo Air MSR-72G-3に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTurbo Air MSR-72G-3デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。