TVS electronicsメーカーMINI THERMAL RP-3180の使用説明書/サービス説明書
ページ先へ移動 of 19
RP-3180 MINI Thermal Printer USER'S MANU AL MANUAL REVISION V8.1 TVS Electronics Limited.
You must use the supplied adapter only . It is dangerous to use other adapters. Make sure the printer power is off before plug or unplug the cable. Please don t place the printer in humidity or dusty space, excessive humidity and dust may damage it. Do not put foods or drinks on the printer, in case that splash into the printer .
INTRODUCTION WARNING Some semiconductor devices are easily damaged by static electricity. You should turn th e printer"OFF", before you connect or remove the cables on the rear side, in order to guard the printer against the static electricity.
Chapter 1. Setting up the Printer Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. 1-1. Unpacking RP-3180 Operator s M anual Or Power cord Roll paper 01 AC Adapter Cable 1-2. Installing the printer Avoid locations in direct sunlight or subject to excessive heat.
Chapter 2. Connecting the cables 2-1. Connecting the AC Cable NOTE:T o remove the DC cable connector , make sure that the power supply s power cord is unplugged; then grasp the connector at the arrow and pull it straight out. 2-2. Connecting the AC adapter to the printer You can connect up the three cables to the printer .
Chapter 3. Installing the roll paper 3-1. Installing or Replacing the Paper Roll 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper roll cover by pressing the cover-open button. 3. Remove the used paper roll core if there is one.
07 Chapter 4. The self test The self-test checks whether the printer has any problems. If the printer does not function properly , contact your dealer. 1. Make sure paper roll has been installed properly . 2. T urn on the power while holding down the FEED button.
Chapter 7.Interface 09 Drawer Connector RS-232C Cable Connection Interface Connector Serial Interface (RS-232) (F.G) (TXD) (RXD) (DSR) (DTR) (S.G) PRINTER SIDE(25P) HOST SIDE(9P) Pin No 1 2 3 4 5 6 7 20 .
Chapter 7.Specification 11 Printing method Dot density Printing width Characters per line Character size Number of characters Print speed Paper feed speed Line spacing (default) Character structure Pa.
ESC ! N [Name] [Format] [Range] Select print mode(s) ASCII ESC ! n Hex 1B 21 n Decimal 27 33 n 0 n 255 8-2 Descriptions of Each Item [Name] [Format] [Range] [Description] [Details] [Default] [Example] The name of the command. The code sequence. Gives the allowable ranges for the arguments.
[Details] If the values of m is out of the specified range, n1 and data following are processed as normal data. The n1 and n2 indicate the number of dots of the bit image in the horizontal direction.
ESC I [Name] [Format] [Description] Select character Double-height mode ASCII ESC I Hex 1B 49 Decimal 27 73 Select character Double-height mode. ESC J n [Name] [Format] [Range] [Description] [Details].
[Default] If the horizontal length or vertical length is 0, this command is canceled and the next data is handled as normal data. If the horizontal start point + horizontal length is greater than the horizontal printable area, the horizontal printable area - horizontal start point is taken as the horizontal length.
ESC m [Name] [Format] [Description] [Details] Partial cut ASCII ESC m Hex 1B 6D Decimal 27 109 Cut the paper partially. During cutting, printing and paper feeding is stopped.
GS / m [Name] [Format] [Range] [Description] Print downloaded bit image ASCII GS / m Hex 1D 2F m Decimal 29 47 m 0 m 3, 48 m 51 Prints a downloaded bit image using the mode specified by m. Modes that can be selected by m are shown below . GS n1 n2 d1.
GS v 0 m xL xH yL yH d1...dk [Name] [Format] [Range] [Description] [Details] [Example] Printing of raster bit image ASC II GS v 0 m xL xH yL yH d1...dk Hex 1D 76 30 m xL xH yL yH d1.
For (2): n indicates the number of bar code data, and the printer processes n bytes from the next character data as bar code data. If n is outside of the specified range, the printer stops command processing and processes the following data as normal data.
29 30 RP-3180 USER'S MANUAL RP-3180 USER'S MANUAL Chapter 10. Printer Driver 10-1.How to use Logo Download T ool RP-3180 receipt printer supports Store Logo printing. You can download max four images into printer and select which one to print on receipt.
2) After install the software successfully , open [Printing Preferences...]. 3) Open [Printing Preferences...]and [Advance] to go to Advanced Options. Now, you can reset the Document Options by select the right items. See Pic 10.2-4. 31 32 RP-3180 USER'S MANUAL RP-3180 USER'S MANUAL 10-2.
デバイスTVS electronics MINI THERMAL RP-3180の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
TVS electronics MINI THERMAL RP-3180をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTVS electronics MINI THERMAL RP-3180の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。TVS electronics MINI THERMAL RP-3180の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。TVS electronics MINI THERMAL RP-3180で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
TVS electronics MINI THERMAL RP-3180を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTVS electronics MINI THERMAL RP-3180の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、TVS electronics MINI THERMAL RP-3180に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTVS electronics MINI THERMAL RP-3180デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
