Tyco Electronicsメーカー4200Lの使用説明書/サービス説明書
ページ先へ移動 of 34
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 1 of 34 User Manual 3200L 32” Interactive Digital Signage T ouchMonitor 4200L 42” Interactive Digital Signage T ouchMonitor 4600L.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 2 of 34 Copyright © 2010 T yco Electroni cs. All Right s Reserved. No part of this publication may be reproduced, trans mitted, tran.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 3 of 34 T able of Content s Chapter 1 - Introduction ........................................................................... 4 Chapter 2 – Unp acking ............................
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 4 of 34 Chapter 1 - Introduction Product Description Y our new Interactive Digital Signage T ouchM onitor combines Elo T ouchSyst ems’ reliable performance with the latest developments in touch technology and display design.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 5 of 34 Chapter 2 – Unpacking Unp acking the T ouchmonitor T o unpack the touchmonitor , follow these steps: 1. The carton should be oriented in the manner according to it s labeling.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 6 of 34 Note: For your health and safety , it is strongly recommended that at least two people handle, lift, or move these touchmonitors. Handles are provided on the unit’ s back for easier handling.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 7 of 34 Chapter 3 - T o uchmonitor Installation Connector Panel & Interfaces Remove the cable cover on the bottom rear (when viewed in landscape orientation) to access the touchmonitor ’s connector panel.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 8 of 34 3200L 4200L / 4600L / 5500L T ouchmonitor Connections 1. Connect the HDMI and/or VGA video cabl es between the monitor ’s HDMI/VGA input connectors and your HDMI/VGA video source, res pectively .
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 9 of 34 Inst alling the APR or IntelliT ouch T ouch T echnology Sof tware Drivers Some software inst allation is required for your IntelliT ouch touchmonitor to work with your computer .
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 10 of 34 Install both the “USB T ouchscreen Drivers” and “APR T ouchscreen Driver” when prompted: Screenshot for Windows XP ,.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 1 1 of 34 Chapter 4 Computer Module Installation Inst allation Note: Disconnect AC power from the touchmonitor before installing the Computer Module. Installing the Computer Module while AC power is connected to the touchmonitor will damage the Computer Module.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 12 of 34 3. Use a Philips head screwdriver to remove t he Computer Module bay’ s protective plate. 4. Clear the Computer Module’ s docking connector of any debris that may have accumulated during shipment, if necessary .
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 13 of 34 6. Replace the protective plate and tighten it s thumb screw s in order to mechanically secure the computer module. Connector Panel & Interfaces T ouchMonitor & Computer Module Connections 1.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 14 of 34 Operating System Setup Windows ® 7, Windows ® XP Operating Systems The initial setup of th e operating system take s approximately 5 minutes. Additional time might be needed for different touchcomput er hardware & operating system configurations.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 15 of 34 Click Customize. The “Regional and Language Op tions” window appears. Select the Languages tab. If required, check t he boxes for “Inst all files for complex script and right-to-left languages” and “Install files for East Asian languages.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 16 of 34 Select your location from the drop-down list in the Locations pane. Click Apply , and then OK. Choosing the computer na me (Windows 7 setup only) Y ou will be prompted to enter the computer ’ s name.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 17 of 34 Inst alling the T ouch T echnology Sof tware Drivers for Elo Computer Modules with Windows XP V isit the Elo T ouchSystems website www .
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 18 of 34 Chapter 5 – Mounting Note: For your health and safety , it is strongly recommended that at least two people handle, lift, or move these touchmonitors. T wo handles are provided on the unit’ s back for easier handling.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 19 of 34 5500L: Rear VESA Mount For the 32” model: A four-hole, 400x200m m mounting pattern is provided on the rear of the monitor .
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 20 of 34 Optional S t and T o install the optional stand: Lay the monitor face-down on a table with the bottom edge flush to the edge of the t able. Mount the two “feet” from the optional st and using all of the provided screws.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 21 of 34 Chapter 6 – Operation Power T o turn the touchmonitor on or off, pr ess the touchmonitor power button once. T o power on the Computer Module, pre ss the touchmonitor power button once.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 22 of 34 The APR performance can be customized to better suit your application. Access the “Set APR Preference” window from the Mode tab of the Elo APR driver control panel: Select the usage type best suited for y our application, then press Apply .
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 23 of 34 IntelliT ouch T ouch T echnology The IntelliT ouch touchscreen can be re-calibrated to your displayed video image, if needed, through the Calibration function in the Elo driver control panel.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 24 of 34 On-Screen Display (OSD) Four OSD buttons are provided on the rear of t he monitor to adjust various display parameters. The same buttons are provided on an optional OSD Control Box which can plug into the PS/2 connector on the touchmonitor connector panel.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 25 of 34 Maint ain Aspect Ratio Switches the scaling method between Full Scaling and Maintain Aspect Ratio. Default: Full Scaling Full Scaling – scales the X- and Y -dimensio ns of the input video (up or down as needed) to the display’s native resolution.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 26 of 34 V ideo Source The monitor continually scans for active video from VGA, HDMI, and the Computer Module. This adjustment selects which of those input ports should be given priority to be displayed.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 27 of 34 OSD and Power Lockout s Press and hold the “Menu” and “Up” buttons fo r two seconds to enable/disable the OSD Locking feature. When the OSD Locking is enabl ed, pressing any of the Menu, Up, Down, or Select keys will have no effect on the system.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 28 of 34 Chapter 7 – T echnical Support If you are experiencing trouble with your touc hmonitor , refer to the following suggestions. If the problem persists, please cont act your loca l dealer or cont act Elo T ouc hSystems Customer Service.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 29 of 34 Chapter 8 Safety & Maintenance Safety T o avoid ris k of electric shock, follow all safe ty notices and do not disa ssemble the touchmonitor or Computer Module. They are not user-serviceable.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 30 of 34 Mercury W arning The 3200L, 4200L, and 4600L products cont ain fluorescent lamps that cont ain mercury , which must be recycled or disposed of in accordan ce with local, state, o r federal laws.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 31 of 34 Chapter 9 - Regulatory Information I. Electrical Safety Information: Compliance is required with respect to the voltage, frequency , and current requirements indicated on the manufacturer ’s label.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 32 of 34 iii) Reorient the affect ed receiver’s antenna. iv)Plug the digital device into a dif ferent AC outlet so the digital device and the receiver are on different branch circuit s.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 33 of 34 Chapter 10 – W arranty Information Except as otherwise stated herein, or in an order acknowledgment delivered to Buyer , Seller warrants to Buyer that the Product shall be free of defect s in materials and workmanship.
User Manual – Interactive Digital Signage SW601 176 Rev D - Page 34 of 34 Check out Elo’ s W ebsite! www .elotouch.com Get the latest... • Product Information • Specifications • News on upco.
デバイスTyco Electronics 4200Lの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Tyco Electronics 4200Lをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはTyco Electronics 4200Lの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Tyco Electronics 4200Lの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Tyco Electronics 4200Lで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Tyco Electronics 4200Lを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はTyco Electronics 4200Lの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Tyco Electronics 4200Lに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちTyco Electronics 4200Lデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。