UNICOM ElectricメーカーGST-2402の使用説明書/サービス説明書
ページ先へ移動 of 34
908 Canada Court City of Industry , C A 91748 U.S.A. Phone: 626.964.7873 or 800.346.6668 F ax: 626.964.7880 www .unicomlink.com e-mail: info@unicomlink.com ©UNICOM 2004. UNICOM and “A Network Systems Solution” ar e trademarks of UNICOM Electric, Inc.
1. INTRODUCTION ...................................................................................................... 1 Features .................................................................................................................... 2 Software Features .
APPENDIX ................................................................................................................. 29 Console Port Pin Assignments ................................................................................ 29 Cables .....
1. Introduction Welcome to the World of Network Switching. In modern business, communication and information sharing are fundamental to success. Computer networks have proven to be one of the fastest ways of communication. The SmartGST-2402 is a multi-port Switch that can be used to build high- performance switched workgroup networks.
connections over long distances. Features IEEE802.3 10Base-T, IEEE802.3u 100Base-TX/FX, IEEE802.3ab 1000Base-T, IEEE802.3z Gigabit fiber Twenty-four 10/100TX ports plus one expansion slot with RS-232 for management Expansion modules available: 100FX, 1000T, 1000SX/LX IEEE802.
Software Features Management In-Band Local Console (RS-232) Port configuration Link speed, link mode, Port disable/Enable, Port Flow control disable/Enable, Port Auto negotiation Port Trunk IEEE802.3ad port trunk. Trunk groups up to 8. Maximum trunk port members up to 4.
Package Contents Unpack the contents of the SmartGST-2402 and verify them against the checklist below. SmartGST-2402 Fast Ethernet Switch Power Cord Four Rubber Feet RS-232 cable User Guide Rack mount kit SmartGST-2402 Four Rubber Feet RS-232 Cable Rack-mounted Kit Power Cord User Guide Figure 1-2.
This revolutionized networking. First, by allowing two-way, simultaneous transmissions over the same port (Full-duplex), which essentially doubled the bandwidth. Second, by reducing the collision domain to a single switch-port, which eliminated the need for carrier sensing.
2. Hardware Description This Section describes the hardware of the SmartGST-2402 and gives a physical and functional overview of this switch. The physical dimensions: 440mm x 161mm x 44mm (L x W x H) Front Panel The Front Panel of the SmartGST-2402 consists of twenty-four 10/100Base- TX RJ-45 ports (Auto MDI/MDIX) and one expansion slot.
LED Indicators The LED Indicators give real-time information of systematic operation status. The following table provides a description of LED status. Figure 2-2. LED indicators LED Status Description Green Power On Power Off Power is not connected Green The port is connecting with the device.
as shown in Figure 2-3. The Switch will work with AC in the range 100-240V AC, 50-60Hz. Figure 2-3. The Rear Panel of SmartGST-2402 Desktop Installation Set the Switch on a sufficiently large flat space with a power outlet nearby. The surface where you put your Switch should be clean, smooth, level and sturdy.
Rack-mounted Installation The SmartGST-2402 comes with a rack-mounting kit and can be mounted in any EIA standard size, 19" Rack. The Switch can be placed in a wiring closet with other equipment. Perform the following steps to rack mount the switch: A.
Figure 2-5. Mounting the Switch in an EIA standard 19" Rack Note: For proper ventilation, allow about at least 4" (10 cm) of clearance on the front and 3.4" (8 cm) on the back of the Switch. This is especially important for enclosed rack installations.
3. Network Application This section provides a few samples of network topology in which the Switch is used. The SmartGST-2402 is designed as a segment switch. With its large address table (8 k MAC address) and high performance, it is ideal for interconnecting networking segments.
Figure 3-1. Small Workgroup Application Segment Bridge This switch is an ideal solution for departmental users in corporate backbones where large data broadcasts are constantly broadcast. In the illustration below, two Ethernet switches with PCs, a print server, and a local server are all connected to the Switch.
Print Server Server Uplink to backbone switch 10/100Mbps port Giga port Figure 3-2. Department Bridge Application Connecting to the Switch The Console port is a female DB-9 connector that enables a connection to a PC or terminal for monitoring and configuring the Switch.
4. Console Management Login in the Console Interface When the connection between Switch and PC is ready, turn on the PC and run a terminal emulation program or Hyper Terminal and configure its communi.
Console main screen Main Menu There are 8 selections as follow. [1] Port Status: it displays status of the ports [2] Port Configuration: configure the port status. [3] Trunk Configuration: configure Trunk function. [4] Trunk Status: display Trunk Link fault information and Network Loop fault port detected information.
Main menu line interface Control Key description: The control keys provided in all menus: I/M/J/L: Move the vernier to up, down, left, and right. Enter: Edit finish or OK in function screen. Space: Toggle selected item to next configure or change the value.
Port Status It displays the status of the ports. Enter the “ 1 ” to enter the Port Status display interface. In the Port Status interface, using the “2” to view next page. Using the “ 1 ” to go back to previous page. Speed: display port connection speed.
Port configuration interface Enable: enabling or disabling this port. Speed advertisement: select speed and duplex mode of port. Flow Control: enabling or disabling the Flow Control function. Rx Bandwidth: set up the receive bandwidth.
trunk status to “ Enable ”. Trunk Configuration interface Trunk Status This window displays the trunk link warning information. When the trunking group has detected an error, the information will be displayed in this section.
QoS You can configure QoS functions. TOS/Diff Serv. Priority: enabling or disabling TOS/Diff service priority. 802.1p Priority: enabling or disabling 802.1p priority function. Priority Weight Ration (High: Low): select the priority weight ration mode – 1:0, 4:1, 8:1, or 16:1.
Priority Tag Insert/Remove Sets each port's tagging control. There are four choices of port tagging control: Disable: No port tagging control on this port.
name is "Switch-A". Broadcast Storm Filtering Control: enter “ 3 ” to change the value. Load Factory Default Setting: enter “ 1 ” to set the switch configuration value to default value. System interface VLAN Member Setup Configuring Port-Base VLAN group.
Add VLAN Group interface Delete VLAN Group 1. Press “ E ” to Edit mode. 2. Press “ D ” and enter the VLAN Entry No. 3. Press “ Enter ”. The system will ask you to confirm the deletion. Enter “ y ” to confirm the deletion. 4. Press “ Enter ” the VLAN group will be deleted.
Save Save all configurations changes. Without saving the configuration, the new setting will not take effect. If you turn off the device without saving the configurations, all changes will be permanen.
5. Troubleshooting This section is intended to help you solve the most common problems of the SmartGST-2402. Incorrect connections These ports can auto-detect straight or crossover cables when you link this switch with other Ethernet device. Always use the correct UTP or STP RJ-45 cable.
between end nodes. In addition, you should make sure that your network topology contains no data path loops. Between any two ends nodes, there should be only one active cabling path at any time. Data path loops will cause broadcast storms that will severely impact your network performance.
6. Technical Specification This section provides the specifications of SmartGST-2402, and the following table lists these specifications. Standard IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX/100BASE-FX IEEE802.3ab 1000BASE-T IEEE802.3z Gigabit fiber IEEE802.
Power 100~240VAC 50/60Hz Power Consumption 20Watts(Maximum) Dimensions 440mm x 161mm x 44mm (L x W x H) EMI & Safety FCC Class A, CE, UL, cUL, CE/EN60950.
Appendix Console Port Pin Assignments The DB-9 serial port on the front panel is used for out-of-band console configuration. The menu-driven console configuration program can be accessed from a terminal or a PC running a terminal emulation program.
Console Port to 9-Pin DTE Port on PC 9-Pin Serial Port CCITT Signal PC’s 9-Pin DTE Port 2 RXD <---------RXD ------------ 3 TxD 3 TXD -----------TXD ----------> 2 RxD 5 SGND -----------SGND.
data while pins 3 and 6 are used for receiving data. RJ-45 Pin Assignments Pin Number Assignment 1 Tx+ 2 Tx- 3 Rx+ 6 Rx- Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair. All ports on this switch support automatic MDI/MDI-X operation.
デバイスUNICOM Electric GST-2402の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
UNICOM Electric GST-2402をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはUNICOM Electric GST-2402の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。UNICOM Electric GST-2402の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。UNICOM Electric GST-2402で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
UNICOM Electric GST-2402を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はUNICOM Electric GST-2402の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、UNICOM Electric GST-2402に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちUNICOM Electric GST-2402デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
