UnidenメーカーLRD 2200SWSの使用説明書/サービス説明書
ページ先へ移動 of 26
Introduction Welcome to the world of sophisticated, early warning laser/ra dar detection. You have purchased one of the most advanced laser/radar detectors available.
Speed Detection Systems A speed detection device (often called a radar gun) sends out either a microwave signal or beam of light. When th is signal reaches its target, part of the signal is reflected or bounced back toward the emitting gun.
Laser The Laser Speed Detection System, also called LIDAR (for Light Detection and Ranging), uses a laser gun that emits infrared light pulses just outside the spectrum of visible light. E ach reflected pulse measures the speed of the object coming toward or going away from the laser gun.
Included with Your Radar Detector If any of these items are missing or damaged, contact your dealer immediately. Be sure to complete and mail the Product Registration Card.
Controls and Functions 1. Clip Release — Press the clip release button to remove the LRD 2200SWS from the windshield mounting clip. 2. Rear and Side Laser Detector Lenses — For rear and side detection of laser signals. 3. City Button — Press the CITY button t o help reduce X-band false alarms while driving in the city.
7. LED Display — LEDs display v isual alerts, signal strength, and operation mode. 8. On-Off/Volume Control — Turns the power on and adjusts the Audio Alert volume. 9. Speaker — Sounds audio alert. There are four different audio alert tones to distinguish each type of si gnal received.
1. X-Band Signal Indicator — A green LED lights and blinks to indicate the presence of an X-band radar signal. The b link rate increases as the radar source gets close r. A distinct audio alert is also heard. 2. K-Band Indicator — An amber (orange) LED ligh ts and blinks to indicate the presence of a K-band radar.
Installation The LRD 2200SWS uses a highly sensitive horn-type antenna and IR laser sensor to receive radar/laser signals. Its sensitiv ity and range depend on the method of installation and the direction of the antenna/sensor in relation to the signal source.
Adjusting the Wind shield Mounting Clip 1. The metal portion of the bracket locks into t he plastic portion at three different positions. These positions can be used for vehicles with different vertical angles of their windsh ields. The back position can be used for vehicles with windshields that are slanted back.
Connecting the Power Direct Connection The LRD 2200SWS is designed to op erate on most 12V DC negative ground vehicle electrical systems. The straight power cord provid ed with the unit has bare wires at one end, and a small connector at the other end.
3. Run the power cord from th e fuse box to the LRD 2200SWS. Your unit also comes with power cord mounting clips. You can use these clips to attach the power cord to the dashboard or other parts of the vehicle, keeping it neat and ou t of the way. Use the double-sided foam tape squares to attach each clip.
When installing the power cord, make sure that: • The socket is clean to allow proper contact. • The power cord does not block th e antenna area on the back of the unit.
Operation You are now ready to enjoy the convenience and security of your LRD 2200SWS. Please read this section of the Op erating Guide carefully to familiarize yourself with the basic operation of this unit. Power On Turn the Volume control to switch on the power.
Memory Re tention Featu re The Memory Retention Feature retains the LRD 2200SWS’s operational settings in memory for at least 2 days without power. When you turn on the LRD 2200SWS, it will be in the same mode as when y ou turned it off.
Visual Alert Only O peration You can operate the LRD 2200SWS in Visual Alert Only by setting the Volume control at the m inimum position i n Full Alert Mode. At t his setting you can barely hear the aud io alert in a quiet environment. Be sure that the Audio Alert Only indicator is off.
City Operation In highly populated areas, you may encounter many devices that use the same frequencies as radar signals, such as motion detectors, automatic doors, and intrusion alarms.
LED Signal Strength Meter in City Mod e The LED signal strength meter gives you instant information about the strength of the signal being detected. A weak signal ca uses the first LED to light, but as signal strength increases, more LEDs ligh t. All four LEDs light when full signal strength is received.
Care and Maintenance The LRD 2200SWS is designed to give you years of trouble-free service. There are no user-serviceable parts inside, and, except for the fuse, no maintenance is required. To keep your detector in new condition, follow these important suggestions: • Never leave the LRD 2200SWS on the windsh ield when you park your vehicle.
Troubleshooting If your LRD 2200SWS does not perform up to expectations, try the suggestions listed below. If you cannot get satisfactory results, call the Uniden Customer Service Center at (800) 297-1023, 8:00 a.m. to 5:00 p.m. Central Time, Monday through Friday.
Specifications General Dimensions: 3 1 ⁄ 9 in. (W ) x 4 5 ⁄ 8 in. (D) x 5 ⁄ 6 in. (H) Weight: 3.5 oz. Power Requir ements: 13.8 VDC Temperature Rang e: Operating: -5 °F to 160°F (-2 0°C to 70.
Optional Accessories & Replacement Parts Windshie ld Clip njdfjnjnjfnjfjn jnkjnjksnkjsnfj dfksfmkm kfmkmkmlf sfkkmmfmsmsm kkoioionksnkln mmkmkkl skdmkmkm sdmkmfmmmk mdmklkkkml mmkkllmmk njdfjnjnjf.
LRD 2200SWS Operating Guide USZZ01064BA ®.
Precautions Important: The LRD 2200SWS was not designed to help you disobey the law. Safe drivers always obey the posted speed limit and legal driving methods at all times. Federal and Local Regulations The FCC passed the Communications Act in 1934 to give all citizens the right to receive any type of radio transmission.
Features, Specifications, and availability of Optional Accessories are all subject to change without notice. Uniden ® is a registered trademark of Uniden America Corporation. Contents I n t r o d u c t i o n .......... ............ ............ .....
One Year Limited Warranty Important: Evidence of orig inal purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants, for on.
Covered under one or more of the following U.S. patents: 4,622,553 4,698,632 4,709,407 4,791,420 4,831,498 5,315,302 ©1996 Uniden America Corporation.
デバイスUniden LRD 2200SWSの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Uniden LRD 2200SWSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはUniden LRD 2200SWSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Uniden LRD 2200SWSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Uniden LRD 2200SWSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Uniden LRD 2200SWSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はUniden LRD 2200SWSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Uniden LRD 2200SWSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちUniden LRD 2200SWSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
