United States Stoveメーカー2007Bの使用説明書/サービス説明書
ページ先へ移動 of 16
1 owner's manual PEDEST AL PL A TE HEA TER moDel: 2007B .
2 Y ou've purchased a heater from North America's oldest manufacturer of wood burning products. By heating with wood you're helping to CONSERVE ENERGY! Wood is our only Renewable Energy Resource.
3 SAFETY NOTICE: If this heater is not properly installed a house re may result. For your safety, follow the installation directions. Contact local building or re ofcials about restrictions and installation inspection requirements in your area.
4 Keep the chimney connection as short as possible. The heater must have its own chimney ue. Do not connect any other appliance to the same ue. If there is no chim- ney where you wish to place the heater, you can use a UL Listed Type 103 HT, Solid Fuel, Factory Built Chimney.
5 This heater comes equipped with a cast-iron ue collar with holes to mount the solid damper as shown below. Flue Collar - 40292 Solid Damper - 40398 5/16-18 x 1-1/2" Bolts (3 req.
6 KEY DESCRIPTION PART NO. QTY. 1 Blower Motor 80442 1 2 Blower Housing Front 25090B 1 3 Blower Housing Back 25089B 1 4 Power Supply Cord 80232 1 5 Rheostat w/Nut and Knob 80090 1 6 Strain Relief Bush.
7 T wo basic types of chimneys are approved for use with solid fuel. Factory-built and masonry . Factory-built chimney must comply with UL standard in the US. Do not expect your stove or furnace to create draft.
8 Many people may wish to convert an existing replace to heater use. Usually, safe connection of stovepipe to a masonry chimney requires more effort than c onnection to a prefabricated chimney.
9 When considering a masonry chimney , round tiles are preferable to square or rectangular , as round tiles have much better airow character- istics and are far easier to clean. Unfortunately , most North American chimneys use square or rectangular tile liners that are really designed for open replaces, not stoves or furnaces.
10 Connection of the stovepipe directly into the existing masonry chimney over the replace opening is a more desirable method.
11 1. Crimped end of the pipe must be installed toward the heater . The pipe should slide inside the ue collar . The pipe should be rmly attached to the ue collar with 3 screws and sealed with furnace cement. 2. Slope any horizontal pipe upward toward the chimney at least 1/4 " inch for each foot of horizontal run.
12 Use Hardwood that has been split and air-dried to obtain maxi- mum burning efciency . 1.
13 Key Part No. Description Qty . 1 69427B Ash Pan 1 2 40487 Ash Dump Cover 1 3 24103 ½ Firebrick 2 4 89066 Full Firebrick 17 5 6.
14 .
15 1. Be sure heater has cooled before beginning. 2. Remove 12, 8-32 x ¼ screws and glass re- tainers with screw driver. 3. Remove damaged glass (2). 4. To reinstall glass, follow steps 1-2 in reverse order.
16 THIS MANUAL WILL HELP YOU OBT AIN EFFICIENT , DEPENDABLE SER VICE FROM YOUR 2007B HEA TER, AND ENABLE YOU TO ORDER REP AIR P ARTS CORRECTL Y . KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE. WHEN WRITING, AL W A YS GIVE THE FULL MODEL NUMBER WHICH IS ON THE NAMEPLA TE A TT ACHED T O THE HEA TER.
デバイスUnited States Stove 2007Bの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
United States Stove 2007Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはUnited States Stove 2007Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。United States Stove 2007Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。United States Stove 2007Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
United States Stove 2007Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はUnited States Stove 2007Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、United States Stove 2007Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちUnited States Stove 2007Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
