Vaxメーカー17RTCの使用説明書/サービス説明書
ページ先へ移動 of 32
17/19-INCH PREMIUM TFT-LCD MONITOR INSTRUCTION MANUAL 17RTC / 19RTC INSTRUCTION MANUAL Please read this manual thoro ughly before us e, and ke ep it handy for future reference.
SAFETY INSTRUCTION……………………………… …………………………………….2 - 3 CAUTIONS ……………………………… ………..…… ……………… ………… ……………..4 FCC RF INTERFERENCE STATEMENT …… …… ……………………………… ………….
1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instruction s marked on the product. 4. Unplug this product from the wall outlet before cle an ing. Do not use liquid cleaners or ae rosol cleaners.
Refer all servicing to service personnel. 14. Unplug this product from the wall ou tlet and refer servicing to qualified service personnel under the following conditions. A. When the power cord or plug is damaged or frayed. B. If liquid has been spilled into the product.
▶ NEVER REMOVE THE BACK COV ER Removal of the back cover should be carri ed out only by qualified personnel. ▶ DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard, do not expose the unit to rain or moisture. This unit is designed to be used in the office or home.
NOTE This equipment has been tested a nd fou nd to comply with the limits for a Class B digital device , pursuant to Part 15 of the FCC Rules. T hese limits are designe d to provide rea sonable protection against harmful interference i n a residential installation.
A. BOTTOM PANEL CONTROL 1. DC 12V IN 2. COMPONENT Y,Pb,Pr & SOUND L,R IN 3. AUDIO OUT 4. PC STEREO IN 5. D-SUB IN 6. DVI IN 7. HDMI IN (OPTION) B. SIDE PANEL CONTROL 1. VIDEO 1(AV1) IN 2. VIDEO 1(AV1) OUT 3. VIDEO 2(AV2) IN 4. VIDEO 2(AV2) OUT 5. S-VIDEO (Y/C) IN 6.
C. REMOTE CONTROLLER 1. POWER( ) Turns the power ON or O FF. There will be a few seconds delay before the d isplay appears. 2. SOURCE Select pc or video( AV1 / AV2 / S-Video / PC ) sources. 9. AUTO Auto geometry adjustment in PC Source. 10. MUTE Mute the sound.
D. FRONT KEY CONTROL 1. POWER ON/OFF( ) Turns the power ON or O FF. There will be a few seconds delay before the d isplay ap pears. 2. MENU / EXIT Activates and exits the On Screen Display. 3. SOURCE/SELECT Select PC or video source. Select On Screen Display menu 4 / 5.
OSD MENU DESCRIPTION A: CUSTOM MENU (Only Video mode) Press the MENU button and then up( ▲ ) / down( ▼ ) button to select the Cu stom menu. Press the up( ▲ ) / down( ▼ ) button to sel ect Custom sub menu. Press the left(◀) / right( ▶ ) button to adjust picture setting.
A: CUSTOM MENU (Only PC mode) Press the MENU button and then up( ▲ ) / down( ▼ ) button to select the Cu stom menu. Press the up( ▲ ) / down( ▼ ) button to sel ect Custom sub menu. Press (◀) / right( ▶ ) button to adjust picture setting. Press the MENU button to save.
B. Picture / Sound Menu(Only Video mode) Press the MENU button and then up( ▲ ) / down( ▼ ) button to select the Picture / Sound. Press the right( ▶ ) or ENTER button. 1. Picture Mode Press the up( ▲ ) / down( ▼ ) button to sel ect the Picture Mode.
2. Color Tone Press the up( ▲ ) / down( ▼ ) button to sel ect the Color Tone. Press the ( ▶) or ENTER button and then up( ▲ )/down( ▼ ) button to sele ct the desired color tone.
3. Mute Press the up( ▲ ) / down( ▼ ) button to select the Mute. Press the ( ▶) or ENTER button and then up( ▲ )/down( ▼ ) button t o select the desired Mute.
4. Volume Press the up( ▲ ) / down( ▼ ) button to select the Volume. Press (◀) / right( ▶ ) button to adjust Volume. Press the MENU button to save.
Press the ( ▶) or ENTER button and then up( ▲ )/down( ▼ ) button t o select the desired Size. Press the MENU button to save. 6. PC (Only PC mode) Press the up( ▲ ) / down( ▼ ) button to sel .
Press the up( ▲ ) / down( ▼ ) button to sel ect PC sub m enu Press the right( ▶ ) or ENTER button and then left (◀ ) / right( ▶ ) button to adjust PC setting. Press the MENU button to save. Auto Adjust: Auto geometry adjustment Phase: Adjust the number of horizontal picture elem ents.
1. PIP Press the up( ▲ ) / down( ▼ ) button to sel ect the PIP. Press the right( ▶ ) or ENTER button and then pre ss up( ▲ ) / down( ▼ ) button to select the On or Off. Press the MENU button to save. 2. Input Source Press the up( ▲ ) / down( ▼ ) button to sel ect the Input Source.
Press the right( ▶ ) or ENTER button and then pre ss up( ▲ ) / down( ▼ ) button to select the desire Input Source. Press the MENU button to save.
Press the right( ▶ ) or ENTER button and then pre ss up( ▲ ) / down( ▼ ) button to select the desire Size. Press the MENU button to save. 4. Position Press the up( ▲ ) / down( ▼ ) button to sel ect the Positi on.
Press the right( ▶ ) or ENTER button and then pre ss up( ▲ ) / down( ▼ ) button to select the desire Position. Press the MENU button to save. 5. Swap Press the up( ▲ ) / down( ▼ ) button to sel ect the Swap.
5. Sound Select Press the up( ▲ ) / down( ▼ ) button to sel ect the Soun d Select. Press the right( ▶ ) or ENTER button and then pre ss up( ▲ ) / down( ▼ ) button to select the desire Sound Select.
D. SETUP MENU Press the MENU button and then up( ▲ ) / down( ▼ ) button to select the Setup me nu. Press the right( ▶ ) or ENTER button . 1.Reset Press ENTER button to select the reset Reset : Select to reset all setting to the factory default values.
2. Language Press the up( ▲ ) / down( ▼ ) button to sel ect the Language menu. Press the right( ▶ ) or ENTER button. Press the up( ▲ ) / down( ▼ ) button to sel ect language.
3. OSD Tone Press the up( ▲ ) / down( ▼ ) button to sel ect the OSD t one menu. Press the right( ▶ ) or ENTER button Press the up( ▲ ) / down( ▼ ) button to sel ect the desire OSD Tone.
4. Blue Screen Press the up( ▲ ) / down( ▼ ) button to sel ect the blue screen. Press the right( ▶ ) or ENTER button. Press the up( ▲ ) / down( ▼ ) button to select on or off.
5. Key Lock Press the up( ▲ ) / down( ▼ ) button to sel ect the key lock menu. Press the right( ▶ ) or ENTER button Press the up( ▲ ) / down( ▼ ) button to select on or off Press the MENU button to save.
Wall mount installation : 1) Remove the monitor stand bracket assembled with the monitor. 2) Us e the VESA standard mount ing design and the 100mm hole pattern on the back pan el to install the L CD monit or to the (Optional) mounting bracket sold separately .
▶ PIN ASSIGNMENTS ▶ ACCESSORY 1. POWER CORD 2. USER’S MANUAL 3. PC cable 4. Adaptor 5. Remote Control 6. Batteries 7. Wall mount (Option) 8. Rack mount (Option) INSTRUCTION MANUAL ………….
This monitor features a power m anagement sy stem to “power d o wn” upon receipt of the VESA DPMS(The display power management si gnaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs th is signaling system through not sending horizontal, vertical, or sync signal.
17“ 19“ 17 ˝ Diagonal AM-TFT(A ctive-Matrix) 19 ˝ Diagonal A M-TFT(Active-Matrix) Pixel pitch(mm) : 0.264(H) 0.264(V) Pixel pitch(mm) : 0.294(H) 0.
WEEE Symbols 31 ………………………………… ………………………………………… INSTRUCTION MANUAL “ Going to Sleep” message on screen Correct Disposal of This Product (Wa.
デバイスVax 17RTCの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Vax 17RTCをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVax 17RTCの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Vax 17RTCの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Vax 17RTCで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Vax 17RTCを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVax 17RTCの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Vax 17RTCに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVax 17RTCデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。