VinotempメーカーVINO6500HZDの使用説明書/サービス説明書
ページ先へ移動 of 25
WINE-MATE Cooling Unit Use & Care Manual VINO1500HZD VINO2500HZD VINO3500HZD VINO4500HZD VINO6500HZD VINO8500HZD V V i i n n o o t t e e m m p p I I n n t t e e r r n n a a t t i i o o n n a a l l C C o o r r p p . . w w w w w w . . w w i i n n e e m m a a t t e e .
- 1 - Important Safety Information • DO NOT PLUG IN UNTIL 24 HOURS AFTER DELIVERY. • DO NOT USE A GROUND FAUL T INTERRUPTER (GFI). • A DEDICATED 15 OR 20 AMPCIRCUI T IS HIGHLY RECOMMENDED.
- 2 - TABLE OF CONTENTS Feature Description…………………………….……………..3 Installation Instruction………………………………………..5 Temperature Control & Humidity Adjustment...………..12 Care Guide…………………………………………………… .
- 3 - Feature Description • HZD cooling unit is designed and us ed to provide a stable temperature between 50~65 ° F for suitable space at a normal environment. • The refrigerated space will mainta in humidity of 50~70% RH even when the environment becomes dry and humid.
- 4 - • See the voltage, frequency and current from the label on the back or side of the cooling unit. The dimension and capacity are specified as follows: MODEL COOLING CAPACITY, CFM 55 ° F/75 ° F BOTTLE CAPACITY 55 ° F/75 ° F DIMENSIONS IN. WXHXD ELECTRICAL WEIGHT (lb) VINO- 1500HZD 1500 Btu/h, 120 CFM 150 cu ft 800 bottles 14.
- 5 - Installation Instruction Select a place to mount the unit where t he exhaust airflow is unobstructed for a minimum of 6 inch. The area into which t he unit exhausts must be well ventilated. If it is not, heat exhaust ed by the unit will build up and the unit will not operate properly.
- 6 - Fig. 2.1 CABINET CUTOUT & GASKET LIP Fig. 2.2 GASKET.
- 7 - Fig. 2.3 TOP EXHAUST GASKET Fig. 2.4 THREAD INSERT.
- 8 - Fig. 2.5 COOLING UNIT Fig. 2.6 FASTENING BRACKET & SCREW.
- 9 - Fig. 2.7 CABINET GRILLE 2. VINO3500-8500HZD THROUGH WALL INSTALLATION 1. Cut a rectangular opening at the wine room wall as illustrated. The dimensions of the opening shall be 1/4” larger than the width and height of the unit.
- 10 - Fig. 2.8 THROUGH WALL INSTALLATION Fig. 2.9 TOP EXHAUST GASKET.
- 11 - 3. Cellar Construction This is only a guide and shall be c onsidered as minimum requirements. All interior walls and floors shall have a vapor barrier and a minimum of R11 insulation. All exterior walls and ceiling shall have a vapor barrier and a minimum of R19 insulation.
- 12 - Temperature Control & Humidity Adjustment 1. Temperature Setting • Set the temperature at 55 ° F for the optimum aging of wine • On initial start-up, the time required to reach the desired temperature will vary, depending on the quantit y of bottles, temperature setting and surrounding temperature.
- 13 - 2) Alarm Signals 2.1 Code Description 2.2 Alarm Recovery Probe alarms P1”, start a few seconds afte r the fault in the re lated probe; they automatically stop a few seconds afte r the probe restarts normal operation. Check connections before replacing the probe.
- 14 - 2. The value of the set point will be di splayed and the “°C” or “°F” LED starts blinking; 3. To change the Set value, push the keys or arrows within 10s. 4. To memorize the new set point value, push the SET key again or wait 10s. 4) Humidity Adjustment The parameter Fon is used to adjust the humidity in the wine cabinet.
- 15 - 7) Manual Defrost Push the DEF key for more than 2 se conds and a manual defrost will start..
- 16 - Care Guide 1. Coil Cleaning • Clean the condenser coil regularly. Coil may need to be cleaned at least every 6 months. • Coil is on the ambient air intake side of the cooling unit.
- 17 - Troubleshooting This Troubleshooting Chart is not prepared to replace the training required for a professional refrigeration servic e person, not is it comprehensive Troubleshooting Chart Complaint Possible Causes Response 1.Unit not running a.
- 18 - 6. “HA” alarm blinking and beeping, temperature high or not cooling and running continually a. Improper room insulation & seal b. Room too large c. Ambient temperature too high d. Exhaust restricted e. Malfunctioning fans f. Improper evaporator or condenser airflow g.
- 19 - f. Refrigerant low or leaki ng g. Capillary tube blockage f. Check for current and sealed system leakage g. Check fo r low side pressure 11.Water leak a. High humidity b. Air leak in wine cellar c. Evaporator air flow restriction d. Water passages restricted e.
- 20 - Wiring Diagram Fig. 6.1 VINO1500-2500H ZD Wiring Diagram Fig. 6.2 VINO1500-2500HZD CALLI NG FEATURE WIRING DIAGRAM.
- 21 - Fig. 6.3 VINO3500-8500H ZD Wiring Diagram Fig. 6.4 VINO3500-8500HZD Ca ll Feature Wiring Diagram.
- 22 - Customer Support If you still have problems, please contact us at: Vinotemp International 17631 South Susana Road Rancho Dominguez, CA 90221 Tel: (310) 886-3332 Fax: (310) 886-3310 Email: info@vinotemp.
- 23 - Warranty Thank you for choosing a Vinotemp cooling unit. Please enter the complete model and se rial numbers in the space provided: Model_____________ _________________________ __ _________________ Serial No._________________ ____________________ _________________ Attach your purchase receipt to this owner’s manual.
- 24 - is determined to be faulty and is within the twelve month warranty period VINOTEMP will, at its discret ion, repair or replace the unit and return it free of charge to the original retail customer. If the unit is found to be in good working order, or beyond the initial twelve month period, it will be returned freight collect.
デバイスVinotemp VINO6500HZDの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Vinotemp VINO6500HZDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVinotemp VINO6500HZDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Vinotemp VINO6500HZDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Vinotemp VINO6500HZDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Vinotemp VINO6500HZDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVinotemp VINO6500HZDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Vinotemp VINO6500HZDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVinotemp VINO6500HZDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
