VinotempメーカーWINE-MATE VINO1500HZDの使用説明書/サービス説明書
ページ先へ移動 of 24
WINE-MATE Cooling Unit Use & Care Manual VINO1500HZD VINO2500HZD VINO3500HZD VINO4500HZD VINO6500HZD VINO8500HZD V V i i n n o o t t e e m m p p I I n n t t e e r r n n a a t t i i o o n n a a l l C C o o r r p p . . w w w w w w . . v v i i n n o o t t e e m m p p .
- 1 - Important Safety Information • DO NOT PLUG IN UNTIL 24 HOURS AFTER DELIVERY. • DO NOT USE A GROUND FAUL T INTERRUPTER (GFI). • A DEDICATED 20 OR 30 AMPCIRCUIT IS REQUIRED (1500-4500HZD OR 6500-8500HZD).
- 2 - TABLE OF CONTENTS Features & Specifications.…………………….……………..3 Installation Instruction………………………………………..5 Temperature Control & Humidity Adjustment...………..13 Care Guide…………………………………………………… .
- 3 - Features and Specifications • HZD cooling unit is designed and us ed to provide a stable temperature between 50~65 ° F for suitable space at a normal environment. • The refrigerated space will mainta in humidity of 50~70% RH even when the environment becomes dry and humid.
- 4 - Fig. 1.2 DIMENSIONS The dimension and capacity are specified as follows: MODEL CFM CAPACITY cu ft (55 ° F/75 ° F) DIMENSIONS W”XD”XH” ELECTRICAL WEIGHT (lb) VINO-1500HZD 120 90 14.25X16X13.25 115V/60HZ/4A 50 VINO-2500HZD 180 200 14.25X16X13.
- 5 - Installation Instruction Select a place to mount the unit where t he exhaust airflow is unobstructed for a minimum of 6 inch. The area into which t he unit exhausts must be well ventilated. If it is not, heat exhaust ed by the unit will build up and the unit will not operate properly.
- 6 - • If top exhaust, place another gaskets al ong the top exhaust at the top of the cooling unit (see Fig.2.3). • Move the cooling unit towards the m ounting sides and push to press the gaskets (see Fig 2.5). • Fasten the 2 brackets and use 7/16” wrench to tighten t he two ¼” screws (see Fig 2.
- 7 - Fig. 2.2 GASKET Fig. 2.3 TOP EXHAUST GASKET.
- 8 - Fig. 2.4 THREAD INSERT Fig. 2.5 COOLING UNIT.
- 9 - Fig. 2.6 FASTENING BRACKET & SCREW.
- 10 - Fig. 2.7 CABINET GRILLE 2. VINO3500-8500HZD THROUGH WALL INSTALLATION • Cut a rectangular opening at the win e room wall as illustrated. The dimensions of the opening shall be 1/4” larger than the width and height of the unit.
- 11 - • Attach the molding to the wall not the unit. • Plug the unit into a properly gr ounded and dedicated outlet of adequate capacity. Fig. 2.8 THROUGH WALL INSTALLATION Fig.
- 12 - 3. Cellar Construction This is only a guide and shall be c onsidered as minimum requirements. All interior walls and floors shall have a vapor barrier and a minimum of R11 insulation. All exterior walls and ceiling shall have a vapor barrier and a minimum of R19 insulation.
- 13 - Temperature Control & Humidity Adjustment 1. Temperature Setting • Set the temperature at 55 ° F for the optimum aging of wine • On initial start-up, the time required to reach the desired temperature will vary, depending on the quantit y of bottles, temperature setting and surrounding temperature.
- 14 - 2.1 LED Functions LED MODE FUNCTION ON Compressor enabled Flashing Anti-short cycle enabled ON Defrost cycle enabled ON Fan enabled Flashing Fan delay after defrost enabled ON Alarm occurring ON Temperature measuring unit Flashing Programming mode 3) Alarm Signals 3.
- 15 - 5) Parameter Programming 1. Press the SET + keys for 3 sec until the “ °C” or “°F” LED starts blinking, then release the keys. 2. Press again the SET + keys for more th an 7sec until the Pr2 label will be displayed, then release the keys.
- 16 - Care Guide 1. Coil Cleaning • Clean the condenser coil regularly. Coil may need to be cleaned at least every 6 months. • Coil is on the ambient air intake side of the cooling unit.
- 17 - Troubleshooting This Troubleshooting Chart is not prepared to replace the training required for a professional refrigeration servic e person, not is it comprehensive Complaint Possible Causes Response 1. Unit not running a. Power cord unplugged b.
- 18 - l. Failed components l. Check comp ressor windings, sta rt relay and overload protector 5. Unit running too long a. Improper room insulation & seal b. Exhaust restricted c. Room too large d. Ambient temperature higher > 90 ° F e. Dir ty C ondenser a.
- 19 - 11. Evaporator freezing up a. Evaporator air flow restricti on b. Not stopping due to air leak, high ambient temperature or low setting c. Low ambient temperature d. Bad thermostat or sensor e. Moisture in the system f. Refrigerant low or le aking g.
- 20 - Wiring Diagram Fig. 6.1 VINO1500-2500H ZD Wiring Diagram Fig. 6.3 VINO3500-8500H ZD Wiring Diagram.
- 21 - Customer Support If you still have problems, please contact us at: Vinotemp International 17631 South Susana Road Rancho Dominguez, CA 90221 Tel: (310) 886-3332 Fax: (310) 886-3310 Email: info@vinotemp.
- 22 - Warranty Thank you for choosing a Vinotemp cooling unit. Please enter the complete model and se rial numbers in the space provided: Model____________________ ____________________ _________________ Serial No._________________ ____________________ _________________ Attach your purchase receipt to this owner’s manual.
- 23 - is determined to be faulty and is within the twelve month warranty period VINOTEMP will, at its discret ion, repair or replace the unit and return it free of charge to the original retail customer. If the unit is found to be in good working order, or beyond the initial twelve month period, it will be returned freight collect.
デバイスVinotemp WINE-MATE VINO1500HZDの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Vinotemp WINE-MATE VINO1500HZDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVinotemp WINE-MATE VINO1500HZDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Vinotemp WINE-MATE VINO1500HZDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Vinotemp WINE-MATE VINO1500HZDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Vinotemp WINE-MATE VINO1500HZDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVinotemp WINE-MATE VINO1500HZDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Vinotemp WINE-MATE VINO1500HZDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVinotemp WINE-MATE VINO1500HZDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
