Vision FitnessメーカーST200の使用説明書/サービス説明書
ページ先へ移動 of 20
Assembly Guide ST200 FUNCTIONAL TRAINER.
2 T o avoid possible damage to this Functional T rainer , please follow these assembly steps in the correct order . Before proceeding, find your new Functional T rainer serial number located on the ba.
3 2 STEP 1 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7 STEP 8 STEP 9 STEP.
4 19mm Wrench 6mm L-Shaped Wrench TOOLS & P AR TS INCLUDED P AR TS BOX Color-coded Hardware Bags Owner’ s Guide Assembly Guide W arranty Card 10mm/17mm Wrench 4mm L-Shaped Wrench.
5 ORANGE BAG BLUE BAG HARDW ARE INCLUDED SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 4 10.5 x 18 x 2T Flat W asher Quantity: 8 M10 x 1.5P Nut Quantity: 6 M10 x 1.5P x 60L Bolt Quantity: 4 M10 x 1.5P x 25L Bolt Quantity: 2 M6 x 1P x 15L Bolt Quantity: 2 M10 x 1.
6 PINK BAG GREEN BAG HARDW ARE INCLUDED 10.5 x 18 x 2T Flat W asher Quantity: 2 M10 x 1.5P Nut Quantity: 2 M10 x 1.5P x 60L Bolt Quantity: 2 M10 x 1.5P x 25L Bolt Quantity: 8 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 6 10.5 x 18 x 2T Flat W asher Quantity: 4 M10 x 1.
7 BLACK BAG YELLOW BAG HARDW ARE INCLUDED 10.5 x 18 x 2T Flat W asher Quantity: 6 M10 x 1.5P Nut Quantity: 4 M10 x 1.5P x 60L Bolt Quantity: 2 M6 x 1P x 50L Bolt Quantity: 2 M12 Slotted Bolt Quantity: 3 6.4 x 14 x 1T Flat W asher Quantity: 2 M6 x 1P Nut Quantity: 2 Karabiner Quantity: 5 SW10.
8 RED BAG HARDW ARE INCLUDED SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 10 M10 x 1.5P x 25L Bolt Quantity: 10.
9 1d 1b 1e 1c 1a 1 STEP • Lay the back side of the rear vertical upright (1a) down onto the floor . The threaded bolt ends will be pointing up. Place the center floor support (1b) over the threaded ends. Attach a flat (10.5x18x2T) and spring (SW10.2x18.
10 2 STEP • Thread pull pins par tially onto 2a (Qty . 1) and 2c (Qty . 2). • Lay the front center vertical (2f) on the floor . Slide the seat suppor t structure (2a) over the open end of 2f. NOTE: Y ou must pull the pull pin out (2b) and hold it when sliding over 2f.
11 3 STEP • Place the top front structure (3a) on top of 2f and attach with two bolts (M10x1.5Px60L), two flat (10.5x18x2T) washers, and two nuts (M10x1.5P). Tighten fasteners with a 6mm L-shaped wrench and a 17mm wrench. • Attach the seat (3b) up through the bottom of 2a with four bolts (M10x1.
12 4 STEP • Place the bottom of the left oval upright (4a) onto the protruding bolts of 1d. NOTE: Make sure the 27 holes of 4a are on the outside. Mate the hole in the top of 4a with the top hole of 3a. Attach and tighten one flat (10x30x2T) & spring (SW10.
13 5 STEP • If you are adding 15 weight plates to the base unit, proceed as follows. If you are adding 20 weight plates, the steel tube spacer (5a) will not be used. • Place two rubber weight plate bumpers (5b) over the 0.75” holes of 5a. Place 5a over the holes of 1b.
14 6 STEP Wrap one end of cable #1 around pulley A. On the right side of the unit, place it through pulleys B, C, D of 6a, and E. Remove the nuts from 2 slotted bolts (M12) (see diagram below). With the threads pointing down on the slotted bolt (M12), slide the end of cable #1 through it.
15 7 STEP If assembling just the base unit ( ST200 ), proceed as follows. If assembling with the leg press ( ST250 ), refer to Step 5 of the leg press assembly guide. Slide the small steel end of cable #2 through pulleys F and G. Remove the nuts from the slotted bolt (M12).
16 8 STEP • Remove the slotted bolts (8a) located on the inside of the right and left handles of uprights 4a & 4b. Remove the nuts from the bolts. Slide the small steel end of cable #3 through pulleys H & I. Continue through pulleys J thru P .
17 9 STEP • Place the rear hole of the left decorative cover (9a) over the threaded post on the left side of structure 5e. Loosely attach a spring (SW10.2x18.4x2.5T) washer and a bolt (M10x1.5Px25L). Thread two bolts (M10x1.5Px25L) and two spring (SW10.
18 General Warning/Safet y Decal Placement Weight Plate Sticker Placement 10 STEP • Attach the decals according to the diagram below . DECALS.
19.
500 South CP Avenue • P .O. Box 280 • Lake Mills. WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 www .visionfitness.com © 2005 Vision Fitness.
デバイスVision Fitness ST200の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Vision Fitness ST200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVision Fitness ST200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Vision Fitness ST200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Vision Fitness ST200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Vision Fitness ST200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVision Fitness ST200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Vision Fitness ST200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVision Fitness ST200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。