VivitekメーカーD555の使用説明書/サービス説明書
ページ先へ移動 of 65
Copyright This publication, including all photographs, illust ra tions and software, is protected under international copyright laws, with all righ ts reserved. Neither this manu al, nor any of the material contained herein, may be reproduced without written consent of the author.
DLP Projector—User’s Manual — ii — Important Safety Information Important: It is strongly recommended that you read this sect ion carefully b efore using the projector. These safety and usage instructions will ensure that you enj oy many years of safe use of the pr ojector.
Preface Projector Installation Notice Place the projector in a horizontal p osition The tilt angle of the projector should not exceed 15 degrees, nor sho uld the projector be installed in any way other than the desktop and ce iling mount, otherwi se lamp life could decrease dramatically, and may lead to other unpredictable damages .
DLP Projector—User’s Manual — iv — Verify Installation Location To supply power, the 3-blade (with earth ing lead) socket should be used to en sure proper grounding and equalize d ground potential for all of the equipment in the Proje ctor System.
Preface – v – Choosing a Projector Edge blending application Not only brightness, bright balances, lens but st ability is important too when ch oosing a projector.
DLP Projector—User’s Manual Power Safety Only use the supplied power cord. Do not place anything on the powe r cord. Place the power cord wher e it will not be in the way of foot traffic. Remove the batteries from the remote control whe n storing or not in use for a prolonged period.
Preface – vii – Main Features Lightweight unit, easy to pack away and transport. Compatible with all m ajor video stand ards including NTSC, P AL, and SECAM. A high brightness ratin g allows for presentation s in daylight or in lit rooms.
DLP Projector—User’s Manual — viii — Table of Contents GETTING STARTED .......................................................................................................................................................... 1 P ACKING C HECKLIST .
Preface – ix – S PECIFICATIONS ................................................................................................................................................................. 44 P ROJECTION D ISTANCE VS . P ROJECTION S IZE ......
DLP Projector—User’s Manual – 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and che ck that the following items are included: DLP P ROJECTOR M en u P o w e r V o l um .
DLP Projector—User’s Manual Views of Projector Parts Front-right View 1 2 3 4 5 I TEM L ABEL D ESCRIPTIO N S EE PAGE 1. IR receiver Receive IR signal from rem ote control 2. Lens Projection Lens 3. Focus ring Focuses the projected image 4. Zoom ring Enlarges the projected image 14 5.
DLP Projector—User’s Manual Top view—On-screen Display (OSD) buttons and LEDs 1 2 3 4 5 6 7 8 I TEM L ABEL D ESCRIPTIO N S EE PAGE 1. Keystone Navigates and changes settings in the OSD Quick Me nu – For Keystone 2. MENU Opens and e xits OSD menus 3.
DLP Projector—User’s Manual Rear view Warning: As a safety precaution, disconnect all power to the projector and connecti ng devices before making connections. 1 2 3 45 6 7 8 9 1 0 11 12 I TEM L ABEL D ESCRIPTIO N S EE PAGE 1. AC IN Connect the POWER cable 9 2.
DLP Projector—User’s Manual Bottom view 1 2 1 12 2 I TEM L ABEL D ESCRIPTIO N S EE PAGE 1. Ceiling support ho les Contact your dealer for in formation on mounting the projecto r on a ceiling 2. Tilt adjustor Rotate adju ster lever to adjust angle position .
DLP Projector—User’s Manual Remote Control Par ts 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Menu Power Vo l u m e Freeze Auto Source Mute I TEM L ABEL D ESCRIPTIO N S EE PAGE 1. Up cursor Navigates and changes settings in the OSD 2. Enter Changes settings in the OSD 15 3.
DLP Projector—User’s Manual Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow (A) . Pull out the cover (B) . 2. Insert the battery with the positive side facing up. 3.
DLP Projector—User’s Manual — 8 — Important: 1. Avoid using the projector with bright fluore scent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the pr ojector.
DLP Projector—User’s Manual – 9 – S ETUP AND O PERATION Starting and Shutting down t he Projec tor 1. Connect the power cord to the projector. Connect the other end to a wall outlet. The POWER LED on the projector light. 2. Turn on the connected devices.
DLP Projector—User’s Manual 5. When the “Power Off? /Press Power again” messa ge appears, press the POWE R button. The proj ector turns off. Caution: Do not unplug the power cord until the POWER LE D stops flashing–indicati ng the projector has cooled down.
DLP Projector—User’s Manual Setting an Access Password (Secu rity Lock) You can use the four (arrow) buttons to set a password and pr event un authorized use of the projector. When enabled, the password must be entered after you p ower on the projector.
DLP Projector—User’s Manual 5. You can use the cursor buttons ▲▼◄► either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but not less than five. Press the cursor buttons in any order to set the password.
DLP Projector—User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector: The projector table or st and should be level and sturdy . Position the projector so that it is perpendicular t o the screen.
DLP Projector—User’s Manual Adjusting the Zoom, Focus and Keystone 1. Use the Image-zoom control (on the projector only) to resize the projected image and screen size . 2. Use the Image-focus control (on the projector only) to sharpen the projected image .
DLP Projector—User’s Manual – 15 – O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD You can use the remote contro l cursor buttons to navigate and make changes to the OSD.
DLP Projector—User’s Manual Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to Settings 1 . Press the cursor ▲▼ button to move to the Advanced 1 menu.
DLP Projector—User’s Manual OSD Menu Overview Use the following illustration to quickly find a se tting or determine the range for a setting. Image Settings 1 Off, On Blank, Red, Gre en, Blue, Whi.
DLP Projector—User’s Manual Image Menu Attention ! All of display mode parameters when changed will be saved to user mode. Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image Menu . Press the cursor ▲▼ button to move up and down in the Image menu.
DLP Projector—User’s Manual Computer Menu Press the MENU button to open the OSD menu. Press ◄► to move to the Image menu. Press ▲▼ to move to the Computer menu and then press Enter or ► . Press ▲▼ to move up and down in the Computer menu.
DLP Projector—User’s Manual Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Advanced menu and then press Enter or ► . Press ▼▲ to move up and down in the Advanced menu.
DLP Projector—User’s Manual Color Manager Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Color Manager menu and then press Enter or ► . Press ▼▲ to move up and down in the Color Manager menu.
DLP Projector—User’s Manual Settings 1 Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Settings 1 menu. Press the cursor ▲▼ button to move up and down in the Settings 1 menu. Press ◄► to enter and change values for settings.
DLP Projector—User’s Manual Audio Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press ▼ ▲ to move to the Audio menu and then press Enter or ► . Press ▼▲ to move up and down in the Audio menu. I TEM D ESCRIPTIO N Volume Press the ◄► buttons to enter and adjust th e audio volume.
DLP Projector—User’s Manual Advanced 1 Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press ▲ ▼ to move to the Advanced 1 menu and then press Enter or ► . Press ▲▼ to move up and down in the Advanced 1 menu.
DLP Projector—User’s Manual 3D Setting I TEM D ESCRIPTIO N 3D Press the cursor ◄► butt on to enter a nd select diffe rent 3D m ode. 3D Sync In vert Press the curso r ◄► button t o enter and e nable or di sable 3D Sy nc Invert. 3D Format Press the c ursor ◄► button to e nter and e nable or di sable differe nt 3D For mat.
DLP Projector—User’s Manual Advanced 2 Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press ▲ ▼ to move to the Advanced 2 menu and then press Enter or ► . Press ▲▼ to move up and down in the Advanced 2 menu.
DLP Projector—User’s Manual Settings 2 Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Settings 2 menu.
DLP Projector—User’s Manual Status Press the cursor ▲▼ button to move up and down in the Settings 2 menu. Select the Status menu and press Enter or ► to enter. I TEM D ESCRIPTIO N Active Source Display the activated source. Video Info rmation Displays resol ution/ video inf ormation f or RGB source a nd colo r standar d for Vide o source.
DLP Projector—User’s Manual Advanced 1 Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. Press ▲ ▼ to move to the Advanced 1 menu and then press Enter or ► . Press ▲▼ to move up and down in the Advanced 1 menu.
DLP Projector—User’s Manual Lamp Hour Reset Please refer to Resetting the Lamp on page 36 to reset the lamp hour counter. — 30 —.
DLP Projector—User’s Manual Advanced 2 Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. Press ▲ ▼ to move to the Advanced 2 menu and then press Enter or ► . Press ▲▼ to move up and down in the Advanced 2 menu.
DLP Projector—User’s Manual Source Filter Press the ENTER button to enter the Source Filter sub m enu. I TEM D ESCRIPTIO N VGA1 Press the ◄► buttons to enter a nd enable or disable the V GA1 source. VGA2 (*) Press the ◄► buttons to enter a nd enable or disable the V GA2 source.
DLP Projector—User’s Manual – 33 – M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified replacement part, which you can order from your local dealer.
DLP Projector—User’s Manual 2. Remove the lamp compartment cover. 3. Disconnect the lamp connector 1 2 4. Remove the two screws from the lamp module.
DLP Projector—User’s Manual 7. Reverse steps 1 to 6 to install the new lamp module. While installing, align the lamp module and ensure it is level to avoid damage.
DLP Projector—User’s Manual Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 1. Press the MENU button to open the OSD menu. 2. Press the cursor ◄► button to move to the Settings 2 menu.
DLP Projector—User’s Manual – 37 – Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn.
DLP Projector—User’s Manual Using the Kensingt on ® Lock & Using the Security Bar Using the Kensington ® Lock If you are concerned about security, attach the proj ector to a permanent obje ct with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensi ngton security cable.
DLP Projector—User’s Manual – 39 – T ROUBLESHOOTING Common problems and solut ions These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved, cont act your dealer for assistance.
DLP Projector—User’s Manual — 40 — LED Error Messages E RROR C ODE M ESSAGES P OWER LED B LUE L AMP LED R ED System Initial Flash OFF Ready to Power on (Standby) ON OFF System Power on Flash O.
DLP Projector—User’s Manual – 41 – Problem: The image is reversed Check the Projection setting on the Settings 1 menu of the OSD. Problem: The image is streaked 1. Set the Frequency and Tracking settings on the Image->Computer menu of the OSD to the default settings.
DLP Projector—User’s Manual — 42 — 5. Have the projector serviced. Problem: The sound is distorted 1. Check the audio cable connection. 2. Test the source audio output with other speakers. 3. Have the projector serviced. Having the Projector Serviced If you are unable to solve the problem, you should hav e the projector serviced.
DLP Projector—User’s Manual – 43 – HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? Recently, HDMI Licensing, LLC announced that cable s would be tested as Standard or High - Speed cables.
DLP Projector—User’s Manual — 44 — S PECIFICATIONS Specifications Model D550 / D552 D55BA D556 / D554 Display type TI DMD 0.55” SVGA Resolution SVGA 800x600 Projection distance 1 ~ 10 m Projection screen size 23" ~ 256" Projection lens Manual Focus/Manual Zoom Zoom ratio 1.
DLP Projector—User’s Manual – 45 – Model D548 / D54HA D551 D553 D555 Display type TI DMD 0.55” SVGA TI DMD 0.55” XGA Resolution SVGA 800x600 XGA 1024x768 Projection distance 1 ~ 10 m Projection screen size 23" ~ 256" Projection lens Manual Focus/Manual Zoom Zoom ratio 1.
DLP Projector—User’s Manual — 46 — Model D557W / D 557WH D560ST Display type TI DMD 0.65” WXGA TI DMD 0.55” SVGA Resolution WXGA 1280 x 800 SVGA 800x600 Projection distance 1 ~ 10 m 0.8~3m Projection screen size 27" ~ 300" 43.7" ~ 164" Projection lens Manual Focus/Manual Zoom Manual Focus Zoom ratio 1.
DLP Projector—User’s Manual Projection Distance vs. Projection Si ze Projection Distance and Size Table D550 / D552 / D556 / D548 / D54HA / D551 /D553 / D555 / D55BA / D554 I MA GE D IAGONA L ( .
DLP Projector—User’s Manual — 48 — D557W / D557W H I MA GE D IAGONA L ( INCH ) I MA GE W IDTH ( INCH ) I MA GE H IGHT ( INCH ) P ROJECTION D ISTANCE ( MM ) F ROM P ROJECTION D ISTANCE ( MM ) TO O FFSET -A ( MM ) 60 50.9 31.8 1990.2 2209.
DLP Projector—User’s Manual – 49 – Timing Mode Table S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB DVI / HDMI NTSC - 15.734 60.0 O - - - PAL/SECAM - 15.625 50.0 O - - - 720 x 400 37.9 85.
DLP Projector—User’s Manual — 50 — S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB DVI / HDMI 1280 x 960 60.0 60.0 - - O O 1280 x 960 85.9 85.0 - - O O 1400 x 1050 65.3 60.0 - - O O 1440 x 900 70.
DLP Projector—User’s Manual Projector Dimensions 274.6mm [10.8"] 212mm [9.346"] 100.3mm [3.95"] 86mm [3.386"] – 51 –.
DLP Projector—User’s Manual — 52 — R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
DLP Projector—User’s Manual – 53 – A PPENDIX I RS-232C Protocol RS232 Setting Baud rate: 9600 Parity check: None Data bit: 8 Stop bit: 1 Flow Control None Minimum delay for next command: 1ms C.
DLP Projector—User’s Manual — 54 — Command Group 01 ASCII HEX Function Description Return Value VXXG0101 56h Xh Xh 47h 30h 31 h 30h 31h 0Dh Get Brightness n=0~100 Pn/F VXXS0101n 56h Xh Xh 53h .
DLP Projector—User’s Manual – 55 – Command Group 03 ASCII HEX Function Description Return Val ue VXXG0301 56h Xh Xh 47h 30h 33h 30h 3 1h 0Dh Get Scaling 0: Fill 1: 4:3 2: 16:9 3 :Letter Box 4 .
DLP Projector—User’s Manual — 56 — Command Group 04 (Remote Control) ASCII HEX Function Description Return Value VXXS0401 56h Xh Xh 53h 30h 34h 30h 31h 0Dh UP arrow P/F VXXS0402 56h Xh Xh 53h .
デバイスVivitek D555の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Vivitek D555をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVivitek D555の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Vivitek D555の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Vivitek D555で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Vivitek D555を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVivitek D555の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Vivitek D555に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVivitek D555デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。