Vulcan-HartメーカーK40DLTの使用説明書/サービス説明書
ページ先へ移動 of 16
INST ALLA TION & OPERA TION MANUAL FORM 35459 (May 201 1) DIRECT STEAM 2/3 JACKETED ST A TIONAR Y AND TIL TING KETTLES MODELS K20DL ML-136081 K40DL ML-136082 K60DL ML-136083 K20DL T ML-136086 K40D.
IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREP ARED FOR PERSONNEL QUALIFIED TO INST ALL PLUMBING AND MUST BE ABLE TO PERFORM THE INITIAL FIELD ST ART -UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death.
— 3 — DIRECT STEAM KETTLES CONTENTS GENERAL ....................................................................................................................... ....................4 INST ALLA TION ..............................................
— 4 — DIRECT STEAM KETTLES INST ALLA TION, OPERA TION AND MAINTENANCE OF KDL AND KDL T SERIES DIRECT STEAM KETTLES SA VE THESE INSTRUCTIONS FOR FUTURE USE GENERAL V ulcan direct steam 2/3 jacketed kettles are produced with quality workmanship and material.
— 5 — DIRECT STEAM KETTLES INST ALLA TION UNP ACKING This kettle was inspected before leaving the factory . The transportation company assumes full responsibility for safe delivery upon acceptance of the shipment. Immediately after unpacking, check for possible shipping damage.
— 6 — DIRECT STEAM KETTLES LOCA TION Plumbing connections must comply with applicable sanitary , safety and plumbing codes. Stationary Kettle Position the kettle in its fi nal location. Check that there are suf fi cient clearances for operating and servicing the kettle, and proper clearance of the cover when raised.
— 7 — DIRECT STEAM KETTLES Tilting Kettle Position the kettle in its fi nal installed location to provide drainage directly below pour path, with suf fi cient rear clearance from the wall to allow the kettle to tilt completely without obstruction.
— 8 — DIRECT STEAM KETTLES INST ALLA TION PROCEDURE Make sure the kettle is in its fi nal location before performing the installation procedure. It may be necessary to increase the height of the kettle when leveling to clear the draw-off valve on tilting kettles.
— 9 — DIRECT STEAM KETTLES Maximum Flow Rate of Dry Steam in Pounds per Hour Supply Pressure Standard Pipe Size 1 / 2 " 3 / 4 "1 " 1 1 / 4 "1 1 / 2 "2 " 5 PSIG 20 40 .
— 10 — DIRECT STEAM KETTLES OPERA TION The kettle and its parts are hot. Use care when operating, cleaning or servicing the kettle. Food products with milk or egg base should be placed into a cold kettle before cooking. A void sudden contact of these food products to a hot kettle surface because they stick to the surface.
— 1 1 — DIRECT STEAM KETTLES ST AINLESS STEEL EQUIPMENT CARE AND CLEANING (Supplied courtesy of NAFEM. For more information, visit their web site at www .nafem.org) Contrary to popular belief, stainless steels ARE susceptible to rusting. Corrosion on metals is everywhere.
— 12 — DIRECT STEAM KETTLES 4. T reat your water . Though this is not always practical, softening hard water can do much to reduce deposits. There are certain fi lters that can be installed to remove distasteful and corrosive elements. T o insure proper water treatment, call a treatment specialist.
— 13 — DIRECT STEAM KETTLES CLEANING The kettle and its parts are hot. Use care when operating, cleaning or servicing the kettle. The kettle interior and exterior should be thoroughly washed after each use when a different food is to be cooked next or when cooking is completed for the day .
— 14 — DIRECT STEAM KETTLES PLUG V AL VE CLEANING INSTRUCTIONS Daily After Use Remove draw-off valve plug for cleaning (Fig. 4). 1. Unscrew the retaining ring and remove it and the bottom washer . 2. Pull the valve plug straight up to remove from valve body .
— 15 — DIRECT STEAM KETTLES MAINTENANCE SERVICE T o obtain service and parts information concerning this unit, contact the V ulcan-Hart Service Agency in your area (refer to listing supplied with the kettle), or contact the V ulcan-Hart Service Department at the address or phone number shown on the front cover of this manual.
— 16 — DIRECT STEAM KETTLES F-35459 (May 201 1) PRINTED IN U.S.A..
デバイスVulcan-Hart K40DLTの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Vulcan-Hart K40DLTをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはVulcan-Hart K40DLTの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Vulcan-Hart K40DLTの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Vulcan-Hart K40DLTで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Vulcan-Hart K40DLTを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はVulcan-Hart K40DLTの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Vulcan-Hart K40DLTに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちVulcan-Hart K40DLTデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
