Wagner SprayTechメーカー292003の使用説明書/サービス説明書
ページ先へ移動 of 20
1 OWNER'S MANUAL Read Rules for Safe Operation and Instructions Carefully Fine Finish ST A TI-KIT CAUTION T.M. VM200 HV I O T0.2A VM200 H V I O T 0 .
1 CONTENTS SAFETY PRECAUTIONS .................................................................... 3-6 SPECIFICA TIONS ................................................................................ 7 INTRODUCTIONS ...................................
1 SAFETY PRECAUTIONS This manual contains information which must be read and understood before using the equipment. When you come to an area which has one of the following symbols, pay particular attention and make certain to heed the safeguard. Important safety information indicates a hazard which may cause serious injury or loss of life.
1 HAZARD WARNING Electrostatic arcing may cause an explosion or fire. Solvent and paint fumes can explode or ignite causing property damage and/or severe injury. PREVENTION • Operator must be grounded. Grounding straps must be used when wearing rubber soled shoes.
1 HAZARD WARNING • Follow the requirements of the Material Safety Data Sheet supplied by the coatings manufacturer. • Exhaust and fresh air introduction must be provided within the spray area to keep the air free of accumula- tions of toxic materials.
1 WARNING PREVENTION HAZARD General • All accessories must be rated at or above the maximum pressure rating of spray pump (includes spray tips, guns, extensions and fluid hose. • If you are injected, see a physician immediately. Injection (Con't) DO NOT TREAT AS A SIMPLE CUT! It can lead to amputation.
1 SPECIFICA TIONS GM2000 EAC SPRA YGUN (P/N 0179673) Air Pressure, max. 145 psi Material Pressure, max. 3625 psi Air Volume 10 CFM@ 45 PSI Material Volume Varies due to Tip size Air Connector 1/4 inch Material Connector NPS 1/4 Length 11.8 inches Height 10 inches Weight 21 oz.
1 Figure 1 Figure 2 HV GM 2000 O I T0.2A VM200 GROUND CONNECTION FUSE ON - OFF SWITCH RED HIGH VOLTAGE LAMP HIGH VOLTAGE CABLE SOCKET GENERAL DESCRIPTION GM2000 EAC SPRA Y GUN The GM2000 EAC Electrostatic Air Coat Spraygun is very light and easy to service.
1 TYPICAL MOUNTING AR- RANGEMENT W AGNER AIRLESS SPRA YER MOUNTING INSTRUCTIONS 1. Use the allen wrench provided, attach the mounting bracket (1) to the power pack (2) with the 2.4mm lockwashers (3) and socket head screws (4). 2. Place the power pack/mounting bracket assembly on any 1" diameter tube, preferably as illustrated below.
1 Power cord ground must remain intact. Do not clip off ground pole on plug to fit a non- grounded socket. Static build up will result which may cause an explosion. WARNING Figure 4 SET -UP SET -UP VM 200 POWER PACK: 1. GM 2000 EAC Socket Outlet 2. Ground Connection Knob 3.
1 CLEAN UP WHEN CLEANING THE ELECTROST A TIC SYSTEM, THESE SAFETY PROCEDURES MUST BE FOLLOWED. FAILURE T O FOL- LOW THESE PROCEDURES MA Y RESUL T IN AN EXPLOSION/FIRE. • Turn power pack to the “OFF” position and unplug from power source before starting to clean.
1 TIP CHANGE CHANGING THE ROUND SPRA Y TIP 1. Screw out spray tip (B) with tip wrench (A). (See Fig.5) 2. Attach desired spray tip and tighten with tip wrench. CLEANING OF THE FLA T SPRA Y TIP • Remove air cap (H). (See Fig. 8) • Remove flat spray tip (G) and clean it.
1 VA L VE SEAL REPLACEMENT To replace valve seals you must remove the entire valve rod. 1. Actuate trigger (3) and unscrew trigger lock knob (2), remove the compression spring. Fig. 11 2. Remove screws holding trigger asembly in place and remove trigger (3).
1 14 Problem • No green light on Power Pack • Gun on-off switch performing opposite. • No red light on Power Pack. • Spray pattern not even; unsymmetrical or poor atomization. • Spray pattern is correct, but there is no wraparound. • Dead outlet.
1 TROUBLESHOOTING Problem • Air leaking at tip without pulling trigger. • Air leaks between gun body and gun barrel. • No air at tip when trigger is pulled. • Air valve is faulty. • Gun Barrel Nut. • Air hose not connected. • No air supply • Wrong tip body fitted • Round tip nut screwed down too hard.
1 Figure 9 16.
1 GM 2000 EAC Item Description Part Number 1 Spray gun barrel 0179500 2 Bushing 0128336 3 Screw countersunk 0179354 4 Type plate 9900962 5 Screw flathead 9900810 6 O-ring 9971003 7 Knob, Air Adjustmen.
1 Flat T ip Part Tip Orifice Size Fan Number Marking (Inch) Width 0128550 9/15 .009 15 ° 0128216 9/20 .009 20 ° 0128552 11/15 .011 15 ° 0128217 11/20 .011 20 ° 0128201 11/50 .011 50 ° 0128554 13/15 .013 15 ° 0128218 13/20 .013 20 ° 0128212 13/50 .
19.
LIMITED W ARRANTY ELECTROST A TIC P AINT SPRA Y EQUIPMENT To validate this warranty, the completed registration card must be mailed within one week of the date of purchase to Wagner Spray Tech Corporation.
デバイスWagner SprayTech 292003の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Wagner SprayTech 292003をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWagner SprayTech 292003の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wagner SprayTech 292003の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wagner SprayTech 292003で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wagner SprayTech 292003を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWagner SprayTech 292003の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wagner SprayTech 292003に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWagner SprayTech 292003デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。