Wagner SprayTechメーカー558018の使用説明書/サービス説明書
ページ先へ移動 of 32
Edition 5 / 2014 0558 978L ProSpray 3.39 Model: 0558018 Original operating manual GB Operating manual ProSpray 3.39 Airless high-pressure spraying unit.
2 ProSpra y 3.39 GB Warning! Attention: Danger of injury by injection! Airless units develop extremely high spraying pressures. Be safety conscious! 1 2 3 Never put your ngers, hands or any other parts of the body into the spray jet! Never point the spray gun at yourself, other persons or animals.
ProSpra y 3.39 3 GB Contents Contents Page 1. Safety regulations for Airless spraying ...................................... 4 1.1 Explanation of symbols used .............................................................. 4 1.2 Electric Safety .......
4 ProSpra y 3.39 GB Safety Regulations 1. Safety regulations for Airless spraying 1.1 Explanation of symbols used This manual contains information that must be read and understood before using the equipment. When you come to an area that has one of the following symbols, pay particular attention and make certain to heed the safeguard.
ProSpra y 3.39 5 GB Safety regulations • Followmaterialandsolventmanufacturer’swarningsand instructions.Befamiliarwiththecoatingmaterial’sMSDS sheet and technical information to ensure safe use.
6 ProSpra y 3.39 GB General view of application Description of unit 2. General view of application 2.1 Application 2.2 Coating materials Processible coating materials i Pay attention to the Airless quality of the coating materials to be processed.
ProSpra y 3.39 7 GB Description of unit 10 11 1 2 3 6 8 9 7 12 5 4 13 16 15 14 17 3.3 Legend for explanatory diagram ProSpray 3.39 1 Spray gun 2 Hose to hose whip connector (3/8” x 1/2”) 3 Whip hose to gun connector (1/4” x 3/8”) 4 High pressure hose, 13 mm x 15 m (1/2” x 50 ft) 5 High pressure whip hose, 10 mm x 2.
8 ProSpra y 3.39 GB Description of unit 3.5 Technical data Voltage: 220-240VoltAC,50/60Hz Max. current consumption: 9.5A@230VAC Power cord: 3 x 1.5 mm 2 – 6 m Acceptance capacity: 1650 Watt Max. operating pressure: 221 bar (22,1 MPa) Volume ow at 12 MPa (120 bar) with water: 5.
ProSpra y 3.39 9 GB Starting operation 4. Starting operation 4.1 High-pressure hose, spray gun and separating oil 1. Screw the 15 m high-pressure hose (2) to the coating material outlet (Fig. 4, Item 1). 2. Thread the double tting into the other end of the high- pressure hose.
10 ProSpra y 3.39 GB Starting operation Solid Green When the pressure indicator is solid green, the sprayer is operating between 12 MPa (120 bar) and 23 MPa (230 bar).
ProSpra y 3.39 11 GB Starting operation 4.7 Digital Electronic Spray Control (DESC) The Digital Electronic Spray Control (DESC) increases the functionality of the sprayer. It is installed directly below the pressure control knob on the control panel. It consists of a display and four function keys.
12 ProSpra y 3.39 GB Starting operation Spraying technique Security Code Screen SECURITY CODE CHANGE-2 MENU-1 The Security Code screen allows the user to set a four digit security code to prevent unauthorizeduseofthesprayer.
ProSpra y 3.39 13 GB Handling the high-pressure hose Cleaning the unit (shutting down) 6. Handling the high-pressure hose The unit is equipped with a high-pressure hose specially suited for piston pumps. Danger of injury through leaking high-pressure hose.
8.2 Cleaning the high-pressure lter Clean the lter cartridge regularly. A soiled or clogged high-pressure lter can cause a poor spray pattern or a clogged tip. 1. Turnthepressureregulatorknobintotheblackzoneuntilit stops (no pressure).
ProSpra y 3.39 15 GB Remedy in case of faults Digital Electronic Spray Control (DESC) Error Messages The following error message screens appear whenever the Digital Electronic Spray Control (DESC) detects a problem with the sprayer. Once a problem occurs and the error message appears, the sprayer will shut down.
16 ProSpra y 3.39 GB Servicing Repairs at the unit 10. Servicing 10.1 General servicing Servicing of the unit should be carried out once annually by the WAGNER service. 1. Check high-pressure hoses, device connecting line and plug for damage. 2. Check the inlet valve, outlet valve and lter for wear.
ProSpra y 3.39 17 GB Repairs at the unit 15. Clean all the parts with the corresponding cleaning agent. Check outlet valve housing (9), outlet valve seat (15), outlet valve ball (13) and upper ball guide (12) for wear and replace parts if necessary. If the worn outlet valve seat (15) is unused on one side, install it the other way around.
18 ProSpra y 3.39 GB Repairs at the unit 19. Insert upper packing (Fig. 17) with O-ring (1) and protruding lip (2) downward. 1 2 20. Insert upper support ring (9) on top of the upper packing (10) 21. Thread the upper seal retainer (8) into the upper housing (2).
ProSpra y 3.39 19 GB Appendix 12. Appendix 12.1 Selection of tip To achieve faultless and rational working, the selection of the tip is of the greatest importance. In many cases the correct tip can only be determined by means of a spraying test. Some rules for this: The spray jet must be even.
20 ProSpra y 3.39 GB Appendix 12.4 Airless tip table Wagner TradeTip 3 tip up to 270 bar (27 MPa) without tip Fthread(11/16-16UN) for W agner spra y guns Order no . 0289391 without tip Gthread(7/8-14UN) for Graco/T itan spray guns Order no .
ProSpra y 3.39 21 GB Appendix Application Tip marking Spray angle Bore inch / mm Spraying width mm 1) Gun lter Order no . Roof coatings 223 323 423 523 623 723 823 20° 30° 40° 50° 60° 70° 80° 0.023 / 0.58 0.023 / 0.58 0.023 / 0.58 0.023 / 0.
22 ProSpra y 3.39 GB Appendix 12.5 TempSpray The paint material is heated to the required temperature uniformly by an electric heating element, which is located inside the hose (regulated from20°Cto60°C).
ProSpra y 3.39 23 GB Appendix 12.6 Pump-Runner (Order No. 2306987) Universalaccessoriesforcleaning,cleantransportationandpreservationofthepumpunit.
24 ProSpra y 3.39 Accessories illustration ProSpray 3.39 3 1 5 8 2 4 7 9 10 6.
ProSpra y 3.39 25 Item Part No. Description 1 0296 388 Spray gun AG 08, F-thread 0296 386 Spray gun AG 08, G-thread 0502 166 Spray gun AG 14, F-thread 0502 119 Spray gun AG 14, G-thread 2 0296 441 Pol.
26 ProSpra y 3.39 Spare Parts List ProSpray 3.39 59 60 61 1 3 4 38 5 6 9 8 35 2 36 7 2 10 11 12 13 17 16 14 15 18 19 20 21 22 23 24 26 27 28 30 31 32 33 29 25 37 39 41 34 40 43 42 46 44 45 47 48 49 Ma.
ProSpra y 3.39 27 Item Part No. Description 1 0290 271 Motor shroud 2 0508 559 Screw (2) 3 0558 497 Belly pan assembly 4 9802 266 Screw (2) 5 0290 228 Door 6 0509 218 Screw (2) 7 0290 253 Grommit 8 05.
28 ProSpra y 3.39 Item Part No. Description 1 0558 419 Cylinder 2 0524 905 Stopping spacer 3 0524 906 Extension bushing 4 0558 570A Piston extension 5 0558 422 Extension slider 6 9832 126 Connecting p.
ProSpra y 3.39 29 Spare Parts List ProSpray 3.39 16 17 4 5 6 8 7 9 13 12 14 15 10 11 1 2 3 18 19 20 Drive Assembly Item Part No. Description 1 0558 572A Slider assembly 2 0507 767 Screw (4) 3 0290 272.
30 ProSpra y 3.39 15 1 2 3 4 5 7 6 8 9 17 16 18 13 14 15 12 11 10 19 20 Filter assembly Spare Parts List ProSpray 3.39 1 15 2 3 4 5 6 7 8 9 10 11 12 13 14 Item Part No.
ProSpra y 3.39 31 Important notes on product liability As a result of an EC regulation being eective as from January 1, 1990, the manufacturer shall only be liable for his product if all parts come from him or are released by him, and if the devices are properly mounted and operated.
32 ProSpra y 3.39 www.wagner-group.com A J. W agner Ges.m.b.H. Ottogasse 2/20 2333 Leopoldsdorf Österreich T el. +43/ 2235 / 44 158 T elefax +43/ 2235 / 44 163 oce@wagner-group .at DK W agner Sprayt ech Scandinavia A/S Helgeshøj Allé 28 2630 T aastrup Denmark T el.
デバイスWagner SprayTech 558018の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Wagner SprayTech 558018をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWagner SprayTech 558018の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wagner SprayTech 558018の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wagner SprayTech 558018で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wagner SprayTech 558018を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWagner SprayTech 558018の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wagner SprayTech 558018に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWagner SprayTech 558018デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。