Wagner SprayTechメーカー558046の使用説明書/サービス説明書
ページ先へ移動 of 28
Edition 9 / 2014 0558 932J ProSpray 3.21 GB Operating manual ProSpray 3.21 Airless high-pressure spraying unit Models: 0558019 0558046 Original operating manual.
2 ProSpra y 3.21 GB Warning! Attention: Danger of injury by injection! Airless units develop extremely high spraying pressures. Be safety conscious! 1 2 3 Never put your ngers, hands or any other parts of the body into the spray jet! Never point the spray gun at yourself, other persons or animals.
ProSpra y 3.21 3 GB Contents Contents Page 1. Safety regulations for Airless spraying ...................................... 4 1.1 Explanation of symbols used .............................................................. 4 1.2 Electric Safety .......
4 ProSpra y 3.21 GB Safety Regulations 1. Safety regulations for Airless spraying 1.1 Explanation of symbols used This manual contains information that must be read and understood before using the equipment. When you come to an area that has one of the following symbols, pay particular attention and make certain to heed the safeguard.
ProSpra y 3.21 5 GB Safety regulations • Followmaterialandsolventmanufacturer’swarningsand instructions.Befamiliarwiththecoatingmaterial’sMSDS sheet and technical information to ensure safe use.
6 ProSpra y 3.21 GB General view of application Description of unit 2. General view of application 2.1 Application 2.2 Coating materials Processible coating materials i Pay attention to the Airless quality of the coating materials to be processed.
ProSpra y 3.21 7 GB Description of unit 14 13 12 11 15 16 7 1 3 4 6 5 9 10 2 8 3.3 Legend for explanatory diagram ProSpray 3.21 3 Return hose 4 Suction hose 5 Frame 6 Drip cup 7 Power cord 8 Relief va.
8 ProSpra y 3.21 GB Description of unit Starting operation 3.5 Technical data Voltage: 100-120Volt,50/60Hz Max. current consumption: 9.0 A Power cord: 3 x 1.5 mm 2 – 6 m or 2.5 m Acceptance capacity: 900 Watt Max. operating pressure: 221 bar (22.
ProSpra y 3.21 9 GB Starting operation 6 4.2 Control Panel Indicators The following is a description of the control panel indicators. Pr essure Indicato r Ser vice Indicato r Pressure Indicator The pressure indicator shows the current operating pressure of the sprayer.
10 ProSpra y 3.21 GB Starting operation Spraying technique 4.5 Cleaning preserving agent when starting-up of operation initially 1. Immerse the suction tube (Fig. 6, Item 1) and return hose (2) into a container with a suitable cleaning agent. 2. Turn the pressure control knob counterclockwise (3) to minimum pressure.
ProSpra y 3.21 11 GB Handling the high-pressure hose Cleaning the unit (shutting down) 6. Handling the high-pressure hose The unit is equipped with a high-pressure hose specially suited for piston pumps. Danger of injury through leaking high-pressure hose.
12 ProSpra y 3.21 GB Cleaning the unit (shutting down) 8.2 Suction lter i A clean suction lter always guarantees maximum feed quantity, constant spraying pressure and problem-free functioning of the unit. 1. Screw o the lter (Fig. 7) from suction pipe.
ProSpra y 3.21 13 GB Remedy in case of faults Type of malfunction A. Unitdoesnotstart B. Unitdoesnotdrawinmaterial C. Unitdrawsinmaterial,butthe pressure does not build up D. Coating material exits at the top of the uid section E.
14 ProSpra y 3.21 GB Servicing Repairs at the unit 10. Servicing 10.1 General servicing Servicing of the unit should be carried out once annually by the WAGNER service. 1. Check high-pressure hoses, device connecting line and plug for damage. 2. Check the inlet valve, outlet valve and lter for wear.
ProSpra y 3.21 15 GB Repairs at the unit 11 10 12 13 9 8 11.3 Packings 1. Remove inlet valve housing in accordance with the steps in Chapter 11.2, Page 14. 2. It is not necessary to remove the outlet valve. 3. Unscrewbothcylinderheadscrews(Fig.
16 ProSpra y 3.21 GB Repairs at the unit 18. Slide the top of the piston (3) into the T-slot (9) on the slider assembly (4). 19. Position the pump manifold (2) underneath the gear unit housing and push up until it rests against the gear unit housing. 20.
ProSpra y 3.21 17 GB Appendix 12. Appendix 12.1 Selection of tip To achieve faultless and rational working, the selection of the tip is of the greatest importance. In many cases the correct tip can only be determined by means of a spraying test. Some rules for this: The spray jet must be even.
18 ProSpra y 3.21 GB Appendix Application Tip marking Spray angle Bore (inch / mm) Spraying width mm 1) Order no. Natural paints Clear paints Oils Spray gun lter “RED” 407 40° 0.007 / 0.18 160 0552 407 507 50° 0.007 / 0.18 190 ––––––– 209 20° 0.
ProSpra y 3.21 19 GB Appendix 12.5 Pump-Runner (Order No. 2306987) Universalaccessoriesforcleaning,cleantransportationandpreservationofthepumpunit.
20 ProSpra y 3.21 Accessories illustration ProSpray 3.21 3 1 5 7 9 2 4 6 8.
ProSpra y 3.21 21 Item Part No. Description 1 0296 388 Spray gun AG 08, F-thread 0296 386 Spray gun AG 08, G-thread 0502 166 Spray gun AG 14, F-thread 0502 119 Spray gun AG 14, G-thread 2 0296 441 Pol.
22 ProSpra y 3.21 Spare parts list ProSpray 3.21 28 30 29 31 32 33 34 35 1 19 18 25 49 6 26 43 21 22 23 24 20 45 46 47 48 7 5 9 10 11 8 27 44 2 3 4 37 36 40 38 39 41 42 14 15 16 17 12 13 Main Assembly 0558 466 ~110V 6 m 0290 281 ~120V 2.
ProSpra y 3.21 23 Item Part No. Description 1 0290 230 Motor shroud 2 9805 403 Set screw 3 9810 103 Nut 4 0524 353 Nut 5 9800 319 Screw (2) 6 9822 627 Washer (2) 7 0558 332A Belly pan assembly (includ.
24 ProSpra y 3.21 Spare parts list ProSpray 3.21 24 23 25 26 27 28 29 30 31 32 33 34 1 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 2 3 4 5 7 6 Fluid section Item Part No.
ProSpra y 3.21 25 Spare parts list ProSpray 3.21 3 4 2 1 5 6 7 8 9 10 11 8 12 Drive Assembly Item Part No. Description 1 0524 637A Housing assembly 2 0509 121 2nd stage gear 3 0558 373 Motorassembl.
26 ProSpra y 3.21 1 3 2 4 5 ProSpray 3.21 1 4 56 7 8 9 2 3 10 Stand Spare parts list Item Part No. Description 1 9805 367 Screw (3) 2 0290 215 Drip cup 3 0290 211 Leg, right 4 0294 635 Plug 5 0290 214.
ProSpra y 3.21 27 GB Important notes on product liability As a result of an EC regulation being eective as from January 1, 1990, the manufacturer shall only be liable for his product if all parts come from him or are released by him, and if the devices are properly mounted and operated.
28 ProSpra y 3.21 www.wagner-group.com A J. W agner Ges.m.b.H. Ottogasse 2/20 2333 Leopoldsdorf Österreich T el. +43/ 2235 / 44 158 T elefax +43/ 2235 / 44 163 oce@wagner-group .at DK W agner Sprayt ech Scandinavia A/S Helgeshøj Allé 28 2630 T aastrup Denmark T el.
デバイスWagner SprayTech 558046の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Wagner SprayTech 558046をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWagner SprayTech 558046の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wagner SprayTech 558046の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wagner SprayTech 558046で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wagner SprayTech 558046を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWagner SprayTech 558046の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wagner SprayTech 558046に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWagner SprayTech 558046デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。