Wayne-DaltonメーカーDS-100の使用説明書/サービス説明書
ページ先へ移動 of 15
IMPORTANT NOTICE !! Read the enclosed instructions carefully befo re attempting to install this door. Pay close attention to all warnings and important safety notices.
2 CAUTION CAUTION WARNING IMPORTANT! HINT: NOTE: IMPORTANT SAFETY NOTICES Read the enclosed instructions carefully befo re attempting installation. If there are any questions about any of the procedures, do not perform the work. Instead, have a trained door technician do the installation or repairs.
3 INTRODUCTION This manual's m ain function is to assist the installer in correctly installing the doors to ensure safe operation. Compliance with building codes, enforced in your area, is required. All Wayne-Dalton DS-50, DS-75, and DS-100 Mini Roll-Up Doors follow these general instructions.
4 STEP 1 UNPACKING DOORS Before removing the door from any packaging, inspect the packaging for visible signs of damage. If damage is not ed, file a freight claim with the freight company imm ediately. Remove the door from the packaging. Do not cut tape that holds door in a roll.
5 STEP 3 INSTALLING GUIDES Position the left hand guide 3/8” from the edge of the left hand jamb a nd loosely clamp in place. Using a level, adjust the guide so that it is plumb and tighten the clamp. Measure the exact curtain width of the door and add 7/8” to obtain the inside of guide to inside of guide measurement.
6 HINT: STEP 5 LIFTING THE CURTAIN ASSEMBLY Curtain assembly is heavy . Allowing curtain assembly to fall while lifting, could result in severe or fatal injury. To avoid severe or fatal injury, never walk, stand, or work below curtain assembly before it is secured to support brackets.
7 STEP 7 PRE-TENSIONING THE DOOR SPRING Spring tension can cause curtain assembly to rotate rapidly , possibly resulting in severe or fatal injury . To prevent such injury, securely hold curtain assembly to prevent rotating.
8 STEP 9 CHECKING AND ADJUSTING SPRING BALANCE Spring tension can cause curtain assembly to rotate rapidly , possibly resulting in severe or fatal injury . To prevent such injury, securely hold curtain assembly to prevent rotating. Move the door up and down to check for proper spring tension.
9 II: DS-50 & 100 ‘C’ Stop-Clip Attachment: For doors with an aluminum bottom bar, a ‘C’ stop-clip will need to be installed. Only one bolt is required to secure the stop-clip to the bottom bar when attaching a lift handle on that side. Repeat assembly procedure for both sides.
10 STEP 12 INSTALLING THE OPTIONAL TENSI ON-PRO SPRING ADJUSTMENT BRACKET STEP #12a : Install the Tension-Pro™ bracket on the left hand side of the curtain assembly per STEP #4 & #5 in this manual. Insert cotter pin through hole in the axle end.
11 To Increase Spring Tension : Move the door to the fully open position and place clamps on the guides to prevent door from closing. Using a large pipe wrench, grip the tensi oning hex plat e and rotate the ratchet gear assembly in the direction indicated above until an audible “CLICK” is heard (one gear tooth).
12 Roll-Up Sheet Door LIMITED WARRANTY Wayne-Dalton P.O. Box 67- Mt. Hope, Ohio 44660 The Manufacturer warrants the ROLL-UP SHEET DOOR and hardwa re fittings for a period of ONE YEAR from the tim e of deliv ery a gainst any defect s in workmanship or m aterial.
13 Limited Warranty for Paint on the following Wayne-Dalton products Roll-Up Doors Model Nos. • DS 50, • DS 75, • DS 100, • DS 200, • DS 350 Interior Systems Wayne-Dalton Door & Systems Div.
14 This limited warra nty applies to the effects of weathe ri ng and does not apply to other causes of degradation, such as in the case of (by way of example and without limitation): (1) Painted surfa.
15 F. Other Terms. This limited warranty is made to the Original Own er, exclusively, and not to anyone who or which subsequently owns or possesses the structure where the Product has been installed. This limited warranty is not assignable or otherwise transferable.
デバイスWayne-Dalton DS-100の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Wayne-Dalton DS-100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWayne-Dalton DS-100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wayne-Dalton DS-100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wayne-Dalton DS-100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wayne-Dalton DS-100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWayne-Dalton DS-100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wayne-Dalton DS-100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWayne-Dalton DS-100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
