Weed Eaterメーカー177599の使用説明書/サービス説明書
ページ先へ移動 of 48
MODEL NO. SGT18H46A 18.0 HP 46 Inch Lawn T ractor For Parts and Service, contact our authorized distributor: call 1-800-849-1297 For T echnical Assistance: call 1-800-829-5886 177599 Rev .
2 I . GENERAL OPERATION • Read, understand, and follow all instructions in the manual and on the machine before starting. • Only allow responsible adults, who are familiar with the instructions, to operate the machine. • Clear the area of objects such as rocks, toys, wire, etc.
3 • Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off. • Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.
4 PRODUCT SPECIFICA TIONS GASOLINE CAPACITY 3.5 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF-SJ): SAE 30 (above 32 ° F) SAE 5W-30 (below 32 ° F) OIL CAPACITY: W/FILTER: 5 PINTS W/O FILTER: 4.5 PINTS SPARK PLUG: CHAMPION RN4C (GAP: .030") GROUND SPEED (MPH): FORWARD: 5.
5 UNASSEMBLED P ARTS Steering Wheel Steering Wheel Insert (1) Washer 17/32 x 1-3/16 x 12 Gauge Seat (2) Keys Slope Sheet Key (3) Retainer Springs (double loop) (4) Retainer Springs (single loop) (2) F.
6 ASSEMBL Y T OOLS REQUIRED FOR ASSEMBL Y A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) 9/16" wrench Pliers (2) 7/16" wrenches Tire pressure gauge (2) .
7 ASSEMBL Y TO ROLL TRACTOR OFF SKID (See Operation section page 11 for location and function of controls) • Press lift lever plunger and raise attachment lift lever to its highest position. • Release parking brake by depressing clutch/brake pedal.
8 INSTALL MOWER AND DRIVE BELT (See Figs. 5 and 6) Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage parking brake. • Cut and remove ties securing anti-sway bar and belts. Swing anti-sway bar to left side of mower deck.
9 CHECKLIST BEFORE YOU OPERATE AND ENJOY YOUR NEW TRAC- TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed. ✓ No remaining loose parts in carton.
10 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR WARNING REVERSE FORWARD FAST SLOW ENGINE ON EN.
11 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
12 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
13 OPERA TION TO OPERATE ON HILLS CAUTION: Do not drive up or down hills with slopes greater than 15 ° and do not drive across any slope. • Choose the slowest speed before starting up or down hills. • Avoid stopping or changing speed on hills. • If slowing is necessary, move throttle control lever to slower position.
14 OPERA TION TO START ENGINE (See Fig. 6) When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Be sure freewheel control is in the transmission engaged position.
15 FIG. 11 OPERA TION PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run- ning. To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time.
16 CUST OMER RESPONSIBILITIES B E F O R E E A C H U S E T R A C T 0 R Adjust Motion Drive Belt(s) Tension Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change.
17 CUST OMER RESPONSIBILITIES BLADE REMOVAL (See Fig. 12) • Raise mower to highest position to allow access to blades. • Remove hex bolt, lock washer and flat washer securing blade. • Install new or resharpened blade with trailing edge up towards deck as shown.
18 CUST OMER RESPONSIBILITIES ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SF-SJ. Select the oil ’ s SAE viscosity grade according to your expected operating temperature.
19 CUST OMER RESPONSIBILITIES MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
20 SER VICE AND ADJUSTMENTS FIG. 17 CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress clutch/brake pedal fully and set parking brake. • Place motion control lever in neutral (N) position. • Place attachment clutch in “ DISENGAGED ” position.
21 SER VICE AND ADJUSTMENTS NUT "E" "D" "D" MANDREL FIG. 20 NUT "F" FRONT LINKS FIG. 21 FRONT-TO-BACK ADJUSTMENT (See Figs.
22 SER VICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 23) Park the tractor on level surface. Engage parking brake. • Remove mower drive belt (See “ TO REPLACE MOWER DRIVE BELT ” in this section of this manual). • Remove mower (See “ TO REMOVE MOWER ” in this section of this manual).
23 TO ADJUST STEERING WHEEL ALIGNMENT If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual. FRONT WHEEL TOE-IN/CAMBER The front wheel toe-in and camber are not adjustable on your tractor.
24 TO ADJUST CARBURETOR The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.
25 ST ORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
26 Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “ CHOKED ” properly. 2. See “ TO START ENGINE ” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug.
27 PRO BLE M CAUSE CORRECTION Engine continues to run 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves corrected, contact an authorized service center/ seat with attachment department.
28 SER VICE NOTES.
29 TRACTOR - - MODEL NUMBER SGT18H46A SCHEMA TIC BATTERY FUSE IGNITION SWITCH RED RED RED BLACK IGNITION UNIT HEADLIGHTS REMOVABLE CONNECTIONS BLACK BLACK BLACK WHITE WHITE WHITE RED BLACK ORANGE BLAC.
30 28 29 26 24 42 43 25 41 27 27 40 33 30 12 12 11 10 8 2 1 27 55 16 22 21 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A ELECTRICAL 16 D . C . A M P E R E S 45.
31 KEY P ART N O . N O . DESCRIPTION 1 163465 B a t t e r y , 1 2 V o lt, 28 Amp 2 74760412 Bolt, Hex Head 1/4-20 UNC x 3/4 8 7603J Tray, Battery 1 0 145211 B o lt, Battery Front 1/4-20 x 7.
32 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A CHASSIS 59 3 2 35 3 35 3 26 33 10 26 34 1 11 9 66 8 36 87 36 36 29 119 115 71 90 125 28 50 86 120 121 122 17 123 124 19 6 209 3 153 209 209 209 64 .
33 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A CHASSIS 1 169831 Chassis Wldmt. 2 169061 D r awbar Stretch 94 3 17060612 Screw 3/8-16 x 3/4 6 155923 Saddle Flat Lt 8 126471X Clip Insulator 9 170119 Dash 1 0 72140608 B o l t RdHd Sqnk.
34 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A DRIVE 81 21 8 10 169 82 156 165 168 166 163 14 159 161 198 158 164 83 162 171 66 29 28 51 110 110 30 51 110 110 59 51 42 31 38 61 41 42 40 73 103 1.
35 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A DRIVE KEY P ART N O . N O . DESCRIPTION KEY P ART N O . N O . DESCRIPTION 1 - - - - - - - Transaxle, Hydro Gear Model 325- 3000 (Order Parts From T.
36 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A STEERING ASSEMBL Y 62 38 38 12 39 1 41 42 37 36 37 5 9 5 7 7 9 4 3 32 43 6 43 8 18 19 22 27 23 11 56 40 66 29 25 79 8 10 40 11 8 6 9 46 46 8 6 9 2 .
37 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A STEERING ASSEMBL Y 1 140044X428 W heel Steering Auto Black 2 154427 Axle Asm Front 3 156486 S p i n d l e Asm Lh 4 157475 S pindle Asm Rh 5 6266H B.
38 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A ENGINE 32 31 34 33 37 33 41 40 39 2 1 OPTIONAL EQUIPMENT Spark Arrester 29 26 25 4 23 45 8 10 62 6 5 72 13 99 45 100 45 14 38 105 16 105 3 81 107 1.
39 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A ENGINE KEY P ART N O . N O . DESCRIPTION 1 176174 Control, Throttle 2 17720410 Screw, Hex Head, Thread Cutting 1/4-20 x 5/8 3 - - - - - - - Engine,.
40 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A MOWER DECK 33 41 42 49 36 37 43 40 46 45 50 44 33 30 30 32 21 21 22 23 24 25 26 20 27 28 29 18 18 21 34 132 31 44 35 130 62 72 52 38 1 134 133 82 3.
41 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A MOWER DECK KEY P ART N O . N O . DESCRIPTION KEY P ART N O . N O . DESCRIPTION 1 156948 D e c k A s m . , Mower 46" 3 138457 Bracket Asm., Sway Bar 5 4939M R e t a in e r S pr i n g 6 130832 Arm, Suspension, Rear (Sway Bar) 8 850857 B o lt, Patched 3/8-24 x 1-1/4 Gr.
42 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A MOWER LIFT 36 15 20 16 17 18 20 20 15 20 46 47 23 24 25 27 28 29 37 41 40 38 12 11 31 32 31 32 19 19 13 13 13 13 42 43 39 44 30 49 26 50 6 1 14 2 7.
43 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A MOWER LIFT 1 121006X Rod Assembly, Lever 2 159188 Shaft Assembly, Lift 6 74780624 Bolt, Hex Head, Fin.
44 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A SEA T ASSEMBL Y KEY P AR T N O . N O . DESCRIPTION 1 140118 Seat 2 140551 Pivot Bracket, Seat 5 145006 Clip, Push-in Hinged 6 73800600 Nut, Lock He.
45 REP AIR P ARTS TRACTOR - - MODEL NUMBER SGT18H46A DECALS 3 4 11 7 10 13 13 8 KEY P ART N O . N O . DESCRIPTION KEY P ART N O . N O . DESCRIPTION 1 171448 Decal Fender 2 164022 Decal Side Panel 3 17.
46 LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship.
47 15 MAX. SIGHT AND HOLD THIS LEVEL WITH SKY LINE OR TREE. CUT OUT ON DOTTED LINES THIS IS A 15 SLOPE SIGHTING GUIDE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION Operate your Tractor up and down the face of slopes (not greater than 15 ), never across the face.
®.
デバイスWeed Eater 177599の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Weed Eater 177599をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeed Eater 177599の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weed Eater 177599の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weed Eater 177599で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weed Eater 177599を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeed Eater 177599の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weed Eater 177599に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeed Eater 177599デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。