Weiderメーカー831.15395.0の使用説明書/サービス説明書
ページ先へ移動 of 24
CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. 831.15395.0 S erial No. Write the serial number in the s pace above for future reference. Serial Number Decal (under seat) RESIST ANCE SYSTEM EXERCISER User ’ s Manual Sears, Roebuck and Co.
2 W ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual before u sing the resistance system. Use the resist- ance system only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the resistance system are adequately informed of all precautions.
4 T op Frame High Pulley Lat T ower Backrest Storage Knob Fulcrum Knob Upright Low Pulley Base Plate Leg Lever Seat Knob Seat Resistance Bars “U”-Channel BEFORE YOU BEGIN Thank you for selecting the innovative MAX by WEIDER ™ resistance system.
1 1. Press two 2” Square Inner Caps (98) into the Base (1). Attach two Plastic Feet (53) and two Large Plastic Feet (102) to the Base (1) with four #8 x 3/4” T ek Screws (62).
6 2. Attach a Wheel (31) to the outside of the Base (1) with a 3/8” x 4 1/4” Bolt (81), three 3/8” W ashers ( 75), and a 3/8” Nylon Jamnut (103). D o not overtighten the Jamnut; the Wheel must be a ble to turn easily . Attach the other Wheel (not shown) in the same manner .
7 8. Attach the Leg Lever Bumper (55) to the Front Leg (6) with a #8 x 3/4” T ek Screw (62). Press two 1 3/4” Square Inner Caps (42) into the Leg Lever (7). Lubricate a 3/8” x 2 3/4” Button Head Bolt (64) with grease. Orient the Leg Lever (7) with the slot on the side shown.
8 9. Attach two .34” Metal Spacers (97), a 2.3” Metal Spacer (39), and two Bearing Wheels (46) to one e nd of the Seat Carriage (12) with a 5/16” x 4” Bolt (60) and a 5/16” Nylon Jamnut (65) as s hown.
9 14. Insert the rod on the Backrest Frame (15) into the slot in the Seat Carriage (12). Hold the Backrest Frame vertically over the Seat Carriage and slide the rod into the slot, as shown in the inset drawing. 14 15 15 12 12 Rod Slot Rod 13. Orient the Backrest (14) and the Backrest Backing (8) as shown.
10 19. Attach a Pulley Housing (94) to the indicated “U”- channel on the 10-Pound Center Resistance Bar (44) with a 3/8” x 4” Bolt (66) and a 3/8” Nylon Locknut (76).
1 1 23 80 Rod 28 71 103 11 21. Attach a Pulley Housing (94) to the indicated “U”- channel on the 10-Pound Center Res ist ance Ba r (44) with a 3/8” x 4” Bolt (66) and a 3/8” Nylon Locknut (76). Wrap the Long Cable (80) around a 90mm Pulley (28).
12 27. Slide the four Foam Pads (26) onto the tubes on the Front Leg (6) and the Leg Lever (7). Press four 1 1/4” Round Inner Caps (78) into the ends of the tubes. 28. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENTS, beginning on the following page.
This section explains how to adjust the resistance system. See the EXERCISE GUIDELINES on page 17 for important information about how to get the most benefit from your exercise program. Also, refer to the accompa- n ying exercise guide to see the correct form for each exercise.
14 4 9 80 A TT ACHING THE ACCESSORIES T o attach a Short Handle (49) to a high pulley , first attach the high pulley to the resistance system (see A TT ACHING THE HIGH PULLEYS AND LEG LEVER on page 13). Then, attach the Short Handle to the Short Cable (33) with a Cable Clip (51).
15 30 31 1 Resistance Bars 6 7 3 43 44 4 “U”-Channel “U”-Channel 80 10 13 W ARNING: Make sure that all of the resistance bars are removed from the “U”- channels before moving the resis tanc e bar assembly to the stored position.
CABLE DIAGRAM The cable diagram shows the proper routing of the Long Cable (80). Use the diagram to make sure that the cable has been assembled correctly . If the cable has not been correctly routed, the resistance system will not function properly and damage may occur .
17 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise.
Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout.
19 MONDA Y D ate: / / EXERCISE RESIST ANCE SETS REPS EXERCISE RESIST ANCE SETS REPS EXERCISE RESIST ANCE SETS REPS AEROBIC EXERCISE AEROBIC EXERCISE TUESDA Y Date: / / WEDNESDA Y Date: / / THURSDA Y Date: / / FRIDA Y Date: / / Make photocopies of this page for scheduling and recording your workouts.
3/8" x 3 3/4" Bolt (90) 3/8" x 2 3/4" Carriage Bolt (83) 3/8" x 4" Bolt (66) 5 #8 x 3/4" T ek Screw (62) # 3/8" x 1 1/2" Button Head Bolt (71) 3/8" x .
5/16" Nylon Jamnut (65) 3/8" Nylon Locknut (76) 1 1/2" Round Inner Cap (38) 2" Square Inner Cap (98) 1 1/2" x 3” Inner Cap (99) #8-32 Nylon Locknut (69) 1 1/4" Round In.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. If a part i s miss ing, call toll-f ree 1- 877-99 2-5999 . See the back cover of the user ’s manual to order replacement parts. Key No. Qty . Description Key No.
84 84 69 79 100 9 3 70 65 59 38 34 10 65 59 38 34 21 71 28 14 8 15 16 21 71 28 54 56 17 17 56 58 58 62 58 53 56 13 9 89 56 56 4 87 87 3 28 76 76 28 28 29 28 29 22 71 24 73 30 103 66 99 5 41 23 2 76 82.
Part No. 221082 R1005A Printed in USA © 2004 Sears, Roebuck and Co. W ARRANTY For one year from the date of purchase, if failure occurs due to defect in material or workmanship in this RESIST ANCE SY.
デバイスWeider 831.15395.0の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Weider 831.15395.0をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider 831.15395.0の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider 831.15395.0の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider 831.15395.0で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider 831.15395.0を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider 831.15395.0の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider 831.15395.0に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider 831.15395.0デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
