Weiderメーカー831.15715.0の使用説明書/サービス説明書
ページ先へ移動 of 20
CAUTION Read all precautions and instruc - tions in this manual before using this equipment. Save this manu- al for future reference. Model No. 831.15715.
2 W ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 I MPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 W ARNING: T o reduce the risk of serious injury , read all important precautions and i nstructions in this manual and all warnings on your weight bench before using your weight bench. Sears assumes no responsibility for personal injury or property damage sustained by or through the use of the weight bench.
4 Seat Curl Pad Leg Lever Curl Bar Safety Spotter W eight Rest Pin Weight T ube Adjustment Knob Backrest Backrest Post BEFORE YOU BEGIN T hank you for selecting the versatile WEIDER ® C ORE 600 weight bench. The weight bench of fers a selection of exercise stations designed to develop the major muscle groups of the body .
5 M6 W asher (32) M10 Nylon Locknut (42) M10 x 165mm Bolt (50) M8 x 70mm Bolt (46) M10 W asher (55) M8 Nylon Locknut (36) M10 x 90mm Carriage Bolt (43) M10 x 90mm Bolt (45) M10 x 85mm Bolt (44) M6 x 8.
6 ASSEMBL Y 1. Orient the Front Stabilizer (2) so that the square holes are toward the floor . Attach the Front Stabilizer to the Front Leg (4) with two M10 x 90mm Carriage Bolts (43) and two M10 Nylon Locknuts (42). Do not tighten the Nylon Locknuts yet.
7 3. Attach the Seat (18) and the Seat Bracket (38) to the Frame (1) with two M6 x 80mm Screws ( 48) and two M6 W ashers (32). 3 4. Attach the Front Leg (4) to the Frame (1) with two M10 x 85mm Bolts (44), two M10 W ashers (55), and an M10 Nylon Locknut (42).
8 6. Apply a portion of the included grease to an M10 x 165mm Bolt (50). Attach the Backrest F rames (16) to the Frame (1) with the Bolt, two M10 W ashers (55), and an M10 Nylon Locknut ( 42). Set the end of the Backrest Post (15) in one of the slots in the Frame.
9 9. Attach the Bumper (39) to the Curl Bar (17) with an M4 x 19mm Screw (54). Attach the Curl Bar (17) to the Leg Lever (5) w ith the Pin/T ether (35). Then, attach the T ether to the Leg Lever with an M4 x 19mm Screw (54). 10. Attach the Curl Pad (20) to the Curl Post (6) with two M6 x 20mm Screws (53).
10 12. Attach a Connector (28) to the Left Upright (1 1) with two M5 x 19mm Screws (52), two M10 x 9 0mm Bolts (45), and two M10 W ashers (55). Do not tighten the Screws yet. Attach the other Connector (28) to the Right Upright (10) in the same way . 13.
1 1 This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 13 for impor- t ant information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for several exercises.
12 ADJUSTING THE WEIGHT RESTS AND THE SAFETY SPOTTERS T o adjust the height of the Weight Rests (12), raise the Weight Rests to the desired height and tighten an Adjustment Knob (37) into each Upright (10, 1 1). Make sure that the Weight Rests are at the same height and that the Adjustment Knobs are fully tightened into the Uprights.
13 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise.
14 Rest for a short period of time after each set. The ideal resting periods follow: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout.
15 MONDA Y D ate: / / EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS AEROBIC EXERCISE AEROBIC EXERCISE TUESDA Y Date: / / WEDNESDA Y Date: / / THURSDA Y Date: / / FRIDA Y Date: / / Make photocopies of this page for scheduling and recording your workouts.
16 MONDA Y D ate: / / EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS AEROBIC EXERCISE AEROBIC EXERCISE TUESDA Y Date: / / WEDNESDA Y Date: / / THURSDA Y Date: / / FRIDA Y Date: / / Make photocopies of this page for scheduling and recording your workouts.
17 Note: Specifications are subject to change without notice. See the back cover of this manual for information about ordering replacement parts. *These parts are not illustrated. If a part is missing, call toll-free 1-877-992- 5999. Key No. Qty . Description Key No.
18 EXPLODED DRA WING—Model No. 831.15715.0 R 0707A 1 4 3 5 15 16 1 6 6 17 24 21 18 19 20 25 25 26 27 27 27 23 23 23 29 30 31 31 33 33 34 34 30 30 35 37 38 39 22 22 22 30 41 36 42 42 42 42 42 42 4 2 .
19 EXPLODED DRA WING—Model No. 831.15715.0 R 0707A 9 11 10 12 12 28 28 7 13 13 40 14 40 14 25 25 25 30 30 30 30 37 37 42 42 42 42 43 43 45 8 42 42 42 45 45 45 52 52 54 54 54 54 55 45 42 9 25 45 55 5.
Part No. 254490 R0707A Printed in China © 2007 ICON IP , Inc. Y our Home For repair— in your home —of all m aj or brand a pplianc es, lawn an d gar den equ ipm ent, or heat ing an d coo ling s ys.
デバイスWeider 831.15715.0の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Weider 831.15715.0をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider 831.15715.0の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider 831.15715.0の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider 831.15715.0で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider 831.15715.0を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider 831.15715.0の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider 831.15715.0に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider 831.15715.0デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
