Weiderメーカー831.159010の使用説明書/サービス説明書
ページ先へ移動 of 27
USER'S MANUAL CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. 831.159010 Serial No. Write the serial number in the space above for reference. Serial Number Decal (under seat) Visit our website at www .
2 WEIDER is a registered trademark of ICON Health & Fitness, Inc. IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . .
3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 74 in. Width: 42 in. Length: 60 in. Foot Plate Low Pulley Station High Pulley Station Front Upright Lat Bar Leg Lever Press Arm/Butterfly Arm W arning Decal 2 (One on each side of the front upright.) Weight Carriage Seat Backrest Thank you for selecting the versatile WEIDER ® 2100 weight system.
5 Before beginning assembly , carefully read the following information and instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
6 4. Press a 50mm Square Inner Cap (22) into the Seat Upright (73). Attach the Bumper (25) to the Seat Upright with an M4 x 20mm Screw (77) and an M5 W asher (75). Attach the Seat Upright (73) to the Front Base (1) with the two indicated M10 x 65mm Carriage Bolts (57) and two M10 Nylon Locknuts (71).
7 6. Press a 50mm Square Inner Cap (22) into the end of the T op Frame (8). Attach the T op Frame (8) to the Front Upright (6) with two M10 x 70mm Bolts (58), the 90mm Space Support Plate (21), and two M10 Nylon Locknuts (71).
8 1 1. Press two 40mm x 50mm Inner Caps (23) into the ends of the Leg Lever (4). Lubricate an M10 x 65mm Bolt (59) with grease. Attach the Leg Lever (4) to the Seat Upright (73) with the Bolt and an M10 Nylon Locknut (71). Do not overtighten the Locknut; the Leg Lever must be able to pivot easily .
9 15. Wrap the Butterfly Cable (46) around a “V”-Pulley (39). Attach the Pulley and a Long Cable T rap (40) to the bracket on the Front Upright (6) with an M10 x 55mm Bolt (69) and an M10 Nylon Locknut (71). Be sure the Cable T rap is turned to hold the Cable in the Groove of the Pulley .
10 18. Wrap the High Cable (45) around a 90mm Pulley (38). Attach the Pulley inside the T op Frame (8) with an M10 x 70mm Bolt (58), two M10 W ashers (26), two 13mm Spacers (34), and an M10 Nylon Locknut (71). 19. Wrap the High Cable (45) around a 90mm Pulley (38).
11 22. Locate the Low Cable (47). Route the Cable through the cage and rest it in the brackets on the Center Base (2). Attach a 90mm Pulley (38) inside the indicated bracket on the Center Base (2) with an M10 x 47mm Bolt (61) and an M10 Nylon Locknut (71).
12 26. Wrap the Low Cable (47) around a 90mm Pulley (38). Attach the Pulley to the Double “U”-Bracket (37) with an M10 x 47mm Bolt (61) and an M10 Nylon Locknut (71).
13 30. Attach the Backrest (15) to the Front Upright (6) with two M6 x 65mm Bolts (65), and two M6 W ashers (35). 31. Press two 19mm Round Inner Caps (27) into the ends of a Pad T ube (17). Slide the Pad T ube through the hole in the Leg Lever (4). Slide two Foam Pads (18) onto the ends of the Pad T ube.
14 33. Make sure that all parts have been properly tightened. The use of all remaining parts will be explained in ADJUSTMENTS, below . Before using the weight system, pull each cable a few times to make sure that the cables move smoothly over the pulleys.
15 14 20 Weight T ube Weight Weight Stop ADDING WEIGHTS TO THE WEIGHT CARRIAGE T o add resistance to the weight system, slide an equal amount of weight (not included) onto each side of the weight tube on the Weight Carriage (14). Be sure that the weights are pushed against the weight stops.
WEIGHT (lbs.) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 11 0 11 5 120 125 130 135 140 145 150 PRESS ARM (lbs.) 12 16 20 24 28 32 36 39 43 46 50 53 57 60 64 67 71 74 78 81 85 88 92 95 99 102 105 108 111 11 4 11 7 BUTTERFL Y ARM (lbs.
High Cable (45) CABLE DIAGRAMS The cable diagrams below show the proper routing of the Butterfly Cable (46), the High Cable (45), and the Low Cable (47). Use the diagrams to make sure that the cables and the cable traps have been assembled correctly .
18 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise.
19 Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout.
Part No. 188926 R1002A Printed in China © 2002 Sears, Roebuck and Co. Model No. 831.159010 QUESTIONS? If you find that: • you need help assembling or operating the WEIDER ® 2100 weight system • .
This chart is provided to help you identify the small parts used in assembly . The number in parenthesis below each part refers to the key number of the part from the P ART LIST in the center of this manual. Important: Some parts may have been pre-assembled for shipping.
.
M6 W asher (35) M10 Nylon Locknut (71) M8 Nylon Locknut (70) M8 x 70mm Bolt (72) M5 W asher (75) M4 x 10mm Screw (68) M6 x 65mm Bolt (65) M6 x 15mm Bolt (66) M10 x 82mm Bolt (50) M10 x 65mm Carriage B.
25mm Round Inner Cap (33) 19mm Round Inner Cap (27) 50mm Square Inner Cap (22) 40mm x 50mm Inner Cap (23) 50mm x 75mm Inner Cap (29) 38mm Square Inner Cap (41) 31mm Round Inner Cap (24) "V"-Pulley (39) (Not shown to scale) 90mm Pulley (38) (Not shown to scale) P ART IDENTIFICA TION CHART—Model No.
81 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL. SA VE THIS P ART LIST/EXPLODED DRA WING FOR FUTURE REFERENCE.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. P ART LIST—Model No. 831.159010 R1002A 1 1 Front Base 2 1 Center Base 3 1 Rear Base 4 1 Leg Lever.
71 45 1 2 3 7 4 5 6 8 10 11 12 13 14 15 16 17 17 18 18 18 18 19 19 20 20 21 22 23 24 24 23 23 22 27 27 27 27 28 28 28 22 30 30 30 31 32 32 33 33 34 34 34 34 34 34 34 34 34 34 36 36 37 38 38 38 38 38 3.
デバイスWeider 831.159010の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Weider 831.159010をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider 831.159010の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider 831.159010の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider 831.159010で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider 831.159010を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider 831.159010の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider 831.159010に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider 831.159010デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
