Weiderメーカー831.159360の使用説明書/サービス説明書
ページ先へ移動 of 29
P A TENT PENDING TM Model No. 831.159360 Serial No. The serial number can be found in the location shown belo w . Write the ser ial number in the space abov e. CA UTION Read all precautions and instruc- tions in this manual bef ore using this equipment.
2 T ABLE OF CONTENTS IMPOR T ANT PRECA UTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 BEFORE Y OU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 BEFORE Y OU BEGIN ASSEMBLED DIMENSIONS: Height: 76 in. Width: 38 in. Length: 59 in. Low Pulle y Station F oot Plate High Pulley Station Lat Bar Leg Le ver Butterfly Arms Press Ar m Squat Ar m W eight Stack Seats Backrests Thank you f or selecting the WEIDER ® PRO 9625 Home Gym System.
4 ASSEMBL Y 1 2 27 11 11 1 5 78 78 3 5 51 51 11 4 1 Before beginning assemb ly , carefully read the follo wing information and instructions: • Place all par ts of the home gym system in a cleared area and remov e the packing materials; do not dispose of the packing materials until assembly is completed.
5 3. Press a 2” Square Inner Cap (27) into the Rear Upright (56). Attach a Rubber Bumper (90) to the Rear Upright (56) with a #8 x 1/2” T ap Screw (89). Slide the Rear Upright (56) onto the 5/16” x 2 1/2” Carriage Bolts (1) in the Rear Base (51).
6 5. Set two Weight Bumpers (19) onto the br ack et on the Stabilizer (5). Insert both W eight Guides through the Weight Bumpers and the brac ket on the Stabilizer . Be sure that the drilled holes in the Weight Guides are at the top, as shown. Press a 1” Round Cover Cap (70) onto the bottom of each Weight Guide (62).
7 8. Attach the upper ends of the Weight Guides (62) to the T op F rame (55) with the 5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and a 5/16” Nylon Lockn ut (3). Tighten all Nylon Lockn uts used in steps 2 through 8. 9. Press a 1” x 7/8” Plastic Bushing (75) onto each welded spacer on the Press F rame (17).
8 12. Lubricate both axles on the T op F rame (55). Slide the Right Arm (48) onto the r ight axle. Note: Be careful not to confuse the Right Arm with the Left Arm (47); refer to step 11 to identify the Right Arm. Be sure that the upper end of the Right Arm is behind the indicated bracket on the T op Frame (55).
9 14. During steps 15 through 36, refer to the CABLE DIA GRAM on page 23 of this manual to verify proper cab le routing. Bef ore begin- ning this section, identify the Long Cable (86), the Medium Cable (23), and the Short Cable (58) by comparing the lengths and ends of the cables .
10 18. Route the Medium Cable (23) around the “V”- Pulley (6) on the Right Arm (48). Be sure that the Cable is in the gr oove of the “V”- Pulley and that the Long Cable T rap (50) is turned to hold the Cable in place. Tighten the 3/8” x 2 1/2” Bolt (7) and the 3/8” Nylon Lockn ut (not shown).
11 21. Wrap the Medium Cab le (23) around a 3 1/2” Pulley (15). Attach the Pulle y to the T op F rame (55) with a 3/8” x 1 3/4” Bolt (87) and a 3/8” Nylon Lockn ut (21).
25. Attach the end of the Shor t Cable (58) to the Long “U”-Bracket (57) with a 1/4” Nylon Lock- nut (2) and a 1/4” Flat W asher (10). Do not completely tighten the Nylon Loc knut. It should be threaded onto the end of the Cable so onl y a couple of threads are showing abo ve the nut, as shown in the inset drawing.
13 27. Locate the Long Cable (86). Route the Long Cable under the 3 1/2” Low Pulley (88). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame (17) and that the Cable is between the Pulley and the cr ossbar on the Press Frame.
14 31. Wrap the Long Cab le (86) around a 3 1/2” Pulley (15). Attach the Pulle y and a Cable T rap (66) to the Press F rame (17) with a 3/8” x 3 1/2” Bolt (16), a 3/8” Flat Washer (9), and a 3/8” Nylon Lockn ut (21).
15 35. Route the Long Cable (86) around the indicat- ed 3 1/2” Pulley (15) and through the Long “U”-Brac ket (57). The Cable must be between the Cable T rap (66) and the Pulley . Tighten 3/8” x 2” Bolt (12) and the 3/8” Nylon Lockn ut (not shown).
16 38. Press a 1 3/4” Square Inner Cap (44) into the Rear Seat F rame (77). Inser t the 1/4” x 2 1/2” Carr iage Bolt (91) into the center hole in a Seat Plate (37). Attach the Seat Plate to a Seat (13) with two 1/4” x 1/2” Screws (18). Inser t the 1/4” x 2 1/2” Carr iage Bolt (91) into the indicated hole in the Rear Seat F rame (77).
17 41. Press a 1 1/2” Square Inner Cap (32) into the F ront Seat F rame (36). Inser t the 1/4” x 2 1/4” Carr iage Bolt (38) into the center hole in a Seat Plate (37).
18 44. Press 3/4” Round Inner Caps (34) into the ends of both P ad T ubes (28). Inser t one P ad T ube (28) into the F ront Seat F rame (36). Slide a Foam P ad (30) onto each end of the P ad T ube. Inser t the other P ad T ube (28) into the Leg Le ver (29).
19 ADJUSTMENT The instructions below describe how each par t of the home gym system can be adjusted. Refer to the e xercise poster accompanying this manual to see ho w the home gym system should be set up for each e xercise .
20 A TT ACHING THE LEG LEVER T O THE LO W PUL- LEY ST A TION T o use the Leg Lev er (29), the seat must be attached to the front upright (see A TT ACHING AND REMO V- ING THE SEA TS below). Attach one end of the Chain (52) to the Long Cable (86) with a Cable Clip (53).
21 WEIGHT RESIST ANCE CHART This char t shows the appro ximate weight resistance at each station. “T op” ref ers to the 6.5 lb. top weight. The other numbers ref er to the 12.5 lb . weight plates. Weight resistance sho wn for the b utterfly ar m station is for each butterfly arm.
22 TR OUBLE-SHOO TING AND MAINTENANCE Inspect and tighten all par ts each time you use the home gym system. Replace any worn par ts immediately . The home gym system can be cleaned using a damp cloth and mild non-abrasiv e detergent. Do not use solv ents.
23 4 3 2 7 7 8 8 6 2 5 4 3 2 Base— 10 6 1 —Low Pulle y 1 —High Pulley Long Cable (86) Medium Cable (23) Rear Upright— 1 9 —W eight Stack 9 Short Cable (58) 5 CABLE DIA GRAM The cable diag ram below shows the proper routing of the Short Cable (58), the Medium Cable (23), and the Long Cable (86).
1" Round Inner Cap (49)–6 1" Round Cover Cap (70)–4 3/4" Round Inner Cap (34)–4 5/16" x 2" Eyebolt (35)—1 1 1/2" Square Inner Cap (32)—2 1 3/4" Square Inne.
1/4" Flat W asher (10)–10 5/16" Flat W asher (8)–1 1 3/8" Flat W asher (9)–7 1/4" x 2 1/2" Screw (43)–4 3/8" Nylon Locknut (21)–20 1/4" Nylon Lock nut (2).
1" Retainer (69)–4 5/16" x 1 3/4" Bolt (72)–1 1/2" x 3/4" Spacer (61)–2 3/8" x 2" Bolt (12)–3 3/8" x 3 1/2" Bolt (16)–2 5/16" x 2 1/2" .
Note: “#” indicates a non-illustrated par t. Specifications are subject to change without notice. P AR T LIST—Model No. 831.159360 R0896A Key Par t No.
21 9 15 71 85 21 12 20 15 66 21 15 21 87 80 58 93 27 10 43 23 72 3 10 2 12 81 81 15 15 21 10 43 41 3 21 6 50 7 58 10 2 78 78 19 11 11 1 27 51 5 11 12 15 66 1 27 3 3 21 66 12 57 21 71 66 15 3 9 3 6 21 .
P ar t No . 132823 R0896A Printed in Canada © 1996 Sears, Roebuc k and Co . Model No. 831.159360 QUESTIONS? If you find that: • y ou need help assembling or operating the WEIDER ® PRO 9625 • a p.
デバイスWeider 831.159360の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Weider 831.159360をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider 831.159360の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider 831.159360の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider 831.159360で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider 831.159360を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider 831.159360の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider 831.159360に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider 831.159360デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
