Weiderメーカー831.159530の使用説明書/サービス説明書
ページ先へ移動 of 35
USER’S MANUAL Model No. 831.159530 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference.
2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3. The weight system is intended for home use only .
4 ASSEMBLED DIMENSIONS: Height: 77 in. Width: 103 in. Depth: 55 in. Low Pulley Station Foot Plate Leg Lever Press Arms Decal 1 Decal 1 Decal 2 Backrest Curl Pad Butterfly Arms Ab Pulley Station Leg Press Arm Thank you for selecting the innovative and versatile WEIDER ® PRO 9950 weight system.
5 Make sure you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
1. Before beginning, make sure that you have read and understood the information on page 5. Locate and open the parts bags labeled “FRAME ASSEMBL Y 1 and 2.” Press a 2” Square Inner Cap (59) into each end of the Butterfly Base (1). Insert four 5/16” x 2 1/2” Carriage Bolts (54) up through the Butterfly Base (1).
4. Press a 1 1/2” Square Inner Cap (100) into the indicated part of the Press Upright (6). Orient the Press Upright (6) as shown. Attach the Press Upright to the indicated 5/16” x 2 1/2” Carriage Bolts (54) in the Press Base (3) with two 5/16” Nylon Locknuts (64).
8. Attach the T op Frame (5) to the Butterfly Upright (4) with two 3/8” x 2 3/4” Bolts (58), a Short Support Plate (26), and two 3/8” Nylon Locknuts (74). Note: Be sure that the T op Frame is ori- ented with the long bracket on the side shown, and that it rests between the Weight Guides (33) as shown in step 9.
9 12 13 14 55 55 66 66 9 Adjustment knob must be on this side 64 10 54 64 12 59 71 72 3 64 64 66 55 6 10 66 66 64 1 1. Press a 2” Square Inner Cap (59) into the Press T op Frame (13). Attach the Press T op Frame (13) to the Press Upright (6) with two 5/16” x 2 3/4” Bolts (55), a Long Support Plate (34), and two 5/16” Nylon Locknuts (64).
85 86 Axle 10 15. Locate and open the parts bag labeled “ARM ASSEMBL Y .” Press a 2” Square Inner Cap (59) into each end of the Leg Lever (8). Lubricate the 3/8” x 3 1/4” Bolt (101). Attach the Leg Lever (8) to the Butterfly Front Leg (9) with the Bolt and a 3/8” Nylon Jamnut (88).
18 18. Press two 1 3/4” Square Inner Caps (60) into the top of the Press Frame (14). Lubricate the 3/8” x 9” Bolt (92). Attach the Press Frame (14) to the Press T op Frame (13) with the Bolt, four 3/8” SAE W ashers (102), and a 3/8” Nylon Locknut (74).
21 12 24. Wrap the Press Cable (80) around a 3 1/2” Pulley (37). Attach the Pulley to the indicated side of the Press Frame (14) with a 3/8” x 3 1/2” Bolt (65), a 3/8” W asher (75), and a 3/8” Nylon Locknut (74). 24 22. Locate and open the parts bag labeled “CABLE ASSEMBL Y .
13 27. Wrap the Press Cable (80) around a 3 1/2” Pulley (37). Attach the Pulley and a Cable T rap (44) to the Press Upright (6) with a 3/8” x 3 3/4” Bolt (62), a 3/8” W asher (75), and a 3/8” Nylon Locknut (74). Make sure the Cable T rap is turned to hold the Cable in the groove of the Pulley .
14 30. Wrap the Press Cable (80) around a “V”-Pulley (38). Attach the Pulley and a Long Cable T rap (50) to the indicated hole in the Press Seat Frame (12), using a 3/8” x 4 1/4” Bolt (104), a 3/8” W asher (75) and a 3/8” Nylon Locknut (74).
15 34. Wrap the Press Cable (80) around a 3 1/2” Pulley (37). Attach the Pulley to the bracket on the T op Frame (5) with a 3/8” x 2” Bolt (79) and a 3/8” Nylon Locknut (74).
16 37. Wrap the Butterfly Cable (81) around a “V”-Pulley (38). Attach the Pulley and a Long Cable T rap (50) to the indicated side of the bracket on the Butterfly Upright (4) with a 3/8” x 2 1/2” Bolt (78) and a 3/8” Nylon Locknut (74). Be sure the Long Cable T rap is turned to hold the Cable in the groove of the Pulley .
17 41 37 74 49 49 83 Rod Ball Large tabs must be on this side 4 75 75 41. Identify the Ab Cable (83); it is approximately 220.25” long and it has a ball on one end and a loop on the other . Wrap the Ab Cable (83) around a 3 1/2” Pulley (37). Place two Pulley Covers (49) over the Pulley; make sure that the large tabs are in the position shown.
18 45. Wrap the Ab Cable (83) around a 3 1/2” Pulley (37). Attach the Pulley to the bracket on the Butterfly T op Frame (19) with a 3/8” x 2” Bolt (79) and a 3/8” Nylon Locknut (74). 45 37 19 83 Bracket 74 79 46. W rap the Ab Cable (83) around a 3 1/2” Pulley (37).
49 50 19 49. Wrap the Leg Press Cable (82) around a 3 1/2” Pulley (37). Attach the Pulley and a Cable T rap (44) to the Butterfly Upright (4) with a 3/8” x 5” Bolt (61) and a 3/8” Nylon Locknut (74). Do not tighten the Nylon Locknut yet. Be sure that the Cable T rap is turned to hold the Cable in the groove of the Pulley .
20 53. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Press a 1 1/2” Square Inner Cap (100) into the bottom of a Seat Bracket (1 1). Press two 1” x 2” Inner Caps (70) into the ends of the Seat Bracket. Insert a 1/4” x 1 3/4” Carriage Bolt (93) into the center hole of a Support Plate (57).
21 56 106 57 90 90 84 51 6 70 21 84 98 100 93 20 57. Press a 1 3/4” Square Inner Cap (60) into the back of the Adjustment T ube (23). Attach the Adjustment T ube (23) to the Press Plate (24) with a 5/16” x 2 1/2” Bolt (63), two 5/16” W ashers (66), and a 5/16” Nylon Locknut (64).
59 22 59. Attach the Curl Pad (36) to the Curl Post (35) with two 1/4” x 3/4” Bolts (90). 35 90 90 36 60. Make sure that all parts have been properly tightened before using the weight system. The use of the remaining parts will be explained in ADJUSTMENTS, beginning on page 23 of this manual.
ADJUSTING THE SEA T T o adjust the height of the Seat (25) on the Press Seat Frame (12), loosen the Adjustment Knob (51) by turning it counterclockwise, and pull it out as far as possible. Move the Seat to the desired height and snap the Knob into an adjustment hole in the Seat Bracket (1 1).
24 36 35 59 9 45 47 47 68 48 27 31 Weight T ube 28 52 A TT ACHING THE CURL P AD T o use the Curl Pad (36), remove the 2” Square Inner Cap (59) and insert the Curl Post (35) into the Butterfly Front Leg (9). Secure the Curl Post with the Curl Adjustment Knob (52).
25 Weight High Arm Leg Butterfly Leg Lever Low Arm (lbs.) Pulley Press Press Arm (lbs.) Pulley (lbs.) (lbs.) (lbs.) (lbs.)* (lbs.) 20 30 23 44 9 26 22 40 60 45 88 18 52 45 60 90 68 132 27 78 67 80 120.
26 The cable diagrams below show the proper routing of the Butterfly Cable (81), the Ab Cable (83), the Leg Lever Cable (82) and the Press Cable (80). The numbers show the correct route for each Cable. Make sure that the Cables are routed correctly , that the pulleys move smoothly , and that the cable traps do not touch or bind the Cables.
27 Slack can be removed form the Press Cable (80) by moving the indicated “V”-Pulley (38) to one of the four free holes in the Press Seat Frame (12). Remove the 3/8” x 4 1/4” Bolt (104), 3/8” W asher (75), and 3/8” Nylon Locknut (74) from the Press Seat Frame, Pulley , and Long Cable T rap (50).
Part No. 177796 R1001A Printed in Canada © 2001 Sears, Roebuck and Co. SEARS, ROEBUCK AND CO., HOFFMAN EST A TES, IL 60179 Model No. 831.159530 QUESTIONS? If you find that: • you need help assembli.
Note: Assembly is divided into four stages: 1) frame assembly; 2) arm assembly; 3) cable assembly; and 4) seat assembly . The hardware for each assembly stage is packaged separately .
1” Retainer (85) 1" CoverCap (86) 1 3/4" Square Inner Cap (60) 1" Inner Cap (32) 1" x 2” Inner Cap (70) 1 1/2" Round Inner Cap (67) 3/4" Round Inner Cap (73) 2" .
3/8" Nylon Locknut (74) 3/8" Nylon Jamnut (88) 5/16" Nylon Jamnut (105) 1/2" Nylon Locknut (95) 1/4" x 1 3/4" Screw (98) 5/16" Nylon Locknut (64) 3/8" x 2".
3/8" x 3 1/2" Bolt (65) 3/8" W asher (75) 3/8" x 3 3/4" Bolt (62) 3/8 " x 9 " Bolt (92) 5/16" W asher (66) 5/16" x 2 3/4" Bolt (55) 3/8" x 3 1/4&.
81 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL.
Key No. Qty . Description Key No. Qty . Description 1 1 Butterfly Base 2 1 Center Base 3 1 Press Base 4 1 Butterfly Upright 5 1 T op Frame 6 1 Press Upright 7 1 Support Brace 8 1 Leg Lever 9 1 Butterf.
45 48 47 24 64 46 23 60 66 63 22 74 37 44 44 37 61 96 69 95 89 89 74 74 64 2 29 29 74 32 32 32 32 31 30 30 31 30 30 27 27 27 27 30 30 31 78 78 78 78 28 28 29 29 80 83 33 33 64 74 74 74 20 53 37 91 55 .
デバイスWeider 831.159530の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Weider 831.159530をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider 831.159530の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider 831.159530の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider 831.159530で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider 831.159530を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider 831.159530の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider 831.159530に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider 831.159530デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
