WeiderメーカーPRO XT75の使用説明書/サービス説明書
ページ先へ移動 of 18
Model No. 831.153220 Serial No. Write the serial number in the space above for reference. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Serial Number Decal USER’S MANUAL Visit our website at www .
W ARNING DECAL PLACEMENT 2 W ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual before using the weight rack. Use the weight rack only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight rack are ade- quately informed of all precautions.
4 Weight Carriage High Pulley Station Lat Bar Weight Rest Weight Spotter Right Side Left Side Note: The terms “right side” and “left side” are determined relative to a person standing with his or her back to the rack; they do not correspond to right and left on the drawings in the manual.
5 M10 Nylon Locknut (31) M8 Nylon Locknut (32) M10 x 66mm Bolt (37) 51mm Spacer (43) 24mm Spacer (42) M10 x 45mm Bolt (34) 18mm Spacer (45) 28mm Spacer (44) M8 Flat W asher (40) M10 Flat W asher (41) .
1. Press four 60mm Square Outer Caps (28) onto the ends of the Right and Left Bases (1, 3). Attach the Right and Left Bases (1, 3) to the Center Base (2) using four M10 x 78mm Bolts (33) and four M10 Nylon Locknuts (31). Do not tighten the Nylon Locknuts yet.
7 4 5a 5b 5. Refer to drawing 5a. Press six Square Bushings (21) into the Right Weight Rest (19) and the Right Weight Spotter (20) as shown. Pull out the Adjustment Knobs (22) and slide the Right Weight Spotter and the Right Weight Rest down over the right Uprights (7, 8) as indicated.
8 6. Attach the Chin-up Bar (13) and two Joint Plates (6) to the Front Uprights (7) using four M10 x 78mm Bolts (33) and four M10 Nylon Locknuts (31). Do not tighten the Nylon Locknuts yet. 9. Set the two Weight Bumpers (18) over the indicated holes in the Weight Guide Base (4).
9 10 10. Press a 60mm Square Inner Cap (29) into the end of the Weight Guide Frame (14). Hold the Weight Guide Frame (14) on top of the Center Frame (1 1) and the Weight Guides (9). Attach the Weight Guides to the W eight Guide Frame using two M8 x 72mm Bolts (35), four M8 Flat W ashers (40), and two M8 Nylon Locknuts (32).
10 14 26 14 36 31 41 45 25 25 2 31 16 31 17 17 34 25 24 26 27 24 14. Lift the High Cable (26) in the location shown. Attach two Pulleys (25) inside the Weight Guide Frame (14) using two M10 x 75mm Bolts (36), four M10 Flat W ashers (41), four 18mm Spacers (45), and two M10 Nylon Locknuts (31).
11 17 38 30 30 17. Wet the ends of the Lat Bar (38) with a small amount of soapy water . Slide the Handgrips (30) onto the ends of the Lat Bar . 18. Make sure all parts of the weight rack are properly tightened. In addition, pull each cable a few times to make sure the cables move smoothly over the pulleys.
12 USING THE WEIGHT RESTS AND WEIGHT SPOTTERS Before beginning an exercise, move the Weight Rests (19, 48) and the Weight Spotters (20, 49) to sets of holes in the uprights that are best suited for that exer- cise. The selected holes for the W eight Spotters should represent the lowest point to which you want the barbell to go during the exercise.
13 A TT ACHING WEIGHTS TO THE WEIGHT CARRIAGE T o use the high or low pulley station, slide the desired amount of weight onto the weight tubes of the Weight Carriage (15) and secure the weights with Weight Clips (50). 50 15 Weight Tu b e Weight T ube W ARNING: Do not place more than 150 pounds on the Weight Carriage (15).
14 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise.
15 Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user ’s manual for information about ordering replacement parts.
EXPLODED DRA WING—Model No. WEBE24410 23 38 39 30 30 31 33 6 13 29 33 31 41 31 11 10 12 33 6 33 31 33 31 29 31 34 17 17 25 24 25 24 29 14 25 25 47 41 45 31 31 41 45 26 34 31 6 27 7 8 33 31 31 31 1 2.
FULL 90-DA Y W ARRANTY Part No. 177090 R0701A Printed in China © 2001 ICON Health & Fitness, Inc. ORDERING REPLACEMENT P ARTS For 90 days from the date of purchase, if failure occurs due to defec.
デバイスWeider PRO XT75の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Weider PRO XT75をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider PRO XT75の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider PRO XT75の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider PRO XT75で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider PRO XT75を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider PRO XT75の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider PRO XT75に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider PRO XT75デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
