WeiderメーカーWEBE27331の使用説明書/サービス説明書
ページ先へ移動 of 24
Visit our website at www .weiderfitness.com new products, prizes, fitness tips, and much more! CAUTION Read all precautions and instruc - tions in this manual before using this equipment. Save this manual for future reference. Model No. WEBE27331 Serial No.
2 W ARNING DECAL PLACEMENT W ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPOR T ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Read all instructions in this manual before using the weight bench. Use the weight bench only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight bench are ade- quately informed of all precautions.
ASSEMBLED DIMENSIONS: Height: 84 in. Width: 67 in. Depth: 75 in. 4 Weight Carriage Front Upright Safety Spotter Weight Rest Storage T ube Backrest Bracket Right Side Left Side Note: The terms “right.
5 Before beginning assembly , carefully read the following information and instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
6 5. Attach the Backrest (10) to the Backrest Frames (6) with four M6 x 53mm Screws (29) and four M6 W ashers (37). Note: If the four Screws cannot be inserted into the Backrest properly , go back to step 4 and readjust the Backrest Frames. 4. Press four 20mm x 40mm Inner Caps (20) into the ends of the two Backrest Frames (6).
31 37 32 29 30 15 7 6. Press four Bushings (34) into the Backrest Frames (6) as shown. Secure the Backrest Knob (25) to the Bench Frame (2). Pull the Knob out as far as it will go. Slide the Backrest Bracket (9) between the Bench Frame tubes and engage the Knob into a hole in the Bracket.
8 9. Press three 50mm Square Inner Caps (22) into the Leg Lever (7). Press a 48mm Round Inner Cap (23) into the tube on the Leg Lever . Slide the two Pad T ubes (16) into the Leg Lever (7). Slide four Foam Pads (17) onto the ends of the Pad T ubes. Press four 19mm Round Inner Caps (19) into the ends of the Pad T ubes.
9 12. Attach the left side of the Front Crossbar (43) to the Base (42) with two M10 x 94mm Bolts (18), a Large Joint Plate (41), and two M10 Nylon Locknuts (32).
10 15. Attach the Rear Crossbar (45) to the Left Rear Upright (46) with two M10 x 94mm Bolts (18), two M10 W ashers (74), and two M10 Nylon Locknuts (32). Do not tighten the Locknuts yet. Attach the Rear Crossbar (45) to the Right Rear Upright (not shown) in the same manner .
1 1 17. Press a 51mm x 76mm Inner Cap (21) into the top of a Front Upright (44). Attach an Upright Cover (51) to the Front Upright with five M4 x 16mm Screws (63). Attach the Front Upright (44) to a Base (42) with four M10 x 94mm Bolts (18), two Small Joint Plates (40), and four M10 Nylon Locknuts (32).
12 20. Route the Cable (79) up through the Lat T ower (48) and over an 89mm Pulley (65). Attach the Pulley inside of the Lat T ower with an M10 x 75mm Bolt (30), two M10 W ashers (74), two Long Spacers (67), and an M10 Nylon Locknut (32). Make sure the large ball on the Cable is in the indicated position.
13 24. Route the Cable (79) through the Lat T ower Base (49) and under an 89mm Pulley (65). Attach the Pulley to the bracket on the Lat T ower Base with an M10 x 45mm Bolt (27) and an M10 Nylon Locknut (32). 26. Press two 48mm Round Inner Caps (23) into two Storage T ubes (70).
14 28. W et the ends of the Lat Bar (59) with soapy water . Slide two Handgrips (60) onto the ends of the Lat Bar . 29. Make sure that all parts are properly tightened before you use the weight bench. The use of all remaining parts will be explained in ADJUSTMENTS starting on the next page.
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 17 for impor- tant information about how to get the most benefit from your exercise program. Also, see the accompanying exercise guide to see the correct form for each exercise.
16 81 44 79 66 59 WEIGHT RESTS AND SAFETY SPOTTERS T o use the barbell (not shown) with the weight rack, first move the Weight Rests (55 [not shown], 80) and the Safety Spotters (56 [not shown], 81) to the correct heights for the exercise to be performed.
17 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS MUSCLE BUILDING T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise.
18 Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout.
19 MONDA Y Date: / / EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS AEROBIC EXERCISE AEROBIC EXERCISE TUESDA Y Date: / / WEDNESDA Y Date: / / THURSDA Y Date: / / FRIDA Y Date: / / Make photocopies of this page for scheduling and recording your workouts.
M10 x 68mm Bolt (26) M10 x 45mm Bolt (27) M10 x 100mm Bolt (28) M10 x 75mm Bolt (30) M10 x 86mm Bolt (35) M10 x 19mm Bolt (72) M10 x 78mm Bolt (75) M6 x 16mm Screw (31) M4 x 16mm Screw (63) M6 W asher.
19mm Round Inner Cap (19) 50mm Square Inner Cap (22) 45mm Square Inner Cap (76) 38mm x 50mm Inner Cap (77) 20mm x 40mm Inner Cap (20) 51mm x 76mm Inner Cap (21) 60mm Square Inner Cap (62) 32mm Round I.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of this manual for information about ordering replacement parts.
81 68 80 68 66 71 1 2 3 4 5 6 6 12 7 8 9 10 1 1 13 15 14 14 16 16 17 17 17 17 22 22 22 23 19 19 78 78 39 39 22 22 22 22 21 33 18 26 28 30 29 31 36 29 29 73 73 31 75 34 34 34 34 34 61 61 37 37 37 37 37.
Part No. 210821 R0204A Printed in China © 2004 ICON Health & Fitness, Inc. LIMITED W ARRANTY ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate- rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase.
デバイスWeider WEBE27331の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Weider WEBE27331をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider WEBE27331の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider WEBE27331の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider WEBE27331で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider WEBE27331を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider WEBE27331の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider WEBE27331に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider WEBE27331デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。