WeiderメーカーWEBE29911の使用説明書/サービス説明書
ページ先へ移動 of 26
USER’S MANUAL Visit our website at www .weiderfitness.com new products, prizes, fitness tips, and much more! CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No.
2 W ARNING DECAL PLACEMENT W ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual before using the weight bench. Use the weight bench only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight bench are ade- quately informed of all precautions.
4 W eight Carriage Pulley Arm Pulley Arm Safety Spotter W eight Rest W eight Rest Power Assist Leg Bench Cable Bracket Right Side Left Side Note: The terms “right side” and “left side” are determined relative to a person sitting on the bench; they do not correspond to right and left on the drawings in the manual.
5 M10 x 75mm Bolt (73) M10 x 78mm Bolt (70) M10 x 100mm Bolt (66) M10 x 45mm Bolt (76) M10 x 86mm Bolt (63) M10 x 97mm Bolt (90) M10 x 81mm Bolt (65) M10 x 91mm Bolt (67) M10 x 120mm Bolt (75) M10 x 6.
6 Before beginning assembly , carefully read the following information and instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
5. Press two 75mm Bushings (26) into the top and bottom of the Safety Spotter (10). Attach the two Safety Spotter Bumpers (34) to the Safety Spotter (10) with two M10 x 25mm Button Bolts (81), two M10 W ashers (79), and two M10 Nylon Locknuts (77). Pull the Knob (30) out as far as it will go.
8 6. Press two 75mm Bushings (26) into the top and bottom of the Right Weight Rest (12). Pull the Knob (30) out as far as it will go. Slide the Right Weight Rest (12) onto the Right Upright (2) and engage the Knob into an adjustment hole in the Upright.
9 11 12 13 13. Press a 38mm x 50mm Inner Cap (64) into the indicated part of the Sliding Seat Frame (15). Press two 75mm Bushings (26) into the ends of the Sliding Seat Frame. Orient the Sliding Seat Frame (15) as shown. Pull the Knob (not shown) out as far as it will go.
10 14. Attach the Bench Frame (14) to the Back Leg (39) with an M10 x 78mm Bolt (70), two M10 x 164mm Bolts (71), an M10 W asher (79), and three M10 Nylon Locknuts (77). Do not tighten the Nylon Locknuts yet. 17. Press two 38mm Square Inner Caps (44) into the ends of the Support Leg (13).
11 18 18. Press two 38mm Square Inner Caps (44) into the ends of the Seat Frame (17). Orient the Seat (37) with the wide end on the side shown. Attach the Seat (37) to the Seat Frame (17) with four M6 x 16mm Bolts (72). 37 Wide End 72 72 17 44 44 19 19.
25 12 22 18 96 96 35 58 76 22. Route the Bench Cable (58) under a 4 1/2” Pulley (35). Attach the Pulley to the Front Leg (18) with an M10 x 75mm Bolt (73), two 17mm Spacers (96), two M10 W ashers (79), and an M10 Nylon Locknut (77). 23. Attach the Bench Cable (58) to the Back Leg (39) with a Cable Clip (28).
13 27 28 29 30 35 36 55 76 5 7 35 76 93 33 77 77 77 76 61 T ube 27. W rap the High Cable (61) around a 4 1/2” Pulley (35). Attach the Pulley and a Large Cable T rap (55) to the “U”-Bracket (33) with an M10 x 45mm Bolt (76) and an M10 Nylon Locknut (77).
32. W rap the Carriage Cable (60) around an 88mm Pulley (36). Attach the Pulley inside the T op Frame (9) with an M10 x 75mm Bolt (73), two 17mm Spacers (96), two M10 W ashers (79), and an M10 Nylon Locknut (77). 32 33. W rap the Carriage Cable (60) around an 88mm Pulley (36).
36. Route the Low Cable (59) through the Center Upright (3) and under the bar in the bracket on the Center Base (24). Wrap the Cable around an 88mm Pulley (36). Attach the Pulley to the rear hole in the bracket on the Center Base with an M10 x 45mm Bolt (76) and an M10 Nylon Locknut (77).
39. Attach the Low Cable (59) to the “U”-Bracket (33) with an M6 W ashers (62) and an M6 Locknut (80). Do not completely tighten the Locknut; it should be threaded onto the end of the Cable until only two threads are showing above the Locknut, as shown in the inset drawing.
This section explains how to adjust the weight bench. The first time you perform an exercise that uses the safety spotter , adjust the bench to the position that is best for you. Note the position of the weight rest and safety spot- ter on the BENCH ADJUSTMENT CHAR T , on page 20 of this manual.
18 28 59 58 25 98 W eight T ube W eight Barbell AT T ACHING THE BENCH TO THE RACK To perform bench and leg lever exercises, the weight bench must be attached to the weight rack. T o attach the bench to the rack, rest the Back Leg (39) over the crossbar on the Center Base (24).
19 AT T ACHING THE ACCESSORIES TO THE CABLES To use the Row Bar (38), attach it to the High Cable (61) or Low Cable (not shown) with a Cable Clip (28).
Bench Bench Cable W eight Rest Safety Spotter Exercises Follow these steps when preparing for each exercise: 1. Adjust the position of the bench (be sure the bench cable is attached to the low cable when performing any of the bench exercises) 2. Adjust the position of the weight rests 3.
21 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS MUSCLE BUILDING To increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise.
22 Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout.
23 MONDA Y Date: / / EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS EXERCISE WEIGHT SETS REPS AEROBIC EXERCISE AEROBIC EXERCISE TUESDA Y Date: / / WEDNESDA Y Date: / / THURSDA Y Date: / / FRIDA Y Date: / / Make photocopies of this page for scheduling and recording your workouts.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user ’s manual for information about ordering replacement parts.
35 55 31 55 35 1 2 4 5 8 7 7 6 11 12 13 14 15 16 17 18 19 20 21 22 23 24 26 26 26 26 30 30 30 26 26 36 36 35 36 35 35 37 38 39 40 41 41 41 42 42 42 42 42 44 44 44 44 45 45 64 46 48 48 48 48 48 48 49 5.
Part No. 203937 R0803A Printed in China © 2003 ICON Health & Fitness, Inc. LIMITED W ARRANTY ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate- rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase.
デバイスWeider WEBE29911の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Weider WEBE29911をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider WEBE29911の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider WEBE29911の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider WEBE29911で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider WEBE29911を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider WEBE29911の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider WEBE29911に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider WEBE29911デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
