WeiderメーカーWEEVSY87210の使用説明書/サービス説明書
ページ先へ移動 of 30
USER'S MANUAL QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or if there are missing or damaged parts, please call: Or write: ICON Health & Fitness Ltd. Unit 4 Revie Road Industrial Estate Revie Road Beeston Leeds, LS1 1 8JG UK email: csuk@iconeurope.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The decals shown below have been placed on the weight system in the locations shown. If decals are missing or illegible, please call our Customer Service Department to order free replacement decals (see the back cover of this manual). Apply the decals in the locations shown.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 188 cm (74 in.) Width: 102 cm (40 in.) Length: 135 cm (53 in.) Foot Plate Low Pulley Station High Pulley Station Lat Bar Seat Leg Lever Butterfly Arms Press Arm Weight Stack Weight Pin Backrest Stepper Pedals Resistance Cylinders Thank you for selecting the versatile WEIDER ® 8515 weight system.
5 ASSEMBL Y 1 56 High Side of Bracket Handles 3 5 51 Long Side 31 51 14 1 1 27 4 Before beginning assembly , carefully read the following information and instructions: • Place all parts of the weight system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed.
6 FRAME ASSEMBL Y 2. Slide the Front Upright (42) onto the 5/16” x 2 1/2” Carriage Bolts (1) in the Base (4). Hand tighten a 5/16” Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. Press a 1” Square Inner Cap (65) into the Front Upright (42).
5. Lubricate the pedal axles on the Rear Upright (56). Slide the Left Pedal (79) onto the left pedal axle, and the Right Pedal (78) onto the right pedal axle. Note: Make sure that the Pedals are on the correct sides; the slot- ted brackets must be on the insides of the Pedals.
8 FRAME ASSEMBL Y ARM ASSEMBL Y 9. Press the Weight Tube Bumper (64) into the end of the Weight Tube (63). Insert the Weight Tube into the stack of W eights (25). Be sure that the pins on the Weight T ube are sitting in the pin grooves in the top Weight.
9 ARM ASSEMBL Y 12. Wet the handle of one Press Arm (46) with soapy water . Slide a 5” Plastic Grip (31) onto the handle. Press a 1” Round Inner Cap (49) into the other end of the handle. Press a 1 3/4” Square Inner Cap (44) into the top of the Press Arm.
10 CABLE ASSEMBL Y As you assemble the cables and pulleys in steps 14 through 22, please refer to the CABLE DIAGRAM on page 22 of this manual. 14. Route the Long Cable (23) around the 3 1/2” Pulley (15) attached to the T op Frame (55).
CABLE ASSEMBL Y 17 15 50 20 21 57 15 23 6 66 48 7 16 23 68 16. Route the Long Cable (23) around the “V”- Pulley (6) on the Right Arm (48). Be sure that the Cable is in the groove of the “V”-Pulley and that the Long Cable T rap (50) is turned to hold the Cable in place.
18. Route the Long Cable (23) around the 3 1/2” Pulley (15) attached to the bracket on the T op Frame (55). T ighten the 3/8” x 2” Bolt (12) and the 3/8” Nylon Locknut (21). (Note: This Pulley is pre-assembled. It has been shown disassembled for easy part identifi- cation.
CABLE ASSEMBL Y 12 3 6 9 58 15 21 66 92 9 17 20 21 2 2 10 58 67 10 57 58 20. Route the Short Cable (58) around the 3 1/2” Pulley (15) attached to the upper hole in the Press Frame (17). Be sure that the Cable T rap (66) is in the “3 o’clock” position and that the Cable is routed around the Pulley as shown.
14 CABLE ASSEMBL Y 22. Attach the Long Cable (23) to the Small “U”- Bracket (67) with a 1/4” Nylon Locknut (2) and a 1/4” W asher (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable so only a couple of threads are showing above the Nylon Locknut, as shown in the inset drawing.
15 25. Press a 1 1/2” Square Inner Cap (32) into the Leg Lever (29). Lubricate the 5/16” x 2 1/4” Bolt (33). Attach the Leg Lever (29) to the Seat Frame (36) with the 5/16” x 2 1/4” Bolt and a 5/16” Nylon Locknut (3). Insert the 3/8” x 2” Eyebolt (35) into the Leg Lever (29) from the direction shown.
16 28. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in HOW T O USE THE WEIGHT SYSTEM, beginning on page 17. Before using the weight system, pull each cable a few times to be sure that the cables move smoothly over the pulleys.
17 HOW T O USE THE WEIGHT SYSTEM The instructions below describe how each part of the weight system can be adjusted. IMPORT ANT : When attaching the lat bar or nylon strap, make sure that the attachments are in the correct starting position for the exercise to be performed.
18 A TT ACHING AND REMOVING THE SEA T Set the bracket on the Seat Frame (36) onto the indi- cated pins on the Front Upright (42). Attach the Seat Frame to the Front Upright with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40). For some exercises, the Seat (13) must be removed.
LOCKING THE WEIGHT ST ACK When the weight system is not in use, the Lock Pin (90) and Lock (91) should be attached. Insert the Lock Pin through a Weight Guide (62).
20 WEIGHT PRESS ARM BUTTERFL Y ARM LEG LEVER HIGH PULLEY LOW PULLEY PLA TES (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) To p 2 0 1 0 1 5 1 4 2 4 14 5 2 2 3 6 2 8 5 4 27 0 3 3 5 4 4 4 8 2 39 9 4 2 7 5 6 0 1 1 5.
21 TROUBLESHOOTING AND MAINTENANCE Inspect and tighten all parts often and replace any worn parts immediately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used.
22 4 3 2 7 6 5 4 3 2 Weight Stack— 8 1 —Low Pulley 1 —High Pulley Long Cable (23) 5 —Long “U”-Bracket Short Cable (58) TOP V IE W CABLE DIAGRAM The cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23).
NOTES 23.
ORDERING REPLACEMENT P ARTS If you encounter any difficulties or problems with this product, contact the ICON Fitness Lifestyle Ltd. of fice, or write: ICON Health & Fitness Ltd.
IMPORT ANT: Assembly is divided into four stages: 1) frame assembly , 2) arm assembly , 3) cable assembly , and 4) seat assembly . The hardware for each stage is packaged separately . W ait until you begin each assem- bly stage to open that parts bag.
1" Round Inner Cap (49) 1" Round Cover Cap (70) 3/4" Round Inner Cap (34) 1/2" x 3/4" Spacer (61) 1 1/2" Square Inner Cap (32) 1 3/4" Square Inner Cap (44) 2" S.
5/16" Nylon Locknut (3) 1/4" W asher (10) 5/16" W asher (8) 1" Retainer (69) 1/4" x 2 1/2" Screw (43) 5/16" x 1 3/4" Bolt (72) 1/4" x 2" Machine Screw.
81 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL SA VE THIS P ART LIST/EXPLODED DRA WING FOR FUTURE REFERENCE.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover for information about ordering replacement parts.
23 11 11 8 8 55 27 12 15 44 15 71 23 21 44 21 3 61 60 3 3 5 51 14 19 26 51 25 64 63 3 76 72 9 92 3 3 4 1 27 65 41 10 43 3 21 6 50 7 42 7 50 6 21 69 70 69 70 47 48 44 45 44 45 52 53 39 49 62 2 10 67 54.
デバイスWeider WEEVSY87210の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Weider WEEVSY87210をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider WEEVSY87210の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider WEEVSY87210の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider WEEVSY87210で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider WEEVSY87210を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider WEEVSY87210の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider WEEVSY87210に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider WEEVSY87210デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。