WeiderメーカーWESY13820の使用説明書/サービス説明書
ページ先へ移動 of 24
USER'S MANUAL CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. WESY13820 Model Number Decal (under seat) QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction.
2 WEIDER is a registered trademark of ICON Health & Fitness, Inc. IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . .
3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN Thank you for selecting the versatile WEIDER ® 950 weight system. The WEIDER ® 950 weight system offers a selection of weight stations designed to devel- op every major muscle group of the body .
5 Before beginning assembly , carefully read the following information and instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
6 2. Press a 50mm Square Inner Cap (44) into the top of the Rear Upright (3). Attach the Rear Upright (3) to the Stabilizer (2) with the M8 x 67mm Carriage Bolts (66) and two M8 Nylon Locknuts (61). Attach the Front Upright (4) to the Base (1) with the two M8 x 63mm Carriage Bolts (65) and two M8 Nylon Locknuts (61).
7 5. Press two 25mm x 50mm Inner Cap (42) into the top of the Press Frame (9). Press two 50mm Square Inner Caps (44) into the ends of the Press Frame. Orient the Press Frame (9) with the bracket on the side shown. Attach the Press Frame to the T op Frame (5) with an M10 x 125mm Bolt (54), two M10 W ashers (55), and an M10 Nylon Locknuts (56).
8 10. Route the High Cable (35) down through the T op Frame (5) and around a Pulley (39). Attach the Pulley and a Cable T rap (41) to the second set of holes from the top of the two Pulley Plates (14) with an M10 x 48mm Bolt (77) and an M10 Nylon Locknut (56).
9 14. Wrap the Arm Cable (36) around a “V”-Pulley (38). Attach the Pulley and a Long Cable T rap (40) to a Pulley Bracket (30) with an M10 x 55mm Bolt (69) and an M10 Nylon Locknut (56). Be sure the Cable T rap is turned to hold the Cable in the groove of the Pulley .
10 17. Slide the Arm Cable (36) onto the hook on the Left Arm (1 1). 18. Locate the Short Cable (80). Attach the Cable to the side of the Base (1) with an M10 x 70mm Bolt (82), an M10 W asher (55), and an M10 Nylon Locknut (56). 16. Wrap the Arm Cable (36) around a “V”-Pulley (38).
11 20. Attach the Short Cable (80) to the “U”-Bracket (81) with an M8 W asher (76) and an M8 Nylon Locknut (61). Note: Do not completely tighten the Locknut; it should be threaded only two turns onto the end of the Cable, as shown in the inset drawing.
12 24. Wrap the Low Cable (37) around a Pulley (39). Attach the Pulley inside the bracket on the Base (1) with an M10 x 45mm Bolt (68) and an M10 Nylon Locknut (56).
13 28. Insert an M6 x 50mm Carriage Bolt (62) into the center hole in the Seat Plate (24). Attach the Seat Plate to the Seat (17) with two M6 x 16mm Screws (59). Attach the Seat (17) to the Seat Frame (6) with the M6 x 50mm Carriage Bolt (62), an M6 x 50mm Screw (64), two M6 W asher (63), and an M6 Nylon Locknut (58).
34. Make sure that all parts have been properly tightened. The use of all remaining parts will be explained in ADJUSTMENTS, on the next page. Before using the weight system, pull each cable a few times to make sure that the cables move smoothly over the pulleys.
15 This section explains how to adjust the weight system. Refer to the accompanying exercise guide to see the cor- rect form for each exercise. Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immediate- ly .
16 28 29 CONVERTING THE ARMS To use the Arms (10, 1 1) as butterfly arms, remove the Arm Pins (28) and engage the Arm Latch (29) into the hole in the Press Frame (9). To use the Arms (10, 1 1) as press arms, insert the two Arm Pins (28) into the holes in the Press Frame (9) and the Arms.
WEIGHT (lbs.) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 11 0 11 5 120 125 PRESS ARM (lbs.) 18 26 34 42 50 58 64 70 76 82 88 97 106 11 5 124 133 138 143 148 153 158 166 174 183 191 201 BUTTERFL Y ARM (lbs.) 12 16 20 24 28 33 37 41 45 49 53 57 61 65 69 73 77 81 85 89 93 97 101 105 109 11 2 LOW PULLEY (lbs.
High Cable (35) CABLE DIAGRAMS The cable diagrams below show the proper routing of the High Cable (35), the Arm Cable (36), the Low Cable (37), and the Short Cable (80). Use the diagrams to make sure that the cables and the cable traps have been assembled correctly .
19 TIGHTENING THE CABLES W oven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened.
M10 Nylon Locknut (56) M8 Nylon Locknut (61) M6 Nylon Locknut (58) 19mm Round Inner Cap (49) 50mm Square Inner Cap (44) 25mm x 50mm Inner Cap (42) 45mm Square Inner Cap (45) 38mm Square Inner Cap (48) 50mm Square Outer Cap (50) Dome Cap (47) Large W asher (67) 25mm Round Inner Cap (43) P ART IDENTIFICA TION CHART—Model No.
M6 W asher (63) M8 x 70mm Bolt (51) M6 x 16mm Bolt (59) M10 x 65mm Grade 5 Bolt (73) M10 x 55mm Bolt (69) M10 x 20mm Bolt (75) M10 x 45mm Bolt (68) M10 x 78mm Bolt (71) M10 x 48mm Bolt (77) M10 x 125m.
Key No. Qty . Description Key No. Qty . Description 11 Base 21 Stabilizer 31 Rear Upright 41 Front Upright 51T op Frame 61 Seat Frame 71 Leg Lever 81C u rl Post 91P r ess Frame 10 1 Right Arm 11 1 Lef.
EXPLODED DRA WING—Model No. WESY13820 R0902B 61 81 80 76 56 77 39 41 13 12 33 33 39 68 56 39 77 56 5 39 74 73 44 61 72 25 55 61 60 35 56 55 74 71 56 30 38 40 36 44 45 9 56 55 55 54 42 43 28 58 57 19.
ORDERING REPLACEMENT P ARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.
デバイスWeider WESY13820の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Weider WESY13820をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider WESY13820の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider WESY13820の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider WESY13820で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider WESY13820を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider WESY13820の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider WESY13820に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider WESY13820デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。