WeiderメーカーWESY16010の使用説明書/サービス説明書
ページ先へ移動 of 28
USER'S MANUAL ® Model No. WESY16010 Serial No. (Write the serial number in the space above for reference.) Serial Number Decal (under seat) Visit our website at www .
2 T ABLE OF CONTENTS FULL 90-DA Y WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual and in the accompanying literature before using the home gym. 2. It is the responsibility of the owner to ensure that all users of the home gym are adequate- ly informed of all precautions. 3. The home gym is intended for home use only .
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 76 in. Width: 37 in. Length: 48 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Press Arm Weight Carriage Seat Backrest Thank you for selecting the versatile WEIDER ® 8920 home gym.
5 ASSEMBL Y 1 56 3 5 51 51 14 1 27 4 Before beginning assembly , carefully read the following information and instructions: • Place all parts of the home gym in a cleared area and remove the packing materials; do not dis- pose of the packing materials until assembly is completed.
6 FRAME ASSEMBL Y 2. Refer to drawing 2a. Press a 1” Inner Cap (61) into each end of the weight tube on the Weight Carriage (19). Note: The Square Slider Bushings (70) should be pre-assem- bled to the Weight Carriage (19) and W eight Stop (67).
7 ARM ASSEMBL Y 5. Press a 1 3/4” Square Inner Cap (44) into the top of one of the Press Arms (46). Press a 1” Round Inner Cap (49) into each end of the handle on the Press Arm. Attach the Press Arm to one side of the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3).
8 CABLE ASSEMBL Y 11 8 9 10 58 58 55 16 25 Hook Ball 15 50 58 7 47 58 21 7 21 6 50 23 6 42 8. During steps 9 through 22, refer to the CABLE DIAGRAM on page 19 of this manual to verify proper cable routing. Before begin- ning this section, identify the Short Cable (23) and the Long Cable (58) by comparing the lengths and the ends of the cables.
9 CABLE ASSEMBL Y 12 48 21 50 7 6 58 12. Route the Long Cable (58) around a “V”- Pulley (6). Be sure that the Cable is in the groove of the “V”-Pulley and that a Long Cable T rap (50) is turned to hold the Cable in place.
10 CABLE ASSEMBL Y 17 21 15 59 15 66 9 9 Bracket 17 16 16. Attach the Long Cable (58) to the Weight Carriage (19) with a 3/8” x 3/4” Bolt (69) and a 3/8” Nylon Locknut (21).
11 CABLE ASSEMBL Y 19. Slide a Cable T rap (66) and a 3 1/2” Pulley (15) onto each 3/8” x 3 3/4” Bolt (68). Insert the Bolts into the Front Upright (42) from the direction shown. Hand tighten a 3/8” Nylon Locknut (21) with a 3/8” Flat W asher (9) onto each Bolt.
22. Attach the end of the Short Cable (23) to the Long “U”-Bracket (57) with a 1/4” Nylon Lock- nut (2) and a 1/4” Flat W asher (10). Do not completely tighten the Nylon Locknut; it should be threaded onto the end of the Cable until two threads are showing above the Nylon Locknut, as shown in the inset drawing.
13 24. Press a 1 1/2” Square Inner Cap (32) into the Seat Frame (36). Insert the 1/4” x 2” Carriage Bolt (38) into the center hole in the Seat Plate (37). Attach the Seat Plate to the Seat (13) with two 1/4” x 3/4” Screws (18). Insert the 1/4” x 2” Carriage Bolt (38) into the indicated hole in the Seat Frame (36).
14 27. Press 3/4” Round Inner Caps (34) into the ends of both Pad T ubes (28). Insert one Pad T ube (28) into the Seat Frame (36). Slide a Foam Pad (30) onto each end of the Pad T ube. Insert the other Pad T ube (28) into the Leg Lever (29). Slide a Foam Pad (30) onto each end of the Pad T ube.
15 ADJUSTMENT The instructions below describe how each part of the home gym can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym should be set up for each exercise.
16 A TT ACHING AND REMOVING THE SEA T Set the bracket on the Seat Frame (36) onto the indi- cated pins on the Front Upright (42). Attach the Seat Frame to the Front Upright with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40). For some exercises, the Seat (13) must be removed.
17 WEIGHT ON PRESS ARM BUTTERFL Y ARM LOW PULLEY/ HIGH PULLEY WEIGHT (lbs.) (lbs.) LEG LEVER (lbs.) CARRIAGE (lbs.) 0 12 7 10 10 52 2 1 1 1 8 1 6 10 31 15 25 21 15 40 20 32 26 20 50 24 39 32 25 59 29 .
18 TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym. Replace any worn parts immediately . The home gym can be cleaned using a damp cloth and mild non-abrasive detergent.
19 CABLE DIAGRAM The cable diagram below shows the proper routing of the Short Cable (23) and the Long Cable (58). Use the diagram to be sure that the two cables and the cable traps have been assembled correctly . If the cables have not been correctly routed, the home gym will not function properly and damage may occur .
20 NOTES.
21 NOTES.
22 Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. P ART LIST—Model No. WESY16010 R0801A Key No.
56 15 12 2 57 23 21 3 5 51 14 51 4 1 27 68 7 50 6 21 63 62 63 62 47 48 44 45 44 45 13 40 38 37 18 32 28 30 34 10 2 24 36 30 34 14 33 3 29 34 30 28 9 21 49 46 32 30 34 35 49 49 46 22 3 9 16 23 59 17 21.
Part No. 178217 R0801A Printed in Canada © 2001 ICON Health & Fitness, Inc. ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.
This chart is provided to help you identify the small parts used in assembly . Important: S ome parts ma y have been pre-assembled for shipping purposes; if you cannot find a part in the parts bags, check to see i f i t h a s bee n pre-assembled.
1 3/4" Square Inner Cap (44) 1 1/2" Square Inner Cap (32) 2" Square Inner Cap (27) 2" Square Outer Cap (51) 1" Square Inner Cap (65).
5/16" Nylon Jamnut (72) 3/8" x 2 1/2" Eyebolt (35) 3/4" Round Inner Cap (34) 1" Round Inner Cap (49) 1" Round Cover Cap (62) 1" Inner Cap (61) 3/8" Flat W asher.
1/4" x 2" Screw (24) 1/4" x 2 1/2" Screw (43) 5/16" x 2 1/2" Bolt (22) 5/16" x 4 3/4" Bolt (64) 1/4" x 2" Carriage Bolt (38) 3/8" x 3/4" Bol.
デバイスWeider WESY16010の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Weider WESY16010をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider WESY16010の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider WESY16010の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider WESY16010で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider WESY16010を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider WESY16010の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider WESY16010に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider WESY16010デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
