WeiderメーカーWESY19002の使用説明書/サービス説明書
ページ先へ移動 of 24
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, we will guarantee complete satisfaction through direct assistance from our factory . TO A VOID UNNECESSAR Y DELA YS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUST OMER HOT LINE.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual and in the accompanying literature before using the training system. Use the training system only as described in the literature. 2. It is the responsibility of the owner to ensure that all users of the training system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arm Curl Pad Curl Frame Press Arm We ight Stack Backrest Shroud Seat Thank you for selecting the versatile WEIDER ® 245 training system. The WEIDER ® 245 of fers a selection of weight stations designed to develop every major muscle group of the body .
1/4" Nylon Lockn ut (2) 1/2" x 1/2" Spacer (61) 5/16" Nylon Jamnut (87) 1/4" W asher (78) 5/16" SAE W asher (88) 5/8" x 1/2" Spacer (82) 3/8" Nylon Jamnut .
5/16" x 2 3/4" Shoulder Bolt (85) 1/4" x 2 1/4" Carriage Bolt (38) 5/16" x 6" Bolt (60) 3/8" x 5" Bolt (75) 3/8" x 4 1/4" Bolt (64) 3/8" x 4".
7 ASSEMBL Y Make sure you have the following tools: • T wo (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • One (1) rubber mallet •Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
3 4 FRAME ASSEMBL Y 8 1 21 42 4 19 25 Pin Groove 62 3. Attach the Front Upright (42) to the Base (4) using two 3/8” x 2 1/4” Bolts (1) and two 3/8” Nylon Locknuts (21). Do not tighten the Nylon Locknuts yet. 4. Slide a Weight Bumper (19) down over each W eight Guide (62).
5. Insert the Weight Tube Cap (72) into the indi- cated end of the Weight Tube (63). Slide the W eight Tube into the center holes in the We ights (25). Slide the T op Weight (56) down onto the Weight Guides (62) as shown. 6. Press four 1 1/2” x 2 1/2” Inner Caps (27) into the T op Frame (55).
ARM ASSEMBL Y FRAME ASSEMBL Y 8. Attach the T op Frame (55) to the Weight Guides (62) using a 5/16” x 6” Bolt (60), two 1/2” x 1/2” Spacers (61), and a 5/16” Nylon Locknut (3) as shown. T ighten all Nylon Locknuts used in steps 3 through 8. 9.
11 ARM ASSEMBL Y 11 . Attach the Seat Plate (37) to the Seat Frame (36) using a 1/4” x 2 1/4” Carriage Bolt (38), a 1/4” Flat W asher (78), and a 1/4” Nylon Locknut (2). 12. Attach a Bumper (1 1) to the Seat Frame (36) using a #10 x 1” Screw (80).
18 15 48 47 Bracket Lubricate Axle 55 65 68 45 44 47 16 17 CABLE ASSEMBL Y ARM ASSEMBL Y 12 15. Press a 1 3/4” Square Inner Cap (44) into the lower end of the Left Arm (47). Using a small amount of soapy water , slide a Large Foam Pad (45) onto the Left Arm.
19. Route the Short Cable (23) around two “V”- Pulleys (6). Attach the Pulleys and two Long Cable T raps (50) to the Left Arm (47) and the Right Arm (48) as shown, using two 3/8” x 2 1/2” Bolts (7) and two 3/8” Nylon Locknuts (21). Do not overtighten the Nylon Locknuts; the Pulleys must be able to turn freely .
26 23 24 25 23. Locate the Long Cable (69). Route the Long Cable between the Base (4) and the Press Frame (17) as shown. Lay the Long Cable in the bracket on the Base. Attach the Pro-Pulley (77) to the bracket using a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21).
27. Route the Long Cable (69) behind the Press Frame (17) and under the Seat Frame (36) as shown. Route the Long Cable around two 3 1/2” Pulleys (15). Slide the 3/8” x 5” Bolt (75) through the 3 1/2” Pulleys (15), two Cable T raps (66), and the Press Frame (17) as shown.
31. Attach the Seat (13) to the Seat Frame (36) using two 1/4” x 3/4” Bolts (18), a 1/4” x 2 1/4” Bolt (33), and a 1/4” W asher (78). 32. Attach the Backrest (41) to the Front Upright (42) using two 1/4” x 3” Bolts (43) and two 1/4” W ashers (78).
35. Attach the Shroud (59) to the brackets on the T op Frame (55) and the Base (4) using four #8 x 1/2” Screws (79). 17 35 79 79 59 55 79 4 SEA T ASSEMBL Y 36. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT , beginning on page 18 of this manual.
18 54 39 53 53 52 23 25 26 CHANGING THE WEIGHT SETTING To change the weight setting of the weight stack, insert the Weight Pin (26) under the desired W eight (25). Be sure to insert the Weight Pin until the bent end of the Weight Pin is touching the W eights, and turn the bent end downward.
19 This chart shows the approximate weight resistance at each exercise station. “T op” refers to the 6.5 lb. top weight. The other numbers refer to the 10 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
20 TROUBLE-SHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the training system. Replace any worn parts immedi- ately . The training system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
21 CABLE DIAGRAM The diagram below shows the proper routing of the Short Cable (23) and the Long Cable (69). Use the diagram to be sure that the cables and the cable traps have been assembled correctly . If the cables have not been cor- rectly routed, the training system will not function properly and damage may occur .
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. P ART LIST—Model No. WESY19002 R0303A Key No. Qty .
2 21 66 15 64 9 21 21 8 43 21 68 65 48 42 45 44 79 79 79 79 3 61 62 60 23 86 57 56 63 26 25 73 14 73 5 21 58 15 15 12 58 1 4 3 3 21 21 21 19 19 77 12 27 53 21 21 15 17 16 52 39 22 3 15 75 46 46 31 49 .
ORDERING REPLACEMENT P ARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.
デバイスWeider WESY19002の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Weider WESY19002をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider WESY19002の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider WESY19002の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider WESY19002で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider WESY19002を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider WESY19002の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider WESY19002に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider WESY19002デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。