WeiderメーカーWESY19740の使用説明書/サービス説明書
ページ先へ移動 of 28
CAUTION Read all precautions and instruc - tions in this manual before using this equipment. Save this manual for future reference. Model No. WESY19740 Serial No.
2 W ARNING DECAL PLACEMENT WEIDER is a registered trademark of ICON IP , Inc. T ABLE OF CONTENTS The decals shown here have been placed on the weight system. If a decal is missing or illegible, please call our Customer Service Department toll-free at 1-877-992-5999, Monday through Friday , 6 a.
1. Read all instructions in this manual before using the weight system. Use the weight sys- tem only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
ASSEMBLED DIMENSIONS: Height: 76 in. Width: 38 in. Depth: 65 in. 4 Shroud High Pulley Station Low Pulley Station Right Side Left Side Note: The terms “right side” and “left side” are determined relative to a person sitting on the seat; they do not corre- spond to right and left on the drawings in the manual.
Make sure you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • One Allen Wrench (included) • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
6 2. Attach the Base (1) and the two Weight Guides (21) to the Stabilizer (2) with two M10 x 67mm Bolts (71), two M10 W ashers (57), and two M10 Nylon Locknuts (56). Make sure the indicated holes in the Weight Guides are nearer the bot- tom. Fully tighten the Locknuts.
7 3. Attach the Front Leg (7) to the Base (1) with the two indicated M8 x 63mm Carriage Bolts (78) and two M8 Nylon Locknuts (58). Do not tighten the Locknut yet. Attach the Leg Bumper (60) to the Front Leg (7) with an M4 x 20mm Self-tapping Screw (69) and an M4 W asher (33).
8 6. Attach the T op Frame (4) to the Upright (3) with two M8 x 65mm Bolts (68), two M8 W ashers (59), and two M8 Nylon Locknuts (58). Do not tighten the Locknuts yet. Attach the T op Frame (4) between the W eight Guides (21) with an M10 x 155mm Bolt (74), two M10 W ashers (57), two 19mm Spacers (76), and an M10 Nylon Locknut (56).
9 8. Attach the Shroud (17) to the T op Frame (4) with two M6 x 16mm Screws (62) and two M6 W ashers (82). Attach the Shroud (17) to the brackets on the Stabilizer (2) with two M6 x 16mm Screws (62) and two M6 W ashers (82). Make sure the brack- ets are inside the Shroud.
10 1 1. Grease an M10 x 51mm Bolt (66). Attach a Cable Pivot (39) to the Right Arm (9) with the Bolt and an M10 Nylon Locknut (56). Do not overtighten the Locknut; the Cable Pivot must be able to pivot easily . Wet the inside of a Large Foam Pad (42) with soapy water .
1 1 14. Route the Arm Cable (54) over a “V”-pulley (46). Attach the “V”-pulley , a Large Cable T rap (50), two Full Finger Guards (41), and an M10 W asher (57) to the Upright (3) with an M10 x 63mm Bolt (75) and an M10 Nylon Locknut (56). Make sure the Cable T rap is oriented to hold the Cable in the groove of the “V”-pulley .
12 18. Locate the Low Cable (53). Route the Cable through the Leg Lever (8) and the Front Leg (7). Attach a 90mm Pulley (48) inside of the Leg Lever (8), over the Low Cable (53), with an M10 x 67mm Bolt (71), two M10 W ashers (57), two 12mm Spacers (52), and an M10 Nylon Locknut (56).
13 22. Route the Low Cable (53) under a 90mm Pulley (48). Attach the Pulley and two Half Finger Guards (43) to the Base (1) with an M10 x 46mm Bolt (81) and an M10 Nylon Locknut (56). Make sure the Finger Guards are on the outside of the bracket as shown.
14 26. Wrap the High Cable (55) under a 90mm Pulley (48). Attach the Pulley , a Cable T rap (51), and two Half Finger Guards (43) at the upper hole in the “U”-bracket (45) with an M10 x 51mm Bolt (66) and an M10 Nylon Locknut (56).
15 30. Attach the Backrest (16) to the Upright (3) with two M6 x 63mm Screws (70) and two M6 W ashers (82). 32. Attach the Lock Plate (73) to the Front Leg (7) with an M10 x 70mm Bolt (86), an M10 W asher (57), and an M10 Nylon Locknut (56). Do not overtighten the Locknut; the Lock Plate must be able to pivot easily .
16 34. Orient the Curl Pad (14) so that the holes on the back are closer to the lower edge. Attach the Curl Pad to the Curl Post (13) with two M6 x 16mm Screws (62). 35. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENTS, beginning on the following page.
This section explains how to adjust the weight system. See the EXERCISE GUIDELINES on page 22 for impor- tant information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for each exercise.
18 5 21 89 88 ARM CONVERSION T o use the Arms (9, 10) as butterfly arms, insert the Arm Pins (40) into the holes in the Upright (3) and the Pivot Frame (5) as shown. T o use the Arms (9, 10) as press arms, insert the Arm Pins (40) into the holes in the Pivot Frame (5) and Arms.
19 WEIGHT RESIST ANCE CHART The chart below shows the approximate weight resistance at each exercise station. “T op” refers to the 6 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. W eight resistance shown for the butterfly arm sta- tion is for each arm.
CABLE DIAGRAMS The cable diagrams below show the proper routing of the Low Cable (53), the Arm Cable (54), and the High Cable (55). Use the diagrams to make sure that the cables, cable traps, and finger guards have been assem- bled correctly .
Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts imme- diately . The weight system can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used.
22 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise.
23 Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout.
M6 W asher (82) M8 Nylon Locknut (58) M6 Locknut (87) M8 W asher (59) M10 Nylon Locknut (56) M4 W asher (33) M10 x 70mm Bolt (86) M10 x 51mm Bolt (66) M10 x 46mm Bolt (81) M10 x 63mm Bolt (75) M10 x 6.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user ’ s manual for information about ordering replacement parts.
1 56 79 5 67 67 57 57 69 57 56 56 40 58 39 54 65 66 44 44 56 83 66 44 44 56 65 54 39 58 42 42 11 11 31 31 71 13 14 62 36 35 36 37 15 6 70 70 68 68 68 68 61 58 58 56 57 30 28 34 34 29 28 69 33 30 56 79.
2 3 30 30 26 22 27 27 21 57 56 57 24 23 25 85 84 55 74 56 55 48 30 52 57 71 47 52 57 56 4 56 57 57 49 52 48 30 52 49 57 57 71 18 17 62 53 43 66 43 48 56 51 58 59 45 19 62 64 20 62 32 16 70 82 56 56 41.
Part No. 217700 R0904B Printed in China © 2004 ICON IP , Inc. LIMITED W ARRANTY ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate- rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase.
デバイスWeider WESY19740の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Weider WESY19740をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider WESY19740の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider WESY19740の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider WESY19740で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider WESY19740を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider WESY19740の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider WESY19740に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider WESY19740デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。