WeiderメーカーWESY29521の使用説明書/サービス説明書
ページ先へ移動 of 32
USER'S MANUAL CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. WESY29521 Serial No. Write the serial number in the space above for reference. Serial Number Decal (under seat) Visit our website at www .
2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 77 in. Width: 81 in. Length: 59 in. Foot Plate Low Pulley Station Ab Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arm Press Arm Weight Seat Seat Backrest Backrest Leg Press Plate Thank you for selecting the versatile WEIDER ® PRO 3200 weight system.
75 5 Before beginning assembly , carefully read the following information and instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
6 4. Press a 50mm x 70mm Inner Cap (22) into the top of the Right Leg (73). Attach the Right Leg (73) to the Right Base (1) with the two indicated M10 x 65mm Carriage Bolts (57) and two M10 Nylon Locknuts (70). Attach the Right Upright (6) to the Right Base (1) with the two indicated M10 x 65mm Carriage Bolts (57) and two M10 Nylon Locknuts (70).
7 7. Set two Weight Bumpers (83) over the indicated holes in the Center Base (67). Insert the two Weight Guides (20) into the holes. Attach the Weight Guides to the Center Base with two M10 x 65mm Bolts (63), four M10 W ashers (75), and two M10 Nylon Locknuts (70).
8 10. Press a 50mm x 70mm Inner Cap (22) into the end of the Right T op Frame (8). Attach the Right T op Frame (8) to the Right Upright (6) with two M10 x 90mm Bolts (59), a Support Plate (21), and two M10 Nylon Locknuts (70).
9 13. Lubricate an M10 x 50mm Bolt (62) with grease. Attach the Pivot Bracket (48) to the Right Butterfly Arm (1 1) with the Bolt and an M10 Nylon Locknut (70). Do not overtighten the Locknut; the Pivot Bracket must be able to pivot easily . Press a 40mm x 50mm Inner Cap (23) into the indicated end of the Right Butterfly Arm (1 1).
10 16. Press a 50mm x 70mm Inner Cap (22) into the top of the Leg Press Frame (30). Lubricate an M10 x 80mm Bolt (61) with grease. Attach the Leg Press Frame (30) to the Left Base (2) with the Bolt and an M10 Nylon Locknut (70). Do not overtighten the Locknut; the Leg Press Frame must be able to pivot easily .
1 1 20. Note: The following drawings are shown from the left side of the weight system, with the Left T op Frame (3) removed for clarity . W rap the High Cable (45) around a 90mm Pulley (38). Attach the Pulley at the rear hole, inside of the bracket on the Center T op Frame (14) with an M10 x 45mm Bolt (66) and an M10 Nylon Locknut (70).
12 23. Locate the Leg Press Cable (95). Attach the Cable inside the Left Leg (36) with aM10 x 70mm Bolt (81), two M10 W ashers (75), two Long Spacers (80), and an M10 Nylon Locknut (70).
13 27. Attach the end of the Leg Press Cable (95) to the “U”-Bracket (85) with an M8 W asher (26) and an M8 Nylon Locknut (71). Note: Do not complete- ly tighten the Locknut; it should be threaded only two turns onto the end of the Cable, as shown in the inset drawing.
14 31. W rap the Butterfly Cable (46) around a “V”-Pulley (39). Attach the Pulley and a Long Cable T rap (40) to the bracket on the Right Upright (6) with an M10 x 60mm Bolt (65) and an M10 Nylon Locknut (70). Be sure the Cable T rap is turned to hold the Cable in the groove of the Pulley .
15 35. W rap the Leg Lever Cable (96) around a 90mm Pulley (38). Attach the Pulley and a Cable T rap (91) to the Right Upright (6) with an M10 x 95mm Bolt (98), an M10 W ashers (75), and an M10 Nylon Locknut (70). Be sure the Cable T rap is turned to hold the Cable in the groove of the Pulley .
16 39. Route the Low Cable (47) through the Left Leg (36) and the Left Upright (7). Attach a 90mm Pulley (38) inside the Upright with an M10 x 70mm Bolt (81), two M10 W ashers (75), two 13mm Spacers (34), and an M10 Nylon Locknut (70). 40. Wrap the Low Cable (47) around a 90mm Pulley (38).
17 41. W rap the Low Cable (47) around a 90mm Pulley (38). Attach the Pulley to the indicated bracket on the Left Base (2) with an M10 x 45mm Bolt (66) and an M10 Nylon Locknut (70).
18 45. W rap the Low Cable (47) around a 90mm Pulley (38). Attach the Pulley and a Cable T rap (91) to the indicated bracket on the Right Base (1) with an M10 x 45mm Bolt (66) and an M10 Nylon Locknut (70). Be sure the Cable T rap is turned to hold the Cable in the groove of the Pulley .
19 50. Press two 20mm x 40mm Inner Caps (104) and a 25mm x 40mm Inner Cap (105) into the Adjustable Backrest Frame (101). Attach a Backrest (15) to the Adjustable Backrest Frame (101) with four M6 x 16mm Bolts (13). Insert the Adjustable Backrest Frame (101) into the Right Upright (6) and secure it with an Adjustment Knob (102).
This section explains how to adjust the weight system. See the EXERCISE GUIDELINES on page 26 for impor- tant information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for each exercise.
21 86 72 CHANGING THE WEIGHT SETTING T o change the weight setting of the weight stack, insert the Weight Pin (86) under the desired W eight (72). Be sure to insert the Weight Pin until the bent end of the Weight Pin is touching the W eights, and turn the bent end downward.
22 TIGHTENING THE CABLES W oven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened.
23 WEIGHT RESIST ANCE CHART The chart below shows the approximate weight resistance at each exercise station. “T op” refers to the 6-pound top weight. The other numbers refer to the 12.5-pound weight plates. W eight resistance shown for the butterfly arm station is for each butterfly arm.
High Cable (45) CABLE DIAGRAMS The cable diagrams below show the proper routing of the High Cable (45), the Butterfly Cable (46), the Low Cable (47), the Leg Press Cable (95), and the Leg Lever Cable (96). Use the diagrams to make sure that the cables and the cable traps have been assembled correctly .
25 4 1 2 5 2 1 3 5 Leg Lever Cable (96) Leg Press Cable (95) 3 4 CABLE ID CHART — (46) 47 3/7” — (96) 95 1/2” — (95) 148 1/4” — (47) 276 3/4” — (45) 1 16 3/4”.
26 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise.
27 Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout.
50mm x 70mm Inner Cap (22) 40mm x 50mm Inner Cap (23) 25mm Round Inner Cap (24) 19mm Round Inner Cap (27) 50mm Square Inner Cap (33) 38mm Square Inner Cap (41) M10 Nylon Locknut (70) M8 Nylon Locknut (71) M6 W asher (35) M8 W asher (26) M5 W asher (50) M10 W asher (75) P ART IDENTIFICA TION CHART—Model No.
M10 x 60mm Bolt (65) M10 x 90mm Bolt (59) M10 x 65mm Bolt (63) M10 x 85mm Bolt (60) M10 x 80mm Bolt (61) M10 x 95mm Bolt (98) M10 x 65mm Carriage Bolt (57) M10 x 50mm Bolt (62) M10 x 45mm Bolt (66) M1.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. P ART LIST—Model No. WESY29521 R1002B 1 1 Right Base 2 1 Left Base 3 1 Left T op Frame 4 1 Leg Le.
2 7 66 70 81 67 5 6 15 16 38 39 39 40 41 40 98 90 70 70 70 70 65 65 70 70 70 75 75 35 13 1 28 38 57 70 66 70 57 70 70 63 70 81 38 47 57 70 57 13 70 38 70 66 21 59 8 22 53 54 54 9 97 97 61 70 68 22 54 .
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
デバイスWeider WESY29521の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Weider WESY29521をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider WESY29521の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider WESY29521の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider WESY29521で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider WESY29521を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider WESY29521の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider WESY29521に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider WESY29521デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
