WeiderメーカーWESY2966.0の使用説明書/サービス説明書
ページ先へ移動 of 20
Visit our website at www .weiderfitness.com new products, prizes, fitness tips, and much more! V CAUTION Read all precautions and instruc - tions in this manual before using this equipment. Save this manual for future reference. Model No. WESY2966.0 S erial No.
2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual and all warnings on the resistance system before using the resistance system. Use the resist- ance system only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the resistance system are adequately informed of all precautions.
ASSEMBLED DIMENSIONS: Height: 82 in. / 208 cm Width: 66 in. / 168 cm Depth: 44 in. / 1 12 cm 4 Resistance Bars Pulley Housing Upright Handle Short Cable Squat Bar Upright Base Base Right Side Left Sid.
M6 W asher (60) M8 W asher (54) M8 Nylon Locknut (57) M10 W asher (59) M10 Nylon Locknut (56) M10 x 70mm Button Bolt (69) M10 x 47mm Button Screw (76) M8 x 100mm Button Bolt (70) M4 x 12mm Flat Head S.
6 ASSEMBL Y 1. Attach three Plastic Feet (1) to the Base (2) with three M4 x 16mm Screws (61). Attach the Upright Base (5) to the Base (2) with two M10 x 60mm Button Bolts (67), two M10 W ashers (59), two M10 x 102mm Button Bolts (65), and four M10 Nylon Locknuts (56).
7 2. Attach the Base Cover (4) to the Base (2) with two M4 x 50mm Screws (66). Do not over- t ighten the Screws (66). If you overtighten the Screws, you will damage the Base C over . See the inset drawing. Attach a Cable Clip Hook (86) to the Upright Base (5) with two M5 x 16mm Screws (78).
8 4. Attach the two 10-pound Short Caps (81) to the 10-pound Center Bar (45) with two M4 x 12mm F lat Head Screws (58). U sing ten M4 x 12mm Flat Head Screws (58), attach the two 10-pound Caps (53) to.
9 9. Attach a Pulley Bracket (17) to the indicated “U”-channel (18) with an M10 x 132mm Button Bolt (72), two M10 W ashers (59), and an M10 Nylon Locknut (56). Wrap the Long Cable (42) over a 90mm Pulley (38). Attach the Pulley inside the Pulley Bracket (17) with an M10 x 42mm Button Bolt (71) and an M10 Nylon Locknut (56).
10 1 1. Route the Long Cable (42) under a 90mm Pulley (38). Attach the Pulley , a Cable T rap ( 39), and two Half Guards (37) to the indicated hole in the Base (2) (see the inset drawing) with a n M10 x 52mm patch Screw (76) and an M10 W asher (59). Make sure that the Cable T rap is oriented to hold the Cable in the groove of the Pulley .
1 1 14. Note: This step may be easier if the resist- ance system is tipped forward as shown. Wrap the wire found inside the in the Rear F rame (10) around the end of the Long Cable (42). Pull the Long Cable through the Rear Frame and out of the Swivel Arm (12).
12 19. Slide four Foam Pads (32) onto the Pad T ube (35) and the Leg Lever (9). Press a 19mm Round Inner Cap (33) into each Foam Pad. 20. Set the Seat Frame (8) onto the Upright Base (5) as shown. 21. Make sure that all parts have been properly tightened.
13 This section explains how to adjust the resistance system. See the EXERCISE GUIDELINES on page 16 for important information about how to get the most benefit from your exercise program. Also, refer to the accompa- n ying exercise guide to see the correct form for each exercise.
14 42 6 A TT ACHING THE SQUA T BAR The Squat Bar (25) can be attached to the Short Cables (43) at the squat stations (see A TT ACHING THE PULLEY HOUSINGS above) with the two Extension Straps (27) and four Clips (29). Adjust the length of the Extension Straps as necessary .
15 CABLE DIAGRAM The cable diagram shows the proper routing of the Long Cable (42). Use the diagram to make sure that the cable has been assembled correctly . If the cable has not been correctly routed, the resistance system will not function properly and damage may occur .
16 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building— T o increase muscle size, use a high amount of resistance. Y our muscles will adapt and grow as you progressively increase the intensity of your exer- cise by: • changing the level of resistance • changing the number of repetitions or sets performed.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of this manual for information about ordering replacement parts.
22 22 62 2 3 62 66 66 61 61 1 1 61 1 61 61 62 4 65 56 5 37 39 38 59 37 89 39 38 59 89 37 37 39 38 59 89 89 39 37 37 38 59 88 6 30 23 2 3 7 9 78 77 63 55 25 78 77 63 33 32 32 34 44 41 61 36 75 33 32 34 31 8 32 33 60 75 60 73 73 35 33 64 67 56 56 78 78 83 84 85 86 86 86 60 60 87 87 79 78 78 59 69 59 5 9 EXPLODED DRA WING A—Model No.
EXPLODED DRA WING B—Model No. WESY2966.0 R0606B 24 80 10 21 56 59 12 38 59 76 42 42 38 59 76 12 56 59 24 80 21 68 68 37 38 39 37 89 37 38 39 37 89 28 26 27 29 29 57 54 54 16 14 13 15 70 71 38 59 11 .
LIMITED W ARRANTY ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of five (5) years from the date of purchase. ICON warrants the resistance bars for the lifetime of the product.
デバイスWeider WESY2966.0の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Weider WESY2966.0をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider WESY2966.0の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider WESY2966.0の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider WESY2966.0で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider WESY2966.0を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider WESY2966.0の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider WESY2966.0に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider WESY2966.0デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
