WeiderメーカーWESY39522の使用説明書/サービス説明書
ページ先へ移動 of 35
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if parts are missing, we will guarantee com- plete satisfaction through assis- tance from our factory . TO A VOID DELA YS, PLEASE CALL DIRECT TO OUR TOLL- FREE CUSTOMER HOT LINE.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORT ANT PRECAUTIONS 3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 81 in. Width: 96 in. Length: 57 in. Squat Knee Rest Low Pulley Station High Pulley Station Lat Bar Swivel Carriage Adjustment Knob Adjustment Handle Bu.
5 ASSEMBL Y Make sure that you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and masking tape.
1. Locate and open the parts bags labeled “FRAME ASSEMBL Y 1” and “FRAME ASSEMBL Y 2.” Press a 2” Square Inner Cap (105) into the open end of the Long Base (120). Insert eight 5/16” x 2 1/2” Carriage Bolts (1 10) up through the Long Base (120) and the Short Base (2) as shown.
4. Press a 1 1/2” Square Inner Cap (67) into the Upright Extension (12). Attach the Upright Extension (12) to the Butterfly Upright (3) with two 5/16” x 3 3/4” Bolts (92), two 5/16” W ashers (90), and two 5/6” Nylon Locknuts (86).
8 7. Press a 2” x 3” Inner Cap (58) into the top of the Squat Upright (4). Slide the Squat Upright onto the two indicated 5/16” x 2 1/2” Carriage Bolts (1 10) in the Long Base (120). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt.
9 9. Attach a Roller (39) and two 5/16” W ashers (90) between the indicated set of holes in the Squat Slider (38) with a 5/16” x 3 1/2” Bolt (94), two 5/16” W ashers (90), and a 5/16” Nylon Locknut (86) as shown. Assemble the other three Rollers (39) to the Squat Slider (38) in the same manner .
10 14. Open the parts bag labeled “ARM ASSEMBL Y .” Press three 1 1/2” x 2” Inner Caps (21) into the Leg Lever (10). Lubricate a 3/8” x 2 1/2” Bolt (18) with grease. T urn the Leg Lever (10) so that the welded tab is on the indicated side, and attach the Leg Lever to the Seat Upright (9) with the Bolt and a 3/8” Nylon Locknut (87).
18. Locate and open the parts bags labeled “CABLE ASSEMBL Y” and “PULLEYS.” Lubricate the 3/8” x 7” Bolt (30) with grease. Attach the Swivel Cage (76) to the Swivel Carriage (46) with the Bolt and a 3/8” Nylon Locknut (87).
12 20. Remove the preattached 3 1/2” Pulleys (78) from the Small Pulley Plates (31). Wrap the Swivel High Cable (74) over a 3 1/2” Pulley (78). Attach the Pulley and a Cable T rap (68) to the second set of holes from the top of the Small Pulley Plates (31) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87).
13 24. Remove the preattached 3 1/2” Pulleys (78) from the Offset Double “U”-bracket (61). Wrap the Swivel Cable (17) around a 3 1/2” Pulley (78). Attach the Pulley to the Offset Double “U”- bracket (61) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87).
14 29. Wrap the Lat Cable (88) around a 3 1/2” Pulley (78). Attach the Pulley and a Long Cable T rap (102) to the T op Frame (6) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Jamnut (1 13). Make sure the Cable T rap is turned to hold the Cable in the groove of the Pulley .
15 35 36 38 37 34. Remove the preattached 3 1/2” Pulleys (78) from the Double “U”-bracket (62). Wrap the Butterfly Cable (69) under a 3 1/2” Pulley (78). Attach the Pulley to the Double “U”-bracket (62) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87).
16 41. Remove the preattached 3 1/2” Pulley (not shown) from the “U”-bracket (64). Attach the end of the Leg Lever Cable (75) to the “U”-bracket (64) with a 1/4” W asher (97) and a 1/4” Nylon Locknut (34). Note: Do not completely tighten the Locknut; it should be threaded only two turns onto the end of the Cable.
17 45. Wrap the Swivel Low Cable (72) under a 3 1/2” Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (120) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 46. Route the Swivel Low Cable (72) under the indicat- ed stack of Weights (44).
18 49. Wrap the Swivel Low Cable (72) over a 3 1/2” Pulley (78). Attach the Pulley and a Cable T rap (68) between the lower set of holes in the “U”-bracket (64) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure that the Cable T rap is turned to hold the Cable in the groove of the Pulley .
19 53. Wrap the Squat Cable (73) under a 3 1/2” Pulley (78). Attach the Pulley and a Cable T rap (68) to the second set of holes from the top in the indicated bracket on the Long Base (120) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87).
20 57. Press two 3/4” x 1 1/2” Inner Caps (1 16) and a 1 1/4” Square Inner Cap (1 17) into the Seat Bracket (1 1). Attach the Seat (16) to the Seat Bracket (1 1) with two 1/4” x 3/4” Screws (1 14), a 1/4” x 1 1/2” Screw (99), and a 1/4” W asher (97).
21 61 61. T urn the Squat Backrest (35) so that the four screw holes are closer to the bottom of the Squat Backrest than the top. Attach the Squat Backrest to the Squat Bracket (37) with four 1/4” x 3/4” Screws (1 14). T urn the knob on the Adjustment Knob (1 15) coun- terclockwise several times to loosen it.
22 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for various exercises.
23 ADJUSTING THE SQUA T ARM, SEA T , OR BUTTERFL Y BACKREST T o adjust the height of the Squat Arm (32), first turn the Adjustment Knob (1 15) on the Squat Bracket (37) counterclockwise several turns to loosen it. Next, pull the Handle and slide the Squat Bracket up or down to the desired position.
HIGH PULLEY (lbs.) 14 25 38 48 61 68 80 96 101 11 2 122 LOW PULLEY (lbs.) 14 25 36 44 60 70 80 91 104 111 122 LEG LEVER (lbs.) 22 35 53 67 91 111 122 148 160 184 190 BUTTERFL Y ARM (lbs.) 17 26 36 45 54 63 71 80 91 100 108 PRESS ARM (lbs.) 24 39 55 70 89 104 11 8 136 154 167 187 SQUA T ST A TION (lbs.
25 TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi- ately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent.
26 CABLE DIAGRAMS The cable identification chart below shows the ends of each cable and the lengths of the cables. The cable dia- grams on this page and the following page show the proper routing of the cables. The numbers in the diagrams show the routes of the cables.
27 Leg Lever Cable (75) Swivel Low Cable (72) 1 1 3 2 4 5 6 7 9 2 3 4 1 2 3 4 5 8 Swivel Cable (17).
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.
Note: Assembly is divided into four stages: 1) frame assembly , 2) arm assembly , 3) cable assembly , and 4) seat assembly . The hardware for each stage is packaged in separate bags. W AIT UNTIL YOU BEGIN EACH ASSEMBL Y ST AGE TO OPEN THE P ARTS BAG LABELED FOR THA T ASSEMBL Y ST AGE.
Cable Clip (83) 3 1/2" Pulley (78) (Not shown to scale) "V" Pulley (55) (Not shown to scale) 4 1/2" Pulley (1 19) (Not shown to scale) 3/8" x 3 3/4" Bolt (122) 3/8" .
3/8" x 2" Bolt (100) 3/8" x 1 3/4" Bolt (93) #10 x 1" Screw (14) 3/8" x 2 1/2" Bolt (18) 5/16" x 2 3/4" Bolt (85) 3/8" x 2 3/4" Bolt (101) 3/8&qu.
1 1/4" Square Inner Cap (1 17) 1" Round Inner Cap (29) 1 1/2" x 2” Inner Cap (21) 2" Square Inner Cap (105) 1 1/2" Square Inner Cap (67) 2" x 3” Inner Cap (58) 3/4”.
8 1 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL. SA VE THIS P ART LIST/EXPLODED DRA WING FOR FUTURE REFERENCE.
P ART LIST—Model No. WESY39522 R1202A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 1 2 1/2” W asher 2 1 Short Base 3 1 Butterfly Upright 4 1.
4 6 5 7 3 2 8 9 10 11 13 15 16 109 109 19 19 20 20 21 21 20 21 23 24 25 26 27 27 28 29 29 28 32 33 33 111 111 35 37 38 39 39 40 40 40 42 42 43 43 47 45 44 45 44 48 48 49 50 50 11 4 11 4 11 4 11 4 52 5.
デバイスWeider WESY39522の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Weider WESY39522をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider WESY39522の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider WESY39522の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider WESY39522で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider WESY39522を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider WESY39522の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider WESY39522に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider WESY39522デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
