WeiderメーカーWESY49201の使用説明書/サービス説明書
ページ先へ移動 of 35
QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete satisfaction through direct assis- tance from our factory .
1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3. The weight system is intended for home use only .
3 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 78 in. Width: 86 in. Length: 66 in. Foot Plate High Pulley Station Lat Bar Leg Lever Butterfly Arms Assist Arm Press Arm Weight Stacks Backrests Dip Ha.
4 ASSEMBL Y 1 8 8 11 51 27 1 4 3 1 51 5 1. Before beginning assembly , be sure that you have read and understand the infor- mation in the box above. Locate and open the parts bag labeled “FRAME ASSEMBL Y .” Press two 2” Square Outer Caps (51) onto the Stabilizer (5).
5 2. Slide the Assist Upright (74) and the Leg Press Upright (56) onto the indicated 5/16” x 2 1/2” Carriage Bolts (1) in the Stabilizer (5). The high side of the brackets on the Assist Upright and Leg Press Upright should be on the side shown. Hand-tighten four 5/16” Nylon Locknuts (3) onto the Carriage Bolts.
6 4. Press a 2” Square Inner Cap (27) into the end of the T op Frame (55). Press a 1 3/4” Square Inner Cap (44) into each end of the crossbar on the T op Frame.
7 7. Press a Weight T ube Bumper (64) into the end of the Short Weight T ube (108). Insert the Weight T ube into the front stack of Weights (25). Be sure that the pin on the Weight T ube is sitting in the pin groove in the top Weight. Lubricate the inside of the holes in a T op Weight (65).
8 9. Attach the upper ends of the Short Weight Guides (73) to the T op Frame (55) with a 5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and a 5/16” Nylon Locknut (3). Attach the upper ends of the Long Weight Guides (62) to the T op Frame (55) in the same manner .
9 12. Press a 1” Round Inner Cap (49) into one of the Press Arms (46). Press a 1 3/4” Square Inner Cap (44) into the Press Arm. Attach the Press Arm (46) to one side of the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3).
10 15. See the inset drawing. Attach the Military Press Arm (84) to the Pivot Arm (101) with two 5/16” x 2 1/4” Bolts (33) and two 5/16” Nylon Locknuts (3). Press two 1 1/2” Square Inner Caps (32) into the Military Press Arm (84). Press two 1” Round Inner Caps (49) into the Military Press Arm.
11 17. Attach the Left Pull-up Arm (75) and the Right Pull-up Arm (77) to the Assist Upright (74) with two 5/16” x 2 3/4” Bolts (1 1) and two 5/16” Nylon Locknuts (3). Attach the Left Dip Arm (78) and the Right Dip Arm (79) to the Assist Upright (74) with two 5/16” x 2 3/4” Bolts (1 1) and two 5/16” Nylon Locknuts (3).
12 20. W rap the High Cable (58) around a “V”-Pulley (50). Attach the Pulley and a Long Cable T rap (31) to the indicated bracket on the Front Upright (42) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21). Be sure that the Long Cable T rap is positioned to hold the Cable in place.
13 24. See the inset drawing. Attach a 3 1/2” Pulley (15) and a Cable T rap (66) to the upper hole in a Long “U”-Bracket (57) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable T rap is inside the Long “U”- Bracket.
14 27. Locate the Low Cable (23). Route the Low Cable under the 3 1/2” Low Pulley (102). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame (17) and that the Cable is between the Pulley and the crossbar on the Press Frame.
15 31. Attach the end of the Low Cable (23) to the Long “U”-Bracket (57) with a 1/4” Nylon Locknut (2) and a 1/4” W asher (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable so only a couple of threads are showing above the Nylon Locknut, as shown in the inset drawing.
16 34. W rap the Military Press Cable (72) around a “V”-Pulley (50). Attach the Pulley to the T op Frame (55) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21).
17 36. Slide a 5/16” W asher (8) onto a 5/16” x 2 3/4” Bolt (1 1). Insert the Bolt through the indicated hole in the Pivot Arm (101). The Bolt must be inserted from the side shown. Fully tight- en a 5/16” Nylon Jamnut (93) onto the Bolt. Wrap the Military Press Cable (72) around a 3 1/2” Pulley (15).
18 38. Locate the Leg Press Cable (99). Attach the end of the Leg Press Cable to the Long “U”- Bracket (57) with a 1/4” Nylon Locknut (2) and a 1/4” W asher (10). Do not completely tight- en the Nylon Locknut. It should be thread- ed onto the end of the Cable only a couple of turns, as shown in the inset drawing.
19 40. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Insert a 1/4” x 2 1/2” Carriage Bolt (92) through the center hole in a Seat Plate (37).
20 43. Attach the Front Backrest (41) to the Front Upright (42) with two 1/4” x 2 1/2” Screws (43) and two 1/4” W ashers (10). The Backrest must be oriented as shown. 44. Press a 1 1/2” Square Inner Cap (32) into the Front Seat Frame (36). Insert a 1/4” x 2” Carriage Bolt (38) through the center hole in the Seat Plate (37).
47. Press two 3/4” Round Inner Caps (34) into each Pad T ube (28). Insert a Pad T ube (28) into the Front Seat Frame (36). Slide a Foam Pad (30) onto each end of the Pad T ube. Insert the other Pad T ube (28) into the Leg Lever (29). Slide a Foam Foam Pad (30) onto each end of the Pad T ube.
22 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise.
23 A TT ACHING AND REMOVING THE SEA T T o attach the Seat (13), set the bracket on the Front Seat Frame (36) onto the indicated pins on the Front Upright (42). Attach the Front Seat Frame to the Front Upright with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40).
24 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. “T op” refers to the 6.5 lbs. top weight. The other numbers refer to the 12.5 lbs. weight plates. The butterfly arm resistance listed is the resis- tance for each butterfly arm.
TROUBLE-SHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immedi- ately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
26 CABLE DIAGRAMS The cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), the Military Press Cable (72), and the Leg Press Cable (99). Use the diagrams to be sure that the four cables and the cable traps have been assembled correctly .
27 Military Press Cable (72) Leg Press Cable (99) Rear Weight Stack— 1 2 3 4 7 6 5 3 2 4 — Rear Seat Frame 8 — Pivot Arm 1 — Long “U”-Bracket Military Press Cable (72) and Leg Press Cable .
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
Note: The assembly is divided into four stages: 1) frame assembly , 2) arm assembly , 3) cable assembly , 4) seat assembly . The hardware for each stage is packaged separately . W AIT UNTIL YOU BEGIN EACH ASSEMBL Y ST AGE TO OPEN THE P ARTS BAG LABELED FOR THA T ASSEMBL Y ST AGE.
5/16" Nylon Locknut (3) 1/4" W asher (10) 5/16" W asher (8) 1" Retainer (69) 3/8" W asher (9) 1/4" x 2 1/2" Screw (43) 3/8" Nylon Locknut (21) 1/4" x 2&quo.
5/16" x 2 3/4" Carriage Bolt (14) 3/8" x 3 1/2" Bolt (16) 5/16" x 5" Bolt (68) 3/8" x 3 3/4" Bolt (88) 3/8" x 8" Bolt (59) 5/16" x 6" Bolt (.
1" Round Inner Cap (49) 3/4" Round Inner Cap (34) 1/2" x 3/4" Spacer (61) 5/8" x 9/16" Spacer (7) 1 1/4" Round Inner Cap (109) 1" Round Cover Cap (70) 1 1/2&quo.
8 1 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL. SA VE THIS P ART LIST/EXPLODED DRA WING FOR FUTURE REFERENCE.
P ART LIST—Model No. WESY49201 R0602A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty .
60 27 21 50 55 86 11 8 15 12 44 88 15 58 21 44 21 3 61 62 24 3 58 71 2 65 108 64 25 26 19 9 3 3 49 6 22 46 46 16 3 9 15 21 59 23 21 17 27 1 4 10 43 41 42 21 3 50 31 86 70 69 69 70 21 47 44 45 44 45 48.
デバイスWeider WESY49201の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Weider WESY49201をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider WESY49201の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider WESY49201の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider WESY49201で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider WESY49201を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider WESY49201の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider WESY49201に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider WESY49201デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。