WeiderメーカーWESY74090の使用説明書/サービス説明書
ページ先へ移動 of 27
® USER’S MANUAL Model No. WESY74090 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference.
2 Limited W arranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 W ARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
4 ASSEMBLED DIMENSIONS: Height: 75 in. Width: 31 in. Length: 44 in. Weight Stack Leg Lever Butterfly/Press Arm Foam Roller Seat Backrest Thank you for selecting the versatile WEIDER ® 740 Weight System. The 740 offers a selection of weight stations designed to develop every major muscle group of the body .
5 Note: This introduction will save you more time than it takes to read it! Identifying Parts T o help you identify the small parts used in assem- bly , we have included a P ART IDENTIFICA TION CHART in the centre of this manual.
6 Frame Assembly 1. Before beginning assembly , make sure you have read and understood the information on page 5. Locate and open the parts bag labeled “FRAME ASSEMBL Y .” Press a 1 1/2” Square Outer Cap (27) onto each end of the Stabilizer (5) and place it on the floor as shown.
7 3. Attach the two Weight Bumpers (19) to the Stabilizer (5) with two #8 x 1” Screws (18). Slide the six Weights (25) onto the two tubes on the Weight Guide (62). Note: Make sure all of the Weights are turned so the pin grooves are on the same side and that the grooves are oriented as shown in the drawing.
8 6 6. Attach the two tubes on the Weight Guide (62) to the T op Frame (55) in the following manner: Slide a 5/16” x 6” Bolt (7) through one of the tubes on the Weight Guide (62) until the tip is barely visible on the other side. Position a 1/2” x 1” Spacer (51) and slide the Bolt through it.
9 9 9. Identify the Right Arm (48) and the Left Arm (47) by imagining yourself sitting on the seat. Note the posi- tion of the welded bracket (A) on each Arm. Arm identification is very important for this step. Lubricate both axles on the Press Frame (17).
10 12. Locate the parts bag labeled “CABLE ASSEMBL Y AND PULLEYS.” For cable identification and rout- ing during steps 12 through 27, refer to the Cable Diagram and Cable ID Chart on pages 15 and 16. Slide a 3/8” Flat W asher (9) and a 1/2” x 1/4” Spacer (44) onto a 3/8” x 2” Bolt (12).
11 16. Attach the loop at the end of the Short Cable (58) to the Weight T ube (63) with a 5/16” x 1 1/2” Bolt (1 1) and a 5/16” Nylon Locknut (3). 16 3 63 58 11 17. Locate the Butterfly Cable (76). It is approximately 87 1/2“ long and it has a closed loop on both ends.
12 19. Remove the pre-attached Pulleys (15) from the Pulley Bracket (57). Wrap the Butterfly Cable (76) around a 3 1/2” Pulley (15) in the direction shown. Attach the Pulley to the upper part of the Pulley Bracket (57) with a 3/8” x 1 3/4” Bolt (68) and a 3/8” Nylon Jamnut (22).
13 24. Wrap the Long Cable (23) around a 3 1/2” Pulley (15) in the direction shown. Attach the 3 1/2” Pulley (15) and a Cable T rap (66) to the indicated hole in the welded bracket on the Base (4) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21).
14 27. Hook the closed loop on the end of the Long Cable (23) onto the 3/8” Eyebolt (35) that is mounted on the Leg Lever (29). T ighten the 5/16” Nylon Locknut (3) that is securing the other end of the Long Cable (23) to the Upright/Base. 27 23 29 35 3 28.
15 30. Press a 3/4” Round Inner Cap (34) into each end of the Pad T ube (28). Insert the Pad T ube (28) through the indicated hole in the Leg Lever (29). Slide a Foam Pad (30) onto each end of the Pad T ube. 30 34 30 34 30 28 29 31. Make sure that all parts have been properly tightened.
16 Cable Diagram (2) Long Cable (23) 2 1 6 7 8 5 3 4 Cable ID Chart 58, 130” 76, 87 1/2” 23, 233”.
Attaching the Lat Bar to the Pulley Station Attach the Lat Bar (54) to the Short Cable (58) with a Cable Clip (53). Adjusting the Arms for Butterfly or Press Exercises The Left Arm (47) and Right Arm (48) can be adjusted for either butterfly or press exercises by turning the Locking Pin (75).
18 Tightening the Cables Woven cable, the type of cable used on the home gym system, can stretch slightly when it is first used. If there is slack in the Cables before resistance is felt, the Cables should be tightened. T o tighten the Cables, insert the Weight Pin (26, not shown) between the third and the fourth Weight, counting from the top.
19 ICON of Canada Inc. 900 de l’Industrie St-Jérôme, Québec Canada, J7Y 4B8 PLACE ST AMP HERE Press Butterfly Pulley Leg Weight Arm Arm Station Lever Plates (lbs.
Ordering Replacement Parts T o order replacement parts, simply call our Customer Service Department toll-free at 1-888-936-4266, Monday through Friday , 8 a.m. until 6:30 p.m. EST (excluding holidays). T o help us assist you, please be prepared to give the following information: 1.
WESY74090 R0700A Note: Assembly is divided into four stages: 1) frame assembly; 2) arm assembly; 3) cable, pulley and seat assembly . The hardware for each assembly stage is packaged separately . Wait until you begin each stage to open that parts bag.
1/4" Flat W asher (10) 5/16" Flat W asher (8) 3/8" Flat W asher (9) 3/8" Nylon Locknut (21) 1/4" Nylon Locknut (2) 3/8" Nylon Jamnut (22) 3/8" Plain Nut (56) 1/4&quo.
1" Retaining Ring (69) 3/8" x 2" Bolt (12) 3/8" x 3" Bolt (72) 3/8" x 2 3/4" Bolt (71) 3/8" x 1 3/4" Bolt (68) 1/2" x 1/4" Spacer (44) 1/2" .
1" Round Inner Cap (49) 1" Round Cover Cap (70) 3/4" Round Inner Cap (34) 1 1/2" Square Outer Cap (27) 1" Square Inner Cap (65) 3/8" Eyebolt (35) 1 3/4" Square Inner.
8 1 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Part List—Model No. WESY74090 R0700A Key No. Qty .
53 54 31 31 69 70 69 70 47 74 74 48 52 10 2 52 10 2 16 21 22 56 76 59 59 56 22 76 17 77 77 32 77 73 73 77 77 68 15 12 78 22 22 12 1 22 3 61 1 55 15 40 58 44 44 15 44 44 8 9 9 9 9 57 68 22 15 22 60 15 .
デバイスWeider WESY74090の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Weider WESY74090をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWeider WESY74090の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Weider WESY74090の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Weider WESY74090で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Weider WESY74090を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWeider WESY74090の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Weider WESY74090に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWeider WESY74090デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。