WellsメーカーBWB-1Sの使用説明書/サービス説明書
ページ先へ移動 of 16
SERVICE INSTRUCTIONS for BELGIAN WAFFLE BAKERS Model BWB-1S Part No. 502972 Rev. A S211 111000 cps IMPORTAN T : WELLS MF G . PROPRIE TARY INFORMATION TECHNICAL CONTENT OF THIS MANUAL IS DESIGNED FOR USE BY QUALIFIED PROFESSIONAL TECHNICIANS ONLY WELLS MANUFACTURING COMPANY 2 ERIK CIRCLE, P .
GENERAL SAFETY PROCEDURES Knowledge of proper procedures is essential to the safe operation of electrically energized equipment. In accordance with generally accepted product safety labeling guidelines for potential hazards, the following signal words and symbols are used throughout this manual.
TABLE OF CONTENTS General Safety Procedures Inside Cover Specifications 1 Features and Operating Controls 2 Servicing Precautions for This Equipment 3 T roubleshooting 4 Servicing Instructions 6 Wirin.
FE ATURES AND OPER ATING CONTROLS 8. POWER CORD 115VAC NEMA 5-15P 9. DATA PLATE Specifies power requirements 10. MICRO SWITCH Initiates timer 16. TEMPERATURE PROBE Thermistor temperature sensor 17. HANDLE ASSY Used to raise / lower / rotate grids 18. SUPPORT BRACKET Supports front of grids 19.
3 PRECAUTIONS FOR SERVICING THIS EQUIPMENT CAUTION: Never submerge electrical equipment in wate r. Avoid contaminating electrical components with water when cleaning cooking surfaces or cabinet. Disconnect electrical power to equipment prior to performing cleaning or other service.
4 TROUBLE SHOOTING B. TEMPERATURE CHECKS 1. Desired baking temperature is 390ºF ±5ºF (200ºC ±3ºC). 2. Turn the power switch ON and allow the W affle Baker to heat for a minimum of 30 minutes. Insert a pyrometer of known accuracy betwen the grids and allow the readings to stabilize.
5 D. VO LT AGE CHECKS NOTE : Resistance of the temperature probe is typically 5 megohm at room temperature, with resistance decreasing as temperature rises. A shorted temperature probe will cause a runaway condition, and an open probe will cause a continuous OFF condition.
6 A. CABINET ASSEMB LY 1. Insert the trademark plate from the front. From the rear of the cabinet, slide retainers over the trademark plate pins. Using a deep socket, tap the retainers down until they are flush with the cabinet surface. 2. Attach wires 1, 2, 3 & 4 to the switch.
7 B. BACK PANEL ASSEMB LY 1. Apply foam tape to the back panel flange - inside surfaces for the right, left and bottom; outside surface for the top. 2. Insert the power cord into the strain relief, then install the strain relief from the outside of the back panel.
C. TOP GRID 1. Prepare grid casting by applying a small amount of anti-sieze paste to all threaded holes. 2. Feed wires 5, 6 & 20 thru the right feed-thru hole. Attach wires 5 & 6 to the element terminals. Attach wire 20 to the center-most boss at the front of the casting.
9 E. GRID ASSEMB LY 1. Turn and position the grids so that the waffle-sides are facing each othe r. Thread the hi-temp tubing thru the shaft of the pivot housing. Attach the pivot housing to the bottom grid with screws (bottom hole) and screws with washers (middle hole).
1 0 F . PIVOT BEARING ASSEMB LY 1. The pivot bearing may be out of alignment as it comes from the box. T ap the collar of the bearing with a plastic hammer until the axis of the bearing is perpendicular to the base. Attach the pivot bearing to the inside of the cabinet.
1 1 G . BYPASS HI-LIMIT THERMOS TAT 1. The hi-limit thermostat in this Belgian W affle Baker has been found to be unnecessary. Wells BWB-1S has been tested and approved by UL for use without the hi-limit thermosat. 2. All units requiring service, whether in or out of warranty, should have the hi-limit thermostat bypassed.
PARTS BREAKDOWN 1 2 REF DESCRIPTION PART # # 1 BOTTOM PANEL 2 BACK PANEL 3 WRA P , CABINET ASSEMBLY 5 SWITCH SADDLE 6 TRADEMARK PLATE 7 RETAINER, TRADEMARK (pk 10) 51038 8 CORD, 125 v 15a NEMA 5-15p 5.
1 3 BWB-1S BELGIAN WAFFLE BAKER EXPLODED VIEW 20 67 43 42 79 25 24 23 17 20 18 3 6 7 65 64 1 41 75 32 22 39 21 44 5 10 40 15 28 62 50 66 48 45 47 2 76 27 46 19 12 8 31 9 76 77 78 16.
WELLS MANUFACTURING COMPANY 2 ERIK CIRCLE, P . O. Box 280 Verdi, NV 89439 Service Parts Dept. (888) 492-2782 fax: (888) 492-2783 w service @ ellsbloomfield.
デバイスWells BWB-1Sの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Wells BWB-1Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWells BWB-1Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wells BWB-1Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wells BWB-1Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wells BWB-1Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWells BWB-1Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wells BWB-1Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWells BWB-1Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
