WharfedaleメーカーS-1000の使用説明書/サービス説明書
ページ先へ移動 of 20
PROFESSIONAL POWER AMPLIFIERS Power Protect Bridge Peak A Peak B Professio nal Amplifie r Signal CH. B CH. A 2 8 3 7 1 9 4 6 0 10 5 2 8 3 7 1 9 4 6 0 10 5 Signal.
TABLE OF CONTENTS PAGE 1. FRONT AND REAR PAN EL REFERENCE DRAWINGS 2. WARNINGS AND WARRANTY INFORMATION 3. INTRODU CTION 4. GETTING STARTED 5. FRONT PANEL FEATURES AND CONTROLS 6. REAR PANEL FEATURES AND CONTROLS 7. INPUT “A” AND “B” MODE SWITCHES 8.
+ 1+ 1- POS NEG OUTPUT B 1+ 2+ POS NEG BRIDGED M ONO 2+ 2- POS NEG 1+ 1- OUTPUT A OUTPUT B OUTPUT A OUTPUT B BRIDGED MONO A + _ B BRIDGED + _ _ SLEEVE = GROUND SHIELD MODEL S-SERIES Professional Power Am plifier WWW.
WARNINGS AND WARRANTY INFORMATION Unpacking: All Wh arfedale Pro pr oducts are fully tested b efore leaving the factor y. After unpacking , please i nspect the unit . In the event of any noticed damage du e to shipping, cont act your dealer and the shippin g provider immedia tely to file a shipping damage claim.
3 Introduction Thank you for your purchase of a Wh arfedale Pro S-Series pr ofessional power amplifier. Please read this manual comp letely to ensure p roper operatio n and comple te understanding of th e features of these produ cts.
Getting Started 1. AC Power Connections All S-Series power amplifiers are equipped with an internal AC power supply. Connect the appropriate grounded IEC pow er cable to th e po wer amp BEFORE connecting it to the power outlet.
FRONT PANEL - FEATURES AND CONTROLS 1. Power switch: Push to turn powe r on or off. 2. Power On LED: Th is LED lights when the power is on for the amplifier. 3. Protect LED: This LED will light up when a fault is detected in the amplifier operation. 4.
6 REAR PANEL – FEATURES AND CONTROLS 1. INPUT “A” XLR and ¼” Ba lanced Line Input jacks: These XLR inputs are balanced input jacks and ¼” TRS (Tip / Ring / Sleeve) balanced / unbala nced inputs. These jacks are designed to b e connected to +4dBu ba lanced or unbalan ced line level so urces.
INPUT A & B MODE SWITCHES The MODE SWITCHES for the S-2500 pr ovide the means to config ure the amplifier in for a variety of different applications. The following l egend shows the available selections. 7 Switch 1: is not used INPUT A Switch 2: E ngage s the signal LIMITER in the ON (up) position and disengages it when OFF (down).
MODE SWITCH OPERATION LIMITER A limiter is a circuit that prevents signal over load and distortion in an audio s ignal path. When engaged, the internal limiter circ uit will keep the audio signal from going over a preset level threshold, thereby helping to prevent signal d istortion within th e amp lifier and in the speaker system.
OUTPUT “ A ” AND “ B ” WIRING OPTIONS Output wiring options consist of NL-4 “Speak on®-type” female connecto rs for the left and right o utputs along with industry standard binding posts for dire ct wiring conn ections or wiring with banana plugs.
USING OUTPUT JACK “ A ” NL-4 FOR BOTH OUTPUTS 10 BRIDGED-MONO MODE NL-4 WIRING * : FULL RANGE SHARED OUTPUT 1+ = POSITIVE - OUTPUT A 1 - = NEGATIVE - OUTPUT A 2+ = POSITIVE - OUTPUT B 2 - = NEGATI.
BINDING POST WIRING OPTIONS 11 As shown in the graph ic above, the stereo and bridged mono applications can be connected as indicated. Binding post wiring can be do ne with spade connectors, bare wire ends tightened into the binding posts or via banana plugs inserted into the e nd of the binding pos ts.
NEGATIVE LEAD TO SPEAKER POSITIVE LEAD TO SPEAKER 12 CONNECTING SPEAKER C ABLE WITH SPADE LUGS CONNECTING SPEAKER CA BLE WITH BANANA PLUGS NEGATIVE LEAD TO SPEAKER POSITIVE LEAD TO SPEAKER S-SERIES Pr.
BRIDGED MONO NEGATIVE LEAD TO SPEAKER POSITIVE LEAD TO SPEAKER CONNECTING SPEAKER CABLE BRIDGED-MONO 13 BRIDGE S-SERIES Professional Amplifiers + _ A + _ B B + _ BRIDGED-MONO MODE REQUIRES SWITCH #10,.
GENERAL OPERATING INSTRUCTIONS Make sure that the power switch is set to t he OFF position while making conne ctions to and from the power amplifier. Connect all external com ponents. Speakers, Microphones , instruments , etc. Check for secure connections.
15 S-SERIES Professional Amplifiers S- 1000 SPEC I FI CA T I ON S Ou tp u t P o w e r S te r e o : 180W + 180W / 8 Ω (0 . 1% T HD at 20 Hz -2 0k Hz ) 300W + 300W / 4 Ω (0. 1% T HD at 20Hz -20k Hz ) 200W + 200W / 8 Ω (0 . 1% T HD at 1k Hz ) 330W + 330W / 4 Ω (0 .
16 S-SERIES Professional Amplifiers S- 1500 SPECI FI CA T I ON S Out put Pow e r Ste re o: 300W + 300W / 8 Ω (0. 1% T HD at 20Hz -20k Hz ) 450W + 450W / 4 Ω (0. 1% T HD at 20Hz -20k Hz ) 320W + 320W / 8 Ω (0 . 1% T HD at 1k Hz ) 500W + 500W / 4 Ω (0 .
17 S-SERIES Professional Amplifiers S- 2500 SPECI FI CA T I ON S Out put Pow e r Ste re o: 490W + 490W / 8 Ω ( 0.1 % T H D a t 2 0 H z - 20 kH z ) 700W + 700W / 4 Ω (0. 1% T HD at 20Hz -20k Hz ) 500W + 500W / 8 Ω ( 0.1 % T H D a t 1 kH z) 770W + 770W / 4 Ω ( 0.
Wharfedale International LTD. IAG HOUSE Sovereign Court, Ermine Business Park, Huntingdon, Cambs, PE29 6XU, England www.wharfedalepro.com IAG Professional reserve s the right to al ter or improve specifi cations without notice.
デバイスWharfedale S-1000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Wharfedale S-1000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWharfedale S-1000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wharfedale S-1000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wharfedale S-1000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wharfedale S-1000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWharfedale S-1000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wharfedale S-1000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWharfedale S-1000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。