White Rodgersメーカー1F90W-71の使用説明書/サービス説明書
ページ先へ移動 of 36
OPERA TION GUIDE 5 Day/2 Day Electronic Digital Thermostat 1F90W -71 Operator: Save this booklet for future use! WHITE-RODGERS WHITE-RODGERS.
2 About Y our New Thermostat . . . Your new White-Rodgers Digital Thermostat uses the technology of a solid-state microcomputer to provide precise time/temperature control. This thermostat offers you the flexibility to design heating and cooling programs that fit your needs.
3 PROGRAMMING YOUR THERMOSTAT .................................... 19 PLANNING FOR YOUR NEEDS ENTERING YOUR PROGRAM Set Current Time and Day Enter Heating Program Enter Cooling Program CHECK YOUR PROGRAMMING QUESTIONS AND ANSWERS ................. 29 YOUR NEW THERMOSTAT'S FEATURES .
4 • Separate 5-day (weekday) and 2-day (week- end) setback programming • Simultaneous heat and cool program stor- age • Four separate time/temperature settings per 24-hour period • Computed En.
5 OPERA TING YOUR THERMOST A T SUBBASE THERMOSTAT BODY Before you begin programming your thermo- stat, you should be familiar with its features and with the display and the location and operation of the thermostat buttons. The information in this section will help you become familiar with your new thermostat so that you can easily program it.
6 these, then gently pivot the thermostat body down to connect the three pin connectors on the lower portion of the thermostat back. Gently push until the snap connectors engage. DO NOT FORCE OR PRY THE THERMOSTAT, as this may damage the unit. PARTS OF THE THERMOSTAT The Back of The Thermostat Body Turn the thermostat body over.
7 2. You may adjust the option switches for keypad lockout, limited temperature range, and automatic changeover from heat to cool (see OPERATING FEATURES ). Other than and , the buttons are located behind the thermostat door. To open the door, pull the door out from the top, then swing it down on its hinges.
8 The word BATTERY flashes on the display when the "AA" alkaline batteries are weak and should be replaced. The word BAT- TERY is displayed continuously (non-flash- ing) when thermostat is running on battery power only. FAN ON is displayed when the blower is operating continuously.
9 1 2 3 4 6 6 2 DAY 5 DAY 2 3 4 FAN AUTO FAN ON 5 DAY FAN AUTO 5 BATTERY TIME FWD SYSTEM HEAT-OFF-COOL-AUTO SET CLOCK VIEW PRGM HOLD TEMP TIME BACK FAN ON - AUTO SET DAY RUN PRGM ADV PRGM.
10 Used to initiate or review thermostat pro- gramming. Used to start program operation after pro- gramming. Also used to return thermostat to program operation after being in HOLD mode. Used to manually override programming to hold at a selected temperature (when HOLD is displayed).
11 10 11 12 13 14 15 16 17 18 9 7 8 5 DAY FAN AUTO TIME FWD SYSTEM HEAT-OFF-COOL-AUTO SET CLOCK VIEW PRGM HOLD TEMP TIME BACK FAN ON - AUTO SET DAY RUN PRGM ADV PRGM.
12 OPERATING FEATURES Now that you are familiar with the thermostat display and buttons, read the following informa- tion to learn about the many features of the thermostat.
13 use a pencil or small screwdriver to move the switch to the OFF position (see figure below). Leave the battery out of the thermo- stat for at least two minutes , to allow the thermostat to reset itself. See AUTOMATIC CHANGEOVER to determine proper posi- tions of Group B option switches #1 and #2.
14 utes , to allow the thermostat to reset itself. Replace the battery, reprogram the thermo- stat, if necessary, put the thermostat back on the wall, and restore 24v AC power.
15 display shows the temperature you want. The thermostat will override current pro- gramming and keep the room temperature at the selected temperature for two hours.
16 (long cycles), you may want to adjust the anticipation setting. A cooling anticipation setting of less than 10 may cause decreased compressor life. To adjust heat anticipation, press SET CLOCK and SET DAY at the same time. The display will show HEAT 5 (this is the factory prepro- grammed heating anticipation setting).
17 be replaced. The word BATTERY will be displayed continuously (non-flashing) when 24v AC power is not being supplied to the thermostat and the thermostat is operating on battery power only. • AUDIO PROMPTING — Each time you press a button, the thermostat will beep.
18 Total Keypad Lockout Switch #1 ON Switch #2 OFF To enable total keypad lockout, move Group A option switch #1 to ON (see figure above). To disable total keypad lockout, move op- tion switch #1 to OFF .
19 PROGRAMMING YOUR THERMOST A T Now you are ready to program your thermostat. This section will help you plan your thermostat's program to meet your needs. For maximum comfort and efficiency, keep the following guidelines in mind when planning your program.
20 2a. What time do the building occupants reach a maximum activity level (using lights, equip- ment, meeting rooms, etc.)? b. What temperature should the building be at this time? These will be your DAY tempera- ture settings. 3a. What time do the building occupants reach a minimum activity level (limited personnel in building)? b.
21 b. What temperature should the house be at this time? These will be your NHT (night) temperature settings. Now look at the factory preprogrammed times and temperatures shown on the following page. If this program will suit your needs, simply press RUN PRGM to begin running the factory preset pro- gram.
22 Determine the time periods and heating and cooling temperatures for your weekday pro- gram. You must program 4 periods for each day ( MOR , DAY , EVE , and NHT ). However, you may use the same heating and cooling tempera- tures for consecutive time periods.
23 WEEKDAY (5 DAY) WEEKEND (2 DAY) Start Time Temperature Start Time Temperature MOR HEAT DAY HEAT EVE HEAT NHT HEAT MOR COOL DAY COOL EVE COOL NHT COOL Heating/Cooling Schedule Plan.
24 WEEKDAY (5 DAY) WEEKEND (2 DAY) Start Time Temperature Start Time Temperature MOR HEAT DAY HEAT EVE HEAT NHT HEAT MOR COOL DAY COOL EVE COOL NHT COOL SAMPLE Heating/Cooling Schedule Plan 5:30 AM 8:.
25 Set Current Time and Day 1. Press SET CLOCK once. The display will show minutes only. EXAMPLE: 2. Press and hold either TIME FWD or TIME BACK until you reach the correct minutes. 3. Press SET CLOCK once. The display window will show the hour only. EXAMPLE: 4.
26 VIEW PRGM until you are at the point where you stopped programming. Then you may continue to enter your programs normally. If you want to stop programming at any time, simply press RUN PRGM to resume program operation. 1. Press SYSTEM HEAT-OFF-COOL-AUTO until HEAT is displayed.
27 6. Press VIEW PRGM . The currently programmed start time and heating temperature for week- day DAY will be displayed. 7. Repeat steps 3 through 5 to select the start time and heating temperature for the week- day DAY program. 8. Repeat steps 3 through 7 for the weekday EVE and NHT heating programs.
28 1. Press SYSTEM HEAT-OFF-COOL-AUTO until COOL appears. 2. Follow the procedure for entering your heat- ing program, using your selected cooling times and temperatures. CHECK YOUR PROGRAMMING Follow these steps to check your thermostat programming one final time before beginning thermostat operation.
29 Press FAN ON – AUTO until FAN AUTO is displayed (automatic cycling). QUESTIONS AND ANSWERS 1. How can I permanently change a part of my program? Press VIEW PRGM until you reach the time/tem- perature schedule you want. Then press TIME FWD or TIME BACK and and to change the program.
30 programming, press VIEW PRGM until you return to the point where you stopped program- ming. Then you may continue to program the thermostat normally. If you want to stop programming at this point, press RUN PRGM to start the normal program function.
31 During periods of low humidity (especially during cold weather), you may feel or see a spark discharge when you touch the ther- mostat. This may cause the program to be lost or the thermostat to display incorrectly. To correct this, remove the thermostat from the wall and disconnect the battery.
32 8. The display is flashing BATTERY. What does this mean? The "AA" batteries installed in the thermo- stat are low and should be replaced with fresh "AA" Energizer ® alkaline batteries. See OPERATING YOUR THERMOSTAT . 9. The display shows a continuous (non- flashing) BATTERY.
33 sons. • The EMR function is operating. The EMR function will automatically bring on the system automatically to bring the temperature to the selected level by the beginning of the next program period. See OPERATING YOUR THERMO- STAT . • You have programmed the incorrect day or time.
34 14. Between heating and cooling seasons, I want to turn my system off. Can I do this without affecting my thermostat pro- gramming? Any time you wish to turn your system off, simply press SYSTEM HEAT-OFF-COOL-AUTO until the display shows OFF . This will not affect your thermostat’s programming in any way.
35 batteries installed or if the installed batteries are dead. If you are changing the batteries after seeing a flashing BATTERY on the display, the installed batteries may be dead. If you remove the old batteries and install fresh ones within one minute, you should not lose your thermostat programming.
Part No. 37-5088A 9139 If you need further information on programming or operation, write to: White-Rodgers Division, Emerson Electric Co. 9797 Reavis Road St.
デバイスWhite Rodgers 1F90W-71の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
White Rodgers 1F90W-71をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWhite Rodgers 1F90W-71の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。White Rodgers 1F90W-71の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。White Rodgers 1F90W-71で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
White Rodgers 1F90W-71を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWhite Rodgers 1F90W-71の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、White Rodgers 1F90W-71に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWhite Rodgers 1F90W-71デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
