WiltonメーカーFK350-2の使用説明書/サービス説明書
ページ先へ移動 of 44
Owner's Manual Cold Saw Models: FK350-2, FK350-2SX, FK350-4, FK350-4SX FK350 FK350-SX WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Part No.
2 Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughou t the United States can give you quick service.
3 Table of Contents Warranty and Service........................................................................................................... ......................... 2 Table of Contents .........................................................
4 Warnings 1. Read and understand the entire o wner's manual before attempting assembly o r operation. 2. Rea d and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause seri ous injury.
5 23. Give your work undivided attention. Looking a round, carrying on a conversation and “horse-play” are careless acts that can result in seriou s injury. 24. Maintain a balanced stance at all times so that you do not fall into the blade or other moving parts.
6 Introduction The FK350 and FK350-SX are circular saws desi gned to provide a reliable solution to the nee ds of machine shops and prod uction environments that work with steel or iron.
7 FK350 Features FK350 Cold Saw FK350-SX Cold Saw.
8 Features Miter Cutting Head The miter cutting head is the unit that cuts the material and consists of a cast iron base, blade support unit and guard, transmission unit, and motor. The depth of cut is set by adjusting the depth cut stop . The miter cutting head swivels and locks into -45º, 90º, and +4 5º by means of a locking mechanism .
9 Installation Unpacking the machine Do not handle the pac ked machine using slings. To install the machine, first remove the packin g, paying particular attention not to cut any electric wires or hydraulic hose s.
10 Controls Control Panel – FK350 The Control Panel (Figure 4) is located on the front the cabinet stand and consists of the Power and High/Stop/Low switches, described below. Power Switch – The Power switch has two positions, Off and On. High/Stop/Low Switch – This switch control s the blade speed.
11 Operation Before using the machine: Check that safety devises (ex., blade guards) are in position and work perf ectly and that personal safety requirements are complied with. Check the sharpness of the blade and verify coolant flow. FK350 1.
12 Miter Adjustment The adjust the miter position follow the steps below while referring to Figure 10: 1. Move the miter position lock (A) to the right to release. 2. Adjust the head to the desired angle ranging from –45º to +45º by push ing on the back of the motor to the right or left.
13 Maintenance Maintenance Requirements All maintenance must be carried out with the power switched off . Failure to comply may result in serious injury! On completion of maintenance, ensure th at replaced parts and/or any tools used ha ve been removed from the machine before starting it up.
14 Lubrication For long life and trouble free operati on, it is essential that this machine is kept well lubricated. The vice and leadscrew should be oiled daily. Pivot joints and bearings should be greased weekly Check t he gearbox oil level weekly, full level is top of sight glass with head in full up position.
15 Blade Selection When using the FK350 col d saw, it is important to select the correct type of blade for the material to be cut. This section explains the limitations and specific applications of the different types of blades.
16 Blade Structure For non--ferrous metals, it is common to use circular saws with brazed hard metal HM cutting edge, consisting of a disc made of alloy tool steel (71Cr1) on which the shape of the teeth and the seats for the cutting edg es are made of Widia K10.
17 Figure 17 Short swarf material such as bra ss, bronze, aluminum and hard cast iron req uire smaller cutting angles beca use the swarf becomes crushed immediately and the rake a ngle has little effect during the cutting stage.
18 Troubleshooting Troubleshooting – Blade and Cutting Problems Problem Probable Cause Solution Incorrect lubricant/coolant fluid Ensure proper coolant flo w. Material too hard Check the cutting speed, feed speed and air pressure parameters and the type of blade you are using.
19 Troubleshooting – Machine Fault & Operating Problems Problem Probable Cause Solution Electrical power supply Check: the phases; the cables; the plug; the socket. Also check that the motor connections are in place. Transformer Check that the voltages are present both on the in put and output.
20 Head Assembly – FK350 & FK350-SX Index No. Part No. Description Size Qty 1 ............... FK350-201 ............... Head Body ........................................................... ................... ................. 1 2 .............
21 Head Assembly – FK350 & FK350-SX.
22 Power Feed Assembly – FK350-SX Index No. Part No. Description Size Qty 1 ............... FK350SX-701 .......... Spring Bracket A .................................................. ........................ ............ 1 2 ............... FK350SX-702 .
23 Power Feed Assembly – FK350-SX.
24 Stock Stop Assembly Index No. Part No. Description Size Qty 1 ............... FK350-501 ............... Block .................................................................... .............. ...................... 1 2 ............... FK350-502 .
25 Stand Assembly – FK350 Index No. Part No. Description Size Qty 1 ............... FK350-601 ............... Cabinet Stand ...................................................... .................... ................ 1 2 ............... FK350-602 ..
26 Stand Assembly – FK350-SX Index No. Part No. Description Size Qty 1 ............... FK350SX-601 .......... Cabinet Stand ...................................................... ....................... ............. 1 2 ............... FK350SX-602 .
27 Stand Assembly – FK350-SX.
28 Base Assembly – FK350 Index No. Part No. Description Size Qty 1 ............... FK350-101 ............... Base ..................................................................... .............. ...................... 1 2 ............... FK350-102 .
29 Base Assembly – FK350.
30 Base Assembly – FK350-SX Index No. Part No. Description Size Qty 1 ............... FK350-101 ............... Base ..................................................................... .............. ...................... 1 2 ............... FK350-102 .
31 Base Assembly – FK350-SX.
32 Manual Vise Assembly – FK350 Index No. Part No. Description Size Qty 1 ............... FK350-301 ............... Base ..................................................................... .............. ...................... 1 2 ............... FK350-302 .
33 Manual Vise Assembly – FK350.
34 Power Vise Assembly – FK350-SX Index No. Part No. Description Size Qty 1 ............... FK350-301 ............... Base ..................................................................... .............. ...................... 1 2 ..............
35 Power Vise Assembly – FK350-SX File 27.
36 Guard Assembly – FK350 & FK350-SX Index No. Part No. Description Size Qty 1 ............... FK350-401 ............... Guard A ................................................................ ................ .................... 1 2 .........
37 Guard Assembly – FK350, FK350-2SX.
38 In-Feed Table Assembly Index No. Part No. Description Size Qty 1 ............... FK350-701 ............... Bracket ................................................................ ............... ..................... 1 2 ............... FK350-702 .
39 Out-Feed Table 1 ............... FK350-801 ............... Guide Block .......................................................... .................. ............... EA 2 ............... FK350-802 ............... Guide Rail .........................
40 Pneumatic Drawing – FK350-SX Wiring Diagram – FK350.
41 Wiring Diagram – FK350-SX.
42 --NOTES--.
43 --NOTES--.
44 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.com.
デバイスWilton FK350-2の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Wilton FK350-2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWilton FK350-2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wilton FK350-2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wilton FK350-2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wilton FK350-2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWilton FK350-2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wilton FK350-2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWilton FK350-2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
