Woods EquipmentメーカーRD990Xの使用説明書/サービス説明書
ページ先へ移動 of 48
OP E R A TO R ' S M A NU A L RE A R M O U N T MO W ER S MAN0845 (Rev . 4 /29/201 1 ) T ested. Proven. Un beat able . RD990X.
2 Introduction Gen’l (Rev . 3/5/2 010) T O THE DEALER: Assemb ly and prop er installati on of this product is the respons ibil ity of the Woods ® dea ler .
Introduction 3 MAN084 5 (1/12/20 10) T ABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SPECIFICATI ONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Introduction MAN084 5 (1/12/201 1) SPECIFICATIONS RD990X 3-Point Hitch Category 1 and 2 Cutting Width 90" Cutting Hei ght Rang e 1-1/2" - 7 " Operating Weight with Chain Shi eldin g 1200 lbs Blade S peed ( feet per m inute) 17,000 Blade S peed ( RPM) 2,074 Blade S pin dles 3 Number of Blade s 6 Universal Drive Seri es ASAE Cat.
Safety 5 PRD Mower (9/13/2005) TRAINING Saf ety i nst ruct ions are i mpor t an t! Re ad al l att achment and power unit manuals; follow all safety ru les and safety d ecal i nformat ion. (Rep lace- ment manua ls and safety d ecals ar e avai lable f rom your dealer .
6 Safety PRD Mowe r (9/13/2005 ) Inspect a nd clea r area of s tones , branch es, or other hard object s that might be thrown, causing injury or damage. Never direct discharge toward people, animals, or property . Keep byst a nders away f rom equipment.
Safety 7 PRD Mower (9/13/2005) Y our dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.
8 Safety MAN084 5 (1/12/201 1) 9 - 571 23 9" Red Rear R eflector SHIELD MISSING DO NOT OPERA TE PUT SHIELD ON DANGER 18867- -B 6 - 15503 5 - 188 67 1 - Serial Numb er Plate MODEL NO. SE R IAL NO. W oods Equipment Company Oregon, Illinois, U.S.A. BE CAREFUL! Use a cl ean, da mp clo th to cle an safety d ecals .
Safety 9 MAN084 5 (1/12/20 1 1) SAFETY & INSTRUCTIONAL DECALS A TTENTION! BECOME ALERT! YOUR SAFETY IS INVOL VED! Replace Immediatel y If Damaged! 33347E F ALLING OFF CAN RESUL T IN BEING RUN OVER. T ractor must be equipped with ROPS ( or ROPS CAB) and seat belt.
10 Operation MAN084 5 (1/12/201 1) OPERATION The opera tor is r espons ible for the safe operatio n of the mower . The operato r must be p roperly trai ned. Operators should be fam iliar with the mowe r , th e trac- tor , and all s afety practic es befor e starting o peration .
Operation 11 MAN084 5 (1/12/20 1 1) Refer to Figure 2 1. For Catego ry 1 h itch, position mower h itch arms (E) with offset to ward center of mower . For Category 2 hitch , pos ition mow er hitc h arms (E) with offset toward outside of mower . 2. Attach the mowe r hitch pins ( B) to lower trac tor lift arms an d secure.
12 Operation MAN084 5 (1/12/201 1) 9. T o raise front of mowe r , move spacers und er front cast er wheel a rms . Figure 4 . Cutting He ight A djustmen t Rememb er , m easurem ent at locat ion A ( Figur e 4) should not be less than loc ation B and should not be over 1/2 " greate r than loc ation B.
Operation 13 MAN084 5 (1/12/20 1 1) FRONT CASTER WHEEL INTERFERENCE CHECK NOTICE ■ Do not operate tr actor and mower unt il this interfer ence c heck h as be en pe rformed. If yo u change tr actors, you must perfor m the check for that mou nting. Figure 8 .
14 Operation MAN084 5 (1/12/201 1) Plan your mo wing patter n to travel str aight fo rward whenever possib le. Mo w with u ncut gra ss to the right. This will dist ribute th e clippi ngs over th e cut area. Uneven T errain Do not operate or transpo rt on steep slopes.
Owner Service 15 MAN084 5 (1/12/20 1 1) OWNER SER VICE The info rmation in t his s ection i s written for oper ators who po ssess basic m echan ical skills. If yo u need help, your dea ler h as train ed ser vice te chni cians av aila ble. For your protec tion, read and follow the safety informa- tion in th is ma nual.
16 Owner Service MAN084 5 (1/12/201 1) Figure 10 . Lubricatio n Points & Chart REF DESCRIPTION FREQUENCY 1 Drive line U-J oints 8 Hours 2 Gearb ox (Fill to center of ho rizontal s haft with SAE 90.
Owner Service 17 MAN084 5 (1/12/20 1 1) Figure 1 1 . B elt Rout ing BEL T SER VICE Belt Re placeme nt One of the major cau ses of belt fail ure is improp er installa tion. Be fore installi ng a new belt, ch eck the fol- lowin g: 1. Check pu lley sh afts and bearing s fo r wear .
18 Owner Service MAN084 5 (1/12/201 1) Blade In stallation Y our dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous. Figure 13 . Blade Asse mbly 1. Install bla de pin ( 3) thru blade ( 2) and bl ade spindle (1).
T roubleshooting 19 MAN084 5 (1/12/20 1 1) TROUBLE SHOOTING MOWING CONDITIONS PROBLEM POSSIBLE CAUSE SOLUTION Gras s cut highe r in ce nter of swath t han at e dge Height of m ower high er at re ar than at fro nt Adjust mowe r height and attitude so that mower rear a nd front ar e with in 1/2 in ch of sam e heig ht.
20 T roubleshooting MAN084 5 (1/12/201 1) TROUBLE SHOOTING BEL T CO NDIT I ONS * Check belt f or damage by la ying it flat on the flo or . A belt that do es not lie flat ( has hum ps or twists, i ndicatin g broke n or stretc hed co rds) m ust be repla ced.
T roubleshooting 21 MAN084 5 (1/12/20 1 1) NOTES.
22 Dealer Service MAN084 5 (1/12/201 1) DEALER SER VICE The info rmation in thi s se ction is written for de aler ser - vice per sonnel. T he repair desc ribe d here requ ires special skil ls and tools.
Dealer Service 23 MAN084 5 (1/12/20 1 1) Figure 16 . S pindle Di sasse mbly Spindle Assem bly Refe r to Figu re 17 . Bearing cones and cups are de signed to wo rk toge ther . It is impor tant to pos ition them s o bearin g cone tape r mates wit h cup taper .
24 Dealer Service MAN084 5 (1/12/201 1) 2. Install pulle y (12) and split taper bus hing (13) wit h integral key (1 4) on spi ndle s haft. Make sur e bushing is in co ntact with sleev e on spi ndle sha ft. 3. Alterna tely tight en spl it taper bushi ng cap screws to 20 lbs-ft.
Dealer Service 25 MAN084 5 (1/12/20 1 1) 1. Clean area in housing wh ere seal outer di ameter (OD) sea ts. Apply a t hin c oat of Per matex . 2. Inspect a rea of sh aft where s eal seats. Rem ove any bu rr s or ni cks wit h an em ery c lot h. 3. Lubricate gear sha ft and seal lips.
26 Dealer Service MAN084 5 (1/12/201 1) 4. Remove fo ur cap screws (9 ), flat w asher (1 1 ), and remove shiel d (5) from gear box. 5. Remove c astle n ut (14) a nd har dware from outpu t shaft of ge arbox. 6. Remove s heave (4) from g earbo x. 7. Remove f our b olts (9) th at attach gearbox to gearbox stand and remove gearbo x.
Dealer Service 27 MAN084 5 (1/12/20 1 1) 16. Check that the ge ar backl ash is betw een 0.006 ” and 0.01 6”. Y ou shou ld no t have to ad just the backla sh. 17. Press in i nput oil seal ( 19), usi ng tube o f corre ct diamete r . B e careful not to damage seal li p.
28 Dealer Service MAN084 5 (1/12/201 1) 3. Clamp cup in vise a s shown i n Figur e 25 an d tap on yoke to compl ete ly remo ve cu p from yo ke. Repeat S tep 2 a nd S tep 3 for opp osite cup. Figure 25 Figure 26 4. Place u niver sal cr oss in vis e as s hown i n Figur e 26 and tap on yo ke to re move cup.
Assembly 29 MAN084 5 (1/12/20 1 1) ASSEMBLY INSTRUCTIONS DEALER SET -UP INSTRUCTIONS Assemb ly of this mower is the responsi bility of th e Woods dealer . If shoul d be del ivered to the own er com- pletely as sembled, lub ricated , and adjuste d for normal cutting c ondit ions.
30 Assembly MAN084 5 (1/12/201 1) T orque Caster Arms 1. Place m ower on a hard l evel su rface. 2. Loosen c ap s crews a nd lock nuts on all four caster wheel arms . This allo ws cle arance in the caster wheel a ssembl ies to be equali zed. 3. T o rque all cap s crews and nuts to 85 lbs-ft.
Assembly 31 MAN084 5 (1/12/20 1 1) Figure 31 . Chain S hield Ins tallatio n Inst all Chain Shie lding Full chain shielding must be installed when operating in populate d areas or other areas where thrown obj ects could inju re peop le or dam age property .
32 Assembly MAN084 5 (1/12/201 1) Fig ure 33 . Quick Hi tch Kit Installation (Option al) Inst all Q uick Hitch (Optional) NOTE: This kit al lows mo wer to fi t Categ ory 1 or Category 2 standard q uick hitc hes. 1. Lower hi tch arms must be loc ated i n cent er attachment hole.
Dealer Check List s 33 MAN084 5 (1/12/20 1 1) DEALER CH ECK LIST S PRE-DELIVERY CHECK LIST (DEALER’S RESPON SIBIL ITY) Inspect the equipment th oroug hly after assemb ly to ensure it is set up pro perly before deli vering it to the cust omer . The follow ing check lis ts are a reminder of points to insp ect.
34 Notes MAN 084 5 (1/ 12/ 201 1 ) NOTES.
Part s 35 MAN084 5 (1/12/20 1 1) P ARTS INDEX MAIN FRAME AS SEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 - 3 7 GEARBOX A SSEMB LY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 DRIVESHAF T ASSEMBL Y .
36 Part s MAN084 5 (1/12/201 1) RD990X MAIN FRAM E ASSEMBLY.
Part s 37 MAN084 5 (1/12/20 1 1) RD990X MAIN FRAM E ASSEMBLY REF P ART QTY DESCRIPTION 1 ----- 1 Deck (not sold sep arately) 2 103278 6 2 Lower Hi tch Arm 3 56598 2 Sle eve .8 85 x 1.12 5 x 2.6 2 4 19524 2 Sle eve .6 4 x 1.00 x 2.09 HT 5 103279 5 2 A-Frame Arm 6 103279 8 1 Sleeve .
38 Part s MAN084 5 (1/12/201 1) RD990X GEARBOX ASSEMBLY REF P ART QTY DESCRIPTION A 1002499 1 Gearbox Asse mbly , Complet e 1 57458 1 Gear , Crown 25 T M5.3 2 NSS 1 Gearbox Housi ng 3 1005320 1 Shaft, Input 1- 3/8 -6 4 1005321 1 Shaft, Outpu t 1-1/4 5 57491 1 Pinion Gea r 13T M5.
Part s 39 MAN084 5 (1/12/20 1 1) RD990X DR IVE SHAF T ASSEMBLY REF P ART QTY DESCRIPTION A 1029937 1 Drive As sembly Compl ete 1 40574 2 Y oke, 1-3/8-6SP ( compl ete with lock co llar) 2 1 10 2 Cross .
40 Part s MAN084 5 (1/12/201 1) RD900X BLADE & SPINDLE ASSEMBLY REF P ART QTY DESCRIPTION 1 1032800 1 Blade S pindle, C omplet e 2 18359 1 Sleeve 1-3/ 8 x 1-3/4 x 5/8 3 2715 2 Seal 1.
Part s 41 MAN084 5 (1/12/20 1 1) RD990X CHAIN SHIELD ING ASSEMBLY REF P ART QTY DESCRIPTION 1 1032821 2 Front Chain Shield Pla te 2 1032832 1 Right Corner Chain Sh ield Plate 3 1032833 1 Left Co rner .
42 Part s MAN084 5 (1/12/201 1) RD990X FRONT ROLLER ASSEMBL Y (OPTIONAL) QUIC K HIT CH KI T (OPT IONA L) REF P ART QTY DESCRIPTION A 1032828 1 Front Roller Ki t - Comp lete 1 1032829 1 Roller Brac ket 2 100641 8 1 Rolle r , 4 x 7.38 3 1006420 1 S pa cer , .
Appendix 43 Bolt T orque & Size Chart s (Rev . 3/28/2007 ) BOLT T ORQUE C HART Always tighten hardwar e to the se value s unl ess a di fferent torque valu e or ti ghtening procedur e is listed f or a spe cific applica tio n. Fasteners must al ways be rep laced with the s ame grad e as spec ified in the ma nual parts list.
44 Appendix Bolt T orque & Size Charts (Rev . 3/28/2007) BOLT SIZE CHART NOTE: Chart s hows b olt thr ead s izes an d corr espond ing he ad (wren ch) sizes f or standa rd SA E and metric bolts. ABBREVIATIONS AG ..... ....... .......... ...... ....
Index 45 MAN084 5 (1/12/20 1 1) INDEX A Assembly Chai n Shie ldi ng 31 Dealer Set- Up Instr uctions 29 Initia l Oil F ill 30 Optional E quipme nt Front Roller 31 D Dealer Check List s Delivery (Dealer.
F-3079 (Rev . 2/14/201 1) W oods Eq uipment Company 260 6 South Illinois Route 2 Post Office Box 10 00 Oregon, Illinois 61061 USA 800-319-663 7 tel 80 0-3 9 9-6 637 fa x www .W oodsEquipment.com W ARRANTY All Models Except Mow ’ n Machine TM Zero-T urn Mowers Plea se En ter In fo rma tion B elow an d Save for F utu re R efer ence .
F-8494 (Rev . 6/23/2005) W ARRAN TY (Replacement Parts F or All Models Except Mo w’ n Machine TM Zero-T urn Mo w ers and W oods Boundary TM Utility V ehicles) W oods Equipment Co mpan y (“W OODS.
W oods Equip ment Com pany 2606 South Il linoi s Route 2 P ost Office Bo x 1000 Oreg on, Ill inois 61061 815-7 32-214 1 tel 815-7 32-758 0 f ax www .W oodsEquipmen t.com MAN0845 © 201 1 Woods Equipment Com pany . All rights reserved. WOODS, t he Woods logo, and "T est ed.
デバイスWoods Equipment RD990Xの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Woods Equipment RD990Xをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWoods Equipment RD990Xの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Woods Equipment RD990Xの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Woods Equipment RD990Xで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Woods Equipment RD990Xを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWoods Equipment RD990Xの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Woods Equipment RD990Xに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWoods Equipment RD990Xデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。